Aug 29, 2024power train, vehicle speed control, engine1 injured
The engine in these cars are defective and can cause serious harm due to a part that was put inside the motor made of plastic. There was a lawsuit but if you didn’t get in on it you losses out for not knowing. I was recently at mercedes dealership to fix recalls and they brushed me off. The car can catch fire and I’m already experiencing engine failure after only owning the… Read more
The engine in these cars are defective and can cause serious harm due to a part that was put inside the motor made of plastic. There was a lawsuit but if you didn’t get in on it you losses out for not knowing. I was recently at mercedes dealership to fix recalls and they brushed me off. The car can catch fire and I’m already experiencing engine failure after only owning the car for a year. They don’t care because it’s an old car but it’s still being sold to unsuspecting buyers. I’m not the only one there are thousands of us who are at risk driving these cars because mercedes won’t admit their off the showroom floor mistake.
NHTSA complaint #11611501
Dec 30, 2023engine
Certain Mercedes-Benz models 2005- 2007 m272 v6 and m273 v8’s have faced or are facing issues regarding the balance sprocket in which drives the camshaft and crankshaft of the vehicle. Mercedes-Benz had made a decision to make certain engine components out of soft metals, when such metals are not adequate in handling the stress of the engine. In particular, in many cases, the… Read more
Certain Mercedes-Benz models 2005- 2007 m272 v6 and m273 v8’s have faced or are facing issues regarding the balance sprocket in which drives the camshaft and crankshaft of the vehicle. Mercedes-Benz had made a decision to make certain engine components out of soft metals, when such metals are not adequate in handling the stress of the engine. In particular, in many cases, the balance sprocket was made with inadequate materials and gradually deteriorated to the point in which it could not engage the timing chain and cause camshaft-crankshaft misalignment. I personally did not experience such failure yet but it is more of a concern as this is a common issue , the repair is quite substantial and the failure can damage the engine even more
NHTSA complaint #11562755
Oct 31, 2023engine
Engine codes p0016 and p0017 reads cam shaft and crank shaft correlation it is everywhere on the internet and on the mercedes benz forum.this is a know problem that mercedes has ignored. Its on all 2004 thru 2008 vehicles with the 3.5 engine. Calls for a balancer shaft replacement. This should definitely be a recall issue.the industry knows that is was poorly manufactured… Read more
Engine codes p0016 and p0017 reads cam shaft and crank shaft correlation it is everywhere on the internet and on the mercedes benz forum.this is a know problem that mercedes has ignored. Its on all 2004 thru 2008 vehicles with the 3.5 engine. Calls for a balancer shaft replacement. This should definitely be a recall issue.the industry knows that is was poorly manufactured part. Your help with rectifying this issue would greatly help the and restore the reputation of mercedes and restore faith in mercedes benz owners. My vehicle is a 2006 E350 4 matic with only 113,634 miles
NHTSA complaint #11552776
Dec 27, 2022engine
Driving the vehicle on several occasions on interstate 66 and the vehicle spontaneously went into limp mode. Now we find out it's a balance shaft issue and is a known problem from mercedes in the m272 engines for our 2006 E350 4-matic. They evidently used balance shafts with materials that were too soft, resulting in premature wearing of the balance shafts with all of the m272… Read more
Driving the vehicle on several occasions on interstate 66 and the vehicle spontaneously went into limp mode. Now we find out it's a balance shaft issue and is a known problem from mercedes in the m272 engines for our 2006 E350 4-matic. They evidently used balance shafts with materials that were too soft, resulting in premature wearing of the balance shafts with all of the m272 engines produced during this time having the problem. There was a previous class action lawsuit, which mercedes settled, however, the consumers were not adequately notified and no recall was ever issued for the cars. Now we have 2nd or 3rd owners having these problems that didn't get a notice and have no idea there is a huge expensive and dangerous problem with their vehicle. On I-66 traffic moves at 70 MPH (regular lanes) or 75 MPH (express lanes). Having the vehicle spontaneously go into limp mode because of this engine issue is dangerous and could have caused a fatal accident on multiple occasions for us. Mercedes should be recalling all of these engines and fixing them properly before someone gets injured or killed. When I spoke with mercedes, they said because I was not involved in the class action suit at that time, they were not willing to fix the car or pay for any portion of the repair, which they quoted me as costing $16,228.96. The problem is the mercedes went into limp mode on multiple occasions and there was no check engine light to indicate what the problem was for several months. We had n
