CarProblemsDB

2010 Mazda Mazda6 problems, recalls & MPG

NHTSA has received 225 complaints from owners of the 2010 Mazda Mazda6, most often about the body & structure. There are 9 safety recalls for this model year.

3.4out of 10
Our verdict
Avoid this year
  • More complaints than 85% of 2010 vehicles
  • Most reported problem: body & structure (27% of complaints)
  • 9 safety recalls
  • 5 crashes, 2 fires, 2 injuries reported
How we score
Complaints225
Recalls9
MPG combined—
Safety—

Most reported 2010 Mazda Mazda6 problems

Owner complaints filed with NHTSA, grouped by problem area. One complaint can mention several areas.

Airbags54 (24%)
Suspension43 (19%)
Steering29 (13%)
Brakes17 (8%)
Tires6 (3%)
Wheels6 (3%)
Engine & cooling5 (2%)
Transmission & powertrain5 (2%)
Fuel & propulsion system3 (1%)
Seat belts3 (1%)
Seats2 (1%)
Doors, latches & locks1 (0%)
Equipment1 (0%)
Speed control (cruise, throttle)1 (0%)

When owners reported problems

12010
112011
22012
32013
202014
222015
312016
392017
372018
182019
72020
82021
72022
102023
52024
22025
22026

Complaints by the year they were filed.

Recent owner complaints

Jun 23, 2026suspension
I recently had my front subframe replaced as part of your recall, however, the rear subframe and all components attached are suffering from the exact same rust and potential component failure as the front. I was replacing my brakes today and noticed that the entire structure is on the verge of complete failure. The right rear suspension already makes unusual noises when going… Read more

I recently had my front subframe replaced as part of your recall, however, the rear subframe and all components attached are suffering from the exact same rust and potential component failure as the front. I was replacing my brakes today and noticed that the entire structure is on the verge of complete failure. The right rear suspension already makes unusual noises when going over even small bumps and I imagine if I were to hit a large pothole that would probably be the end of this car. I imagine all similar Mazda 6s in the midwest suffer from the exact same degradation and it is a major safety concern. There are places where there's chunks of subframe missing because it has rusted completely through and just disintegrated.

NHTSA complaint #11746080
Feb 5, 2026suspension, unknown or other
I looked up recalls on my vehicle and it states that the 2011 Mazda6 is  part of a recall (NHTSA 19v-323, Mazda 2818i) covering 2011-2013 models for front cross member (subframe) corrosion due to insufficient rust protection . In salt-belt states, this corrosion can cause the lower control arm to detach, reducing steering control and increasing crash risk.  Key details… Read more

I looked up recalls on my vehicle and it states that the 2011 Mazda6 is  part of a recall (NHTSA 19v-323, Mazda 2818i) covering 2011-2013 models for front cross member (subframe) corrosion due to insufficient rust protection . In salt-belt states, this corrosion can cause the lower control arm to detach, reducing steering control and increasing crash risk.  Key details regarding the 2011 Mazda6 subframe recall: scope: the recall affects specific 2011-2013 Mazda6 vehicles (and 2009-2010 models in a previous, related recall). Location restrictions: vehicles must have been originally sold in, or currently/previously registered in, 23 "salt belt" states (including ct, ny, mi, mn, oh, etc.). The issue: the front cross member may experience severe corrosion, causing structural failure of the passenger-side lower control arm mounting point. Symptoms: drivers may notice a change in steering alignment or a broken cross member. Remedy: dealers will inspect the cross member and replace it if necessary. Action required: owners should contact their local Mazda dealership to check their VIN for open recalls.  The recall was officially announced in may 2019 and is an expansion of a 2018 action.

NHTSA complaint #11715942
Mar 21, 2025steering, structure
The contact owns a 2010 Mazda Mazda6. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently veered to the left. There was no warning light illuminated. The contact stated that the vehicle became difficult to steer. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the engine cradle had failed and was… Read more

The contact owns a 2010 Mazda Mazda6. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently veered to the left. There was no warning light illuminated. The contact stated that the vehicle became difficult to steer. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the engine cradle had failed and was severely rusted and needed to be replaced. The vehicle was not repaired. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 114,000.

NHTSA complaint #11649768
Feb 19, 2025air bags

The airbag light is still flashing on the dashboard after the airbag recall on this vehicle was fixed. It may be related to a different recall, which is safety campaign #16v594000.

NHTSA complaint #11643653
Nov 9, 2024suspension

Extensive rust and corrosion in rear subframe. So severe the vehicle is unsafe to drive.