NHTSA complaint #11499006
Dec 5, 2022engine
We just purchased a 2006 mercedes for our teenage sons and had a dealer look at it before we purchased it. They told us there were a couple of codes that were worth watching but that it wasn’t anything significant right now. After the car started jerking and shaking while driving it, we brought it in to dealership where they told us it had a common code for mercedes in this… Read more
We just purchased a 2006 mercedes for our teenage sons and had a dealer look at it before we purchased it. They told us there were a couple of codes that were worth watching but that it wasn’t anything significant right now. After the car started jerking and shaking while driving it, we brought it in to dealership where they told us it had a common code for mercedes in this timeframe p0016. Repair estimate is nearly $5000 to replace timing chain and balance shaft, or a new engine which would be roughly the same. After researching on my own upon being told this code, I found all of the information about the class action lawsuit and settlement, which of course we are too late to be a part of. The dealer said there is a potential that the car could just seize up at some point, so I don’t want my young sons to be out on the road when that happens. I am very frustrated and upset that this wasn’t a recall since it apparently affected a huge amount of vehicles manufactured within this time frame. There is a specific list of engines with known issues and ours is among them. Mercedes benz should be held responsible for making this right because it was definitely a quality issue. Now we are stuck with an unsafe vehicle, or a massive expense due to defect.
NHTSA complaint #11496136
Jun 5, 2022engine
Balance shaft issues possible cause of vehicle stalls and safety concerns.
NHTSA complaint #11467678
Jun 3, 2021engine
The crankshaft pulley is a two piece item. When excessive pressure is on it the pieces separate and disable the car. Upon replacing the belt or belt tensioner more pressure is exerted on the crankshaft pulley. Thus it fails and again disables the vehicle. When doing either of the replacement tasks mercedes fails to check this or mention it to customers. Thus months later… Read more
The crankshaft pulley is a two piece item. When excessive pressure is on it the pieces separate and disable the car. Upon replacing the belt or belt tensioner more pressure is exerted on the crankshaft pulley. Thus it fails and again disables the vehicle. When doing either of the replacement tasks mercedes fails to check this or mention it to customers. Thus months later it fails and previous belt replacement of belt tensioner replacement has to be done again. This creates a dual expense without fixing the issue the first time. Expense is in the thousands.
NHTSA complaint #11419514
Mar 18, 2021vehicle speed control, engine, forward collision avoidance
I need help with my crankshaft please I see a lot of people are having the same problem
NHTSA complaint #11403793
Nov 9, 2020steering, service brakes, engineCrash
Tl* the contact owns a 2006 mercedes benz E350. The contact stated that while driving 45 MPH, a warning message of 'restricting system manufacture' illuminated and 07:02 the vehicle lost all power. The contact lost control of the steering, and the brakes failed. As a result, the contact crashed into a wall at 8-10 MPH, but did not sustained injuries. The vehicle was restarted… Read more
Tl* the contact owns a 2006 mercedes benz E350. The contact stated that while driving 45 MPH, a warning message of 'restricting system manufacture' illuminated and 07:02 the vehicle lost all power. The contact lost control of the steering, and the brakes failed. As a result, the contact crashed into a wall at 8-10 MPH, but did not sustained injuries. The vehicle was restarted and was able to drive normal however, the failure recurred while driving. The vehicle was towed to the contacts residence. The contact called an unknown dealer and informed them of the failure and was provided with the number to NHTSA. The vehicle was not taken to a dealer and was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 125,663.
NHTSA complaint #11373780
Feb 20, 2020service brakes, engine, fuel/propulsion system
This vehicle is a threat to my health with all the problems I'm having with it. I have to press extra had to stop . Had brakes checked and there was no problem. There is a bad gasoline leak and loud smell of gas when I fill up. Looked under rear seat and saw gas on gas tank. Dried gas up and the big puddle returned. Can I drive this car? I need someone to tell me what to do.… Read more
This vehicle is a threat to my health with all the problems I'm having with it. I have to press extra had to stop . Had brakes checked and there was no problem. There is a bad gasoline leak and loud smell of gas when I fill up. Looked under rear seat and saw gas on gas tank. Dried gas up and the big puddle returned. Can I drive this car? I need someone to tell me what to do. The last and most worrisome thing to me is that there are 2 dtc codes coming up causing the check engine light to come on. Had mechanic to clear then but they come right back when car is started. I need to get this car inspected. Someone tell me what to do. Mechanic said that the code indicate a problem with the engine and that it might take $8700 to repair every thing. I dont have that type of money. This is the car makers problem. Who is looking out for me. Is the goverment doing there job when it comes to this car. Heard there are more cars like this. Oh this is a 2006 mercedes E350. Will the goverment, dealer or manufacturer buy this car from me. This is a plea for help from anywhere. They say there is a recall on this car but when it came out there was 1 year left on car warranty before it ran out. The car didn't quit running when the stalling to repair these cars took place. Some one is in someones back pocket. Someone needs to do their job and get this problem taken care of once and for all. You may lose some friends in the process but this is better than someone losing their life. This vehicle h
NHTSA complaint #11310454
Feb 12, 2020power train, engine
2006 mercedes ml350 balance shaft - class action lawsuit - defective. Went into low gear while running. Will not come back to normal. Code from diagnosis states the problem as timing chain. Mercedes states " maybe fixed in good faith" . Bad balance shaft from factory. Many problems with this defective part. But we need money up front to fix which we don't have. From mercedes repair shop.
NHTSA complaint #11308851
Jan 16, 2020engine, fuel/propulsion system
Car had quarter tank when bought. Drove out gas and put about another quarter tank of gas in. Drove this out. Smelled no fumes. Filled tank up. Have smelled loud gas smell for 1 week now.
NHTSA complaint #11299956
Dec 4, 2019engine, fuel/propulsion system
Regardless of vehicle movement gas leak from fuel tank located under back seat above exhaust system. Constant gas smell, and fuel gauge always jumping up and down again regardless of motion. Check engine lights indicate faulty coolant temperature sensor, and faulty fuel level sensor. Dealership is refusing to cover tank assembly replacement under pzev warranty of 15yrs /… Read more
Regardless of vehicle movement gas leak from fuel tank located under back seat above exhaust system. Constant gas smell, and fuel gauge always jumping up and down again regardless of motion. Check engine lights indicate faulty coolant temperature sensor, and faulty fuel level sensor. Dealership is refusing to cover tank assembly replacement under pzev warranty of 15yrs / 150,000 miles in state of california. Vehicle is 2006, with 109k miles. Documentation of trouble codes not available at time of reporting, but can be provided upon future request. Fuel runs down the side of the tank narrowly missing the exhaust, potential fire hazard.
NHTSA complaint #11286778
Jul 4, 2019steering, service brakes, engine
Takata recall. ABS malfunction, brake sensor
NHTSA complaint #11229475
Jun 15, 2019engine
Mercedes-Benz v6 m272 engines have timing chain problems caused by balance shaft failures which mercedes has known about for year. Faulty gears wear out prematurely, excessively, and without warning, causing the vehicle to malfunction, the 'check engine light' to remain illuminated, and the vehicle to misfire or stop driving. Weak materials were used for the balance shaft… Read more
Mercedes-Benz v6 m272 engines have timing chain problems caused by balance shaft failures which mercedes has known about for year. Faulty gears wear out prematurely, excessively, and without warning, causing the vehicle to malfunction, the 'check engine light' to remain illuminated, and the vehicle to misfire or stop driving. Weak materials were used for the balance shaft sprockets and the timing chain guide, mercedes never contacted its owners about the defect which can cause the engine to halt and the car to stop mid-traffic. The check engine light comes on the vehicle at every start, throwing a p0016 and p0017 trouble code, which returns even after clearing and restart. After going to several mechanics, all have noted that the balance shaft (within the engine) requires repair an issue mercedes has know about for several years, and had even issued its mechanics with service bulletins (april 23, 2009, see attached), but has never notified its car owners of the hazardous driving during any of its service at the dealership or has not notified with any other communication. Engines with serial numbers lower than m272 engine serial no. 2729..30 468993 have the defective parts at manufacture, which is affecting my mercedes vehicle.