NHTSA complaint #11624391
Jul 28, 2024suspension
2010 Mazda 6 I series sedan the entire rear subframe/cradle is rotted along with all the other parts connected to it, the a arm, bumper stops, control arms, rear sway bar the entire rear under carriage. Took it to the shop and they said there have been several complaints about this exact issue on several of these cars from 09-13 models. The parts was not painted correctly… Read more

2010 Mazda 6 I series sedan the entire rear subframe/cradle is rotted along with all the other parts connected to it, the a arm, bumper stops, control arms, rear sway bar the entire rear under carriage. Took it to the shop and they said there have been several complaints about this exact issue on several of these cars from 09-13 models. The parts was not painted correctly like the front that was recalled. Exposed to all weather elements, the shop wants almost 4k for labor only to fix but the main problem is finding the rear subframe on these cars is almost impossible next to cost a fortune. Now I have a yard ornament. Junk yard wants to give me 170 bucks for the car but im not doing that. Mazda needs to fix this issue. I would of never know it was rotted out unless I took it to the shop for rear swaying and sagging. Its all over the road. Very dangerous and will cause a wreck almost certainly. Please someone do something about this issue. Dont have the money to fix this let alone buy another car.

NHTSA complaint #11604971
May 7, 2024suspension
The rear subframe is compromised; it separated from the body of the car. The vehicle is in my driveway and available for inspection should the need arise. The rear end had felt a bit shaky for a month so I took it to my mechanic, who declared the vehicle "unfit for the road" due to the fact that the subframe was rotted away and detached from the car itself. I was told one… Read more

The rear subframe is compromised; it separated from the body of the car. The vehicle is in my driveway and available for inspection should the need arise. The rear end had felt a bit shaky for a month so I took it to my mechanic, who declared the vehicle "unfit for the road" due to the fact that the subframe was rotted away and detached from the car itself. I was told one big bump is an accident waiting to happen...pieces of the car would go flying and I could be left with zero mobility to evade oncoming traffic. The possibility of projectiles injuring anyone around the car was enough for me to park it. The car has not been inspected by Mazda, the police, or insurance because there was no accident. Since it's not safe to drive, I took the word of my independent mechanic rather than driving it to a dealership. There were no warnings other than a bit of a sway in the rear end, which I originally attributed to its age. I've researched the issue and it seems to be a result of subpar quality with regard to the metal that was used in manufacturing.

NHTSA complaint #11587423
Feb 15, 2024structure
The contact owns a 2010 Mazda Mazda6. The contact stated while driving 40–45 MPH, there was an abnormal sound coming from the vehicle. The TPMS warning light was illuminated. The vehicle was taken to an independent mechanic, who informed the contact that the rear main sub frame was completely rusted. There was a crack detected in the middle of the sub frame. The vehicle was… Read more

The contact owns a 2010 Mazda Mazda6. The contact stated while driving 40–45 MPH, there was an abnormal sound coming from the vehicle. The TPMS warning light was illuminated. The vehicle was taken to an independent mechanic, who informed the contact that the rear main sub frame was completely rusted. There was a crack detected in the middle of the sub frame. The vehicle was taken to the local dealer, where it was diagnosed that the rear sub frame was rusted and needed to be replaced. The vehicle was not repaired. The manufacturer informed the contact that it was normal wear and tear, but no assistance was provided. The failure mileage was approximately 130,000.

NHTSA complaint #11572146

2010 Mazda Mazda6 recalls (9)

Recall 19V7820002019Air bags:frontal:passenger side:inflator module Park it — do not drive

Mazda north american operations (Mazda) is recalling certain 2007-2012 cx-7, cx-9, and 2009-2012 maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began december 3, 2019. Owners may contact mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317f. Note: this recall supersedes recalls 16v356 and 17v012.

Recall 18V7170002018Air bags:frontal:passenger side:inflator module Park it — do not drive

Mazda north american operations (Mazda) is recalling certain 2014-2015 Mazda cx-9 vehicles sold, or ever registered in the states of alabama, california, florida, georgia, hawaii, louisiana, mississippi, south carolina, texas, puerto rico, american samoa, guam, the northern mariana islands (saipan), and the u.s. Virgin islands or "zone a." additionally, unless covered in "zone a," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 cx-7, and 2011-2015 cx-9 sold, or ever registered in the states of arizona, arkansas, delaware, illinois, indiana, kansas, kentucky, maryland, missouri, nebraska, nevada, new jersey, new mexico, north carolina, ohio, oklahoma, pennsylvania, tennessee, virginia, west virginia and the district of columbia, or "zone b." additionally, unless covered in zone a or zone b, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 cx-7, and 2010-2015 cx-9 vehicles ever registered in the states of alaska, colorado, connecticut, idaho, iowa, maine, massachusetts, michigan, minnesota, montana, new hampshire, new york, north dakota, oregon, rhode island, south dakota, utah, vermont, washington, wisconsin, and wyoming or "zone c." these vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began november 9, 2018. Owners may contact mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317f.

Recall 18V6310002018Suspension:front:control arm

Mazda north american operations (Mazda) is recalling certain 2009-2010 Mazda Mazda6 vehicles sold, or ever registered in connecticut, delaware, illinois, indiana, iowa, kentucky, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, virginia, west virginia, wisconsin and the district of columbia. The front cross member may corrode after exposure to road salt.