NHTSA complaint #11220256
May 9, 2019engineFire
I arrived home after driving 2 miles from work and when I stopped I saw smoke coming from the engine. I turned off the car and opened the hood. The smoke would almost stop and then become thick again, in cycles of about 1 minute. The smoke was coming from the cooling fan. After several cycles it burst into flames. Fortunately we were ready with a fire extinguisher and put… Read more
I arrived home after driving 2 miles from work and when I stopped I saw smoke coming from the engine. I turned off the car and opened the hood. The smoke would almost stop and then become thick again, in cycles of about 1 minute. The smoke was coming from the cooling fan. After several cycles it burst into flames. Fortunately we were ready with a fire extinguisher and put the fire out right away. The fuse, which I believe should have popped and stopped the cycling of the fan, never did blow. I bought my car used but it only has 50,000 miles on it. All information in the carfax indicates it was maintained. I didn't take pictures of the fire.
NHTSA complaint #11206623
Jun 12, 2018engine, fuel/propulsion system
Fuel pump leaking fumes (and fuel?). While parked and preparing to come home the fuel pump failed and the car refused to start. It will not be repaired unless it is under the extended warranty. I am trying to learn if it will be covered under a extended warranty.
NHTSA complaint #11101525
Mar 7, 2018electrical system, exterior lighting, engine
Check light
NHTSA complaint #11076585
Dec 16, 2017engine
I have check engine light on, nobody "mechanic" know to fix this problem. I have codes: 1-p0016 2-p0017 3-p2195 4-p2198 5-p0171 6-p0174
NHTSA complaint #11055077
Oct 31, 2017engine
Timing belt sprocket lost teeth on it due to it not being strong enough dealer need to replace this part since it part of engine this part should not be giving it like this
NHTSA complaint #11041513
Oct 10, 2017service brakes, engineCrash
Tl* the contact owned a 2006 Mercedes-Benz e350w. While driving 30 MPH, the vehicle stalled without warning and the brakes failed to stop the vehicle. As a result, the contact rear ended the preceding vehicle. The air bags deployed. There were no injuries. A police report was filed. The contact's vehicle was towed from the scene to Mercedes-Benz of ontario (3787 e guasti rd,… Read more
Tl* the contact owned a 2006 Mercedes-Benz e350w. While driving 30 MPH, the vehicle stalled without warning and the brakes failed to stop the vehicle. As a result, the contact rear ended the preceding vehicle. The air bags deployed. There were no injuries. A police report was filed. The contact's vehicle was towed from the scene to Mercedes-Benz of ontario (3787 e guasti rd, ontario, ca 91761), but was not diagnosed. The contact's insurance company confirmed that the vehicle was destroyed. The manufacturer was not made aware of the failure. The approximate failure mileage was 143,000.
NHTSA complaint #11032799
Oct 7, 2017engineCrash2 injured
My 2006 mercedes benz 350 e series had gotten in a accident due to the car stalling out. I have a code reader and will provide the necessary pictures I took the day prior of the accident.
NHTSA complaint #11032152
Jun 13, 2017service brakes, engine
Tl* the contact owns a 2006 Mercedes-Benz E350. While driving 5 MPH, the vehicle stalled and the stop braking system warning indicator illuminated and flashed. The vehicle was towed to an independent mechanic, but was not diagnosed or repaired. The vehicle was taken to a local Mercedes-Benz dealer (located at 404 pennsylvania in pa 19034 866-383-0881) where it was diagnosed,… Read more
Tl* the contact owns a 2006 Mercedes-Benz E350. While driving 5 MPH, the vehicle stalled and the stop braking system warning indicator illuminated and flashed. The vehicle was towed to an independent mechanic, but was not diagnosed or repaired. The vehicle was taken to a local Mercedes-Benz dealer (located at 404 pennsylvania in pa 19034 866-383-0881) where it was diagnosed, but the failure could not be duplicated. The manufacturer was made aware of the failure and referred the contact to the dealer regarding the spc pump. The failure mileage was 101,000.
NHTSA complaint #10994921
May 11, 2017engine
I have a benz E350 2006 with 60k miles. My check engine light went on and I was told it was the balance shaft gear problem. Mercedes-Benz had a class action lawsuit complaint filed for this issue for some of their cars with this problem as well as faulty engines & idle gears. There are more than 100000 cars from 2005 to 2007 model years with this problem and they managed to… Read more
I have a benz E350 2006 with 60k miles. My check engine light went on and I was told it was the balance shaft gear problem. Mercedes-Benz had a class action lawsuit complaint filed for this issue for some of their cars with this problem as well as faulty engines & idle gears. There are more than 100000 cars from 2005 to 2007 model years with this problem and they managed to get away without issuing a recall. What surprises me is even with the class action suit, they pay only 30% of the repair cost. Dealership estimate for this repair is $7500. They have to remove the entire engine/motor and open it up to replace the small part. Http://www.classactionrebates.com/settlements/mercedes_engine/ you are a member of this class action if you purchased or leased Mercedes-Benz vehicles in the united states that are model years 2005-2007 equipped with m272 (v6) or m273 (v8) engines bearing serial numbers up to 2729..30 468993 or 2739 ..30 088611, respectively. You can verify your serial number by checking your past repair orders. Class members may also enter the vehicle identification number (VIN) on the settlement website to see if their vehicle qualifies for benefits from this mercedes class action settl I now have to replace the balance shift gears so my car will pass emissions inspection. Mercedes benz is not worth buying. Mercedes benz needs to be responsible for faulty equipment. Mercedes benz does not have the reputation it used to have.
NHTSA complaint #10984808
Mar 27, 2017service brakes, engine, fuel/propulsion system
Strong fuel smell coming from the outside of vehicle
NHTSA complaint #10968816
Feb 9, 2017engineFire
I went to a hardware store and parked the car in the store parking lot. About 10 minutes later somebody came in and asked me if I was driving a silver mercedes; I told him yes and he told me that it was on fire. When I got out of the store I saw my car's engine compartment on fire. By the time the fire department arrived on the scene the whole engine compartment had been… Read more
I went to a hardware store and parked the car in the store parking lot. About 10 minutes later somebody came in and asked me if I was driving a silver mercedes; I told him yes and he told me that it was on fire. When I got out of the store I saw my car's engine compartment on fire. By the time the fire department arrived on the scene the whole engine compartment had been gutted and the fire had spread to another car which was parked infront of mine.
NHTSA complaint #10953767
Dec 8, 2016engine
The engine light indicator came on and was checked at the dearlership and showed to replace shaft. It seemed a lot of problems with same indication. Cost to repair was quoted at $5,500.
NHTSA complaint #10933893
Aug 3, 2016steering, power train, traction control system, service brakes, engine
Tl* the contact owns a 2006 Mercedes-Benz E350. While driving approximately 45 to 50 MPH, the vehicle approached a ramp and applied the brakes. Messages on the instrument panel illuminated that read "reduced brake pressure and depress brake fully", "traction control", "ABS", and "check engine lights". In addition, the steering wheel locked up when the brakes were applied. The… Read more
Tl* the contact owns a 2006 Mercedes-Benz E350. While driving approximately 45 to 50 MPH, the vehicle approached a ramp and applied the brakes. Messages on the instrument panel illuminated that read "reduced brake pressure and depress brake fully", "traction control", "ABS", and "check engine lights". In addition, the steering wheel locked up when the brakes were applied. The vehicle was pulled over, turned off, restarted, and driven home. The failure recurred. The vehicle was driven to a mechanic who diagnosed that the transmission and engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the issue. The approximate failure mileage was 129,000.