Risk: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.

Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began march 18, 2019. Owners may contact mazda customer service at 1-800-222-5500 option 4. Mazda's number for this recall is 2818i.

Recall 18V0180002018Air bags:frontal:passenger side:inflator module Park it — do not drive

Mazda north american operations (Mazda) is recalling certain 2013 Mazda6 and cx-9 vehicles sold, or ever registered in the states of alabama, california, florida, georgia, hawaii, louisiana, mississippi, south carolina, texas, puerto rico, american samoa, guam, the northern mariana islands (saipan), and the u.s. Virgin islands or "zone a." additionally, unless covered in "zone a," Mazda is recalling certain 2010 Mazda6, cx-7 and cx-9 vehicles sold, or ever registered in the states of arizona, arkansas, delaware, district of columbia, illinois, indiana, kansas, kentucky, maryland, missouri, nebraska, nevada, new jersey, new mexico, north carolina, ohio, oklahoma, pennsylvania, tennessee, virginia, and west virginia or "zone b." additionally, unless covered in zone a or zone b, Mazda is recalling certain 2009 Mazda6, cx-7, and cx-9 vehicles ever registered in the states of alaska, colorado, connecticut, idaho, iowa, maine, massachusetts, michigan, minnesota, montana, new hampshire, new york, north dakota, oregon, rhode island, south dakota, utah, vermont, washington, wisconsin, and wyoming or "zone c." these vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began march 2, 2018. Owners may contact mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317f.

Recall 17V4290002017Air bags:frontal:passenger side:inflator module Park it — do not drive

Mazda north america operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 cx-7 and cx-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on august 30, 2017. Owners may contact mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317f. Note: this recall supersedes recall 16v356 and all vehicles that were not remedied under that campaign are now covered by this one.

Recall 16V5940002016Air bags:frontal:sensor/control module-inactive

Mazda north american operations (Mazda) is recalling certain model year 2009-2010 Mazda6 vehicles manufactured february 4, 2008, to december 3, 2009. The protective coating may not have been properly applied to the air bag control unit (acu) and, as a result, moisture may damage the unit causing it to malfunction.

Risk: Failure of the acu would illuminate the air bag warning light and prevent the air bags from deploying in the event of a crash, increasing the risk of injury.

Remedy: Mazda dealers will replace the acu, free of charge, however parts are not currently available. The recall began june 2017. Owners may contact mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9816h.

Recall 14V1140002014Fuel system, gasoline

Mazda north america operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured september 14, 2009, through may 2, 2011, and equipped with 2.5l engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.

Risk: Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.

Remedy: Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on april 30, 2014. Owners may contact mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214c.

Recall 13V4250002013Latches/locks/linkages:doors:latch

Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured february 4, 2008, through august 24, 2012. The door latch mounting screws may become loose.

Risk: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.

Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on october 29, 2013. Owners may contact mazda at 1-800-222-5500. Mazda's recall number is 7013i.

Recall 11V1340002011Fuel system, gasoline:storage:tank assembly

Mazda is recalling certain model year 2009-2010 Mazda6 vehicles manufactured from april 8, 2008, through february 8, 2010. A certain type of spider may weave a web in the evaporative canister vent line and this may cause a restriction in the line. If this occurs, the fuel tank pressure may become excessively negative when the emission control system works to purge the vapors from the canister.

Risk: As the canister is purged repeatedly during normal operation, the stress on the fuel tank may eventually result in a crack, potentially leading to fuel leakage ad an increased risk of fire.

Remedy: Dealers will inspect and clean up the canister vent line, and install a spring to prevent this type of spider from entering the vent line. This service will be performed free of charge. The safety recall is expected to begin on or before march 25, 2011. Owners may contact mazda customer assistance center at 1-800-222-5500.

Crash-test ratings (NHTSA)

VersionOverallFrontalSideRollover
2010 Mazda6 4-DR. w/SAB————

Other Mazda Mazda6 years

Frequently asked questions

Is the 2010 Mazda Mazda6 a reliable car?

Our score for the 2010 Mazda Mazda6 is 3.4/10 (avoid this year). It is based on 225 owner complaints and 9 recalls compared with other 2010 vehicles and other Mazda Mazda6 years.

What are the most common problems with the 2010 Mazda Mazda6?

Owners most often report problems with body & structure (60 complaints), airbags (54 complaints), suspension (43 complaints).

How many recalls does the 2010 Mazda Mazda6 have?

9 recalls are on file with NHTSA, including: 19V782000 (air bags:frontal:passenger side:inflator module); 18V717000 (air bags:frontal:passenger side:inflator module); 18V631000 (suspension:front:control arm).

Source: NHTSA complaints & recalls, EPA fueleconomy.gov. Data updated November 18, 2026. Complaints are unverified reports by owners.