NHTSA complaint #10892942
Jul 21, 2016engine
Engine jerks and sputters while driving. I appears that the vehicle will shutdown immediately. Cannot drive over 25 MPH or go up hills.
NHTSA complaint #10887574
May 9, 2016engine
Check engine light goes on....car vibrates (shakes!) ...I pull over, stop the car, turn off the engine and the problem does not occur again ...in ten years this episode has occurred three or four times. I brought it in the a local mbz warranty facility and they could not find anything wrong...and the problem did not happen again until 2 weeks ago when I brought it to a… Read more
Check engine light goes on....car vibrates (shakes!) ...I pull over, stop the car, turn off the engine and the problem does not occur again ...in ten years this episode has occurred three or four times. I brought it in the a local mbz warranty facility and they could not find anything wrong...and the problem did not happen again until 2 weeks ago when I brought it to a different mechanic who was able to diagnose the probem as the "intake manifold actuator linkage broken" mercedes benz USA will not pay to repair it...my mechanic in san diego said I was the eigth car mbz 2005 to 2007 that has had the same issue. The vehicle was in motion when the shaking occurred. It happened both on highway and street ...I was not turning.
NHTSA complaint #10863940
Oct 5, 2015air bags, structure, engineCrash7 injured
I am reporting a very serious, disturbing, shocking and tragic accident on 9/12/2015 on randall road in elgin, il USA at 2:35 pm just after big timber road signal.my southbound 2006 mercedes benz E350 car was hit by the high speed out of control northbound 2014 toyota corolla, which had crossed/swerved the center line and resulted in a head on collision/crash.....updated 10-27-15 *bf *js
NHTSA complaint #10779783
Sep 27, 2015electronic stability control (esc), engine
The engine of my car stalled suddenly, braking power was reduced dramatically. I was about to get into a serious crash but likely this happened in a local street at a traffic light when everyone was ready to slow down and stop. My dealer told me the engine stalled due to a broken vacuum intake manifold linkage which controls air in and out in the system. The only way to fix is… Read more
The engine of my car stalled suddenly, braking power was reduced dramatically. I was about to get into a serious crash but likely this happened in a local street at a traffic light when everyone was ready to slow down and stop. My dealer told me the engine stalled due to a broken vacuum intake manifold linkage which controls air in and out in the system. The only way to fix is to replace the entire manifold ($2100) and mercedes benz does not offer an extended warranty on this component. I was surprised with the quality of mb especially when I checked the internet to find out hundreds with the same incident and with many unpleasant customers. The broken intake manifold linkage is 100% design issue. My car has 107k miles, I had my extended warranty up until 100k, so I can't believe these 7k miles caused this linkage to be broken. It is a design issue (probably cheap plastic part that aged over time). Mb had several extended warranty on other major components such as: gas tank ($2,400) and sbc pump ($2,000) due to fatal incidents, so I am not sure how many people have to die in car crashes before mb offers this extended warranty. I can't believe I am saying this about mb quality, but just go online and you will find out more and more about these issues. The problem with this component is the fact that it is unpredictable because it depends on the position of these flabs (closed, semi opened, opened position). Which makes it scary to drive the car when you know that this may happ
NHTSA complaint #10777922
Aug 16, 2015unknown or other, engine, fuel/propulsion system
For several times now I can smelling a strong odor of gasoline inside and outside of the car, even more so after pumping gas on the car. Sometimes I can see a small leak into the parking space.
NHTSA complaint #10749010
Mar 19, 2015power train, engine, fuel/propulsion system
There is a serious safety issue with 2006 Mercedes-Benz e class (mbec) because of a manufacturer's and/or design defect which causes this vehicle to not go into proper gear and/or stall suddenly putting the public at risk. I barely escaped being smashed into by oncoming traffic while making a routine left hand turn into a gas station because my mbec was stuck in gear and did… Read more
There is a serious safety issue with 2006 Mercedes-Benz e class (mbec) because of a manufacturer's and/or design defect which causes this vehicle to not go into proper gear and/or stall suddenly putting the public at risk. I barely escaped being smashed into by oncoming traffic while making a routine left hand turn into a gas station because my mbec was stuck in gear and did not accelerate as it was manufactured and designed to do but rather sputtered at less than 5 miles per hour (MPH). The only reason I was not t-boned and likely seriously injured along with other people was because the other drivers swerved into oncoming traffic causing those drivers to also swerve. Miraculously no one was injured, this time. Also, the reason why I was turning into the gas station was because I was forced to get off the highway because my mbec would not change gear after I got on the highway and was approaching red-lining at and it seemed like the engine might blow. The tiptronic also failed during this malfunction. I had the authorized mb dealer that I have used since I purchased my mbec pickup my vehicle to look into this issue and my advisor told me I needed a new balance shaft because the one in my vehicle had prematurely worn (even though I have always stringently followed my mb advisor's suggestions) and it would cost roughly $6,500. S/he also said this occurs in roughly 15-20% of '06 mbec. But mb would not fix this safety defect unless I paid. Worse yet, my advisor never made
NHTSA complaint #10695497
Dec 22, 2014engine
Gearing mechanism suddenly failed while driving thus causing the vehicle to stall. Was unable to move forward until the car was shut off, restarted and then car moved forward with a very jerky motion situation posed a dangerous hazard to passengers as well as other vehicles in the flow of traffic. *tr
NHTSA complaint #10667549
Dec 20, 2014engine
Balance shift worned
NHTSA complaint #10667431
Dec 11, 2014engine
Tl* the contact owns a 2006 mercedes benz E350. While driving approximately 45 MPH, the vehicle jerked, stalled, and the check engine warning light illuminated. In order for the vehicle to be restarted, the key had to be taken out of the ignition and re- inserted. The failure recurred on numerous occasions. The vehicle was taken to a dealer. The technician diagnosed that the… Read more
Tl* the contact owns a 2006 mercedes benz E350. While driving approximately 45 MPH, the vehicle jerked, stalled, and the check engine warning light illuminated. In order for the vehicle to be restarted, the key had to be taken out of the ignition and re- inserted. The failure recurred on numerous occasions. The vehicle was taken to a dealer. The technician diagnosed that the balance shift and crank shaft needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 87,000.
NHTSA complaint #10663580
Dec 2, 2014power train, engine
Check engine light comes on and when check indicates cam sensor problem. I was told that mercedes knows about this problem. *js
NHTSA complaint #10661824
Nov 10, 2014engine
Po16, po17 needs to replace balanceshaft timing chain will cost 8-10k. Engine will fail if not replaced . There is a notice on this. Check engine light stays on. Mercedes refuse to pay , cover cost when it is manufacturer defect. The engine should last longer. *tr
NHTSA complaint #10653970
Oct 18, 2014engine
Balance shaft manufacturing defect causes gear teeth to wear prematurely. This is a internal engine component. Poor materials caused the camshaft sprocket teeth to wear out ? Thus this is a manufacturing problem. Internal engine components like balance shaft sprockets are meant to last at least 150000 miles on mb cars ? Thus they are difficult to replace & repairs so… Read more
Balance shaft manufacturing defect causes gear teeth to wear prematurely. This is a internal engine component. Poor materials caused the camshaft sprocket teeth to wear out ? Thus this is a manufacturing problem. Internal engine components like balance shaft sprockets are meant to last at least 150000 miles on mb cars ? Thus they are difficult to replace & repairs so expensive. Symptom starts with camshaft position related check engine light - repair costs $7000. This occurs for many many many cars with that m272 engine. This is a environmental and safety hazard. Mercedes should be forced to do a recall. Ref: http://mbworld.org/forums/e-class-w211/442004-dreaded-m272-balance-shaft.html ref: http://mbworld.org/forums/c-class-w203/376585-p0016-p0017-camshaft-position-sensor-location-please-help.html. *tr
NHTSA complaint #10648574