CarProblemsDB

2000 Ford Ranger brakes problems

78 owners reported brakes problems — 12% of all 670 complaints about the 2000 Ford Ranger.

Brakes complaints by Ford Ranger year

20262
20257
20247
20233
20223
202115
20209
201920
20118
20105
20096
20082
20072
20065
200510
200424
200337
200223
200155
200078

What owners report

Oct 5, 2016service brakes, hydraulic

Tl* the contact owns a 2000 Ford Ranger. While driving approximately 30 MPH, the brake pedal was depressed, but the vehicle failed to slow down. The vehicle was pulled over to the side of the road and parked. The vehicle was towed to the dealer where it was diagnosed that the master cylinder failed. The vehicle was repaired. The manufacturer was not notified. The approximate failure mileage was 42,000.

NHTSA complaint #10914010
Oct 25, 2015suspension, power train, service brakesCrash

My frame is rusted out, 110,000, miles, replaced transmission, brake lines, gas lines, and a # of other things, due to a rusted out under carriage, the motor is great, things on the frame are breaking off all the time, so much rust cant even see a bolt.

NHTSA complaint #10785831
Oct 20, 2015service brakes

Tl* the contact owns a 2000 Ford Ranger. While driving approximately 35 MPH, the brakes made an abnormal noise and hesitated to stop the vehicle when the pedal was depressed. The failure recurred numerous times. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 143,000.

NHTSA complaint #10783765
Aug 21, 2014structure, service brakes
Vehicle has exhibited severe frame and underbody rust for several years; during last inspection mechanic cautioned that vehicle was badly rusted but still able to pass inspection. I visually inspected the vehicle this evening and found severe delamination to frame members and severe rusting of bed underframe. Crossmember supporting bed is rusted through or non-existent in… Read more

Vehicle has exhibited severe frame and underbody rust for several years; during last inspection mechanic cautioned that vehicle was badly rusted but still able to pass inspection. I visually inspected the vehicle this evening and found severe delamination to frame members and severe rusting of bed underframe. Crossmember supporting bed is rusted through or non-existent in approximately 40% of surface area. Shock absorber mounts, leaf spring mounts, fuel tank supports, and fuel lines significantly rusted. Approximately one year ago rear brake lines failed at low speed and vehicle nearly collided with parked cars and adjancent stone wall. Mechanic attributed brake failure to rust through of rear brake system. Vehicle was purchased new and is still owned by original owner. Vehicle has been maintained since new and properly cared for. *tr

NHTSA complaint #10627290
Apr 22, 2014suspension, service brakes, hydraulic, structure

Tl* the contact owns a 2000 Ford Ranger. The contact stated that upon inspection, it was found that the rear leaf springs had failed. The vehicle was taken to a private mechanic where the failure was confirmed. The vehicle was not repaired. The failure mileage was 124,000. Updated 07/01/14 ma the consumer also stated three brake lines failed, the tailgate failed and the rear bumper rusted out.

NHTSA complaint #10584245
Nov 4, 2013service brakesCrash
Brakes fail at slow speeds. Sometimes they work, some times they start working and quit and the truck slides. No ABS lights coming on and the ABS doesn't pump. Slid into parking curb stop, almost struck oreilly auto parts building in atchison and jammed my neck. Had brakes checked, master cylinder replaced and brakes were bled with new fluid. Every thing in good shape, but… Read more

Brakes fail at slow speeds. Sometimes they work, some times they start working and quit and the truck slides. No ABS lights coming on and the ABS doesn't pump. Slid into parking curb stop, almost struck oreilly auto parts building in atchison and jammed my neck. Had brakes checked, master cylinder replaced and brakes were bled with new fluid. Every thing in good shape, but brakes are still failing. Mechanic in atchison said this is the second Ranger he seen with this problem; on the other Ranger they removed the ABS fuse and brakes functioned fine. Was told there were no codes or ABS lights on vehicle until fuse was pulled. With no codes being set, unable to figure out this problem. Ford not willing to instruct as to what is going on without charging $80 an hour for repairs. Have limited income, can not afford to take vehicle to Ford. Vehicle is dangerous is going to cause a collision. Please help. *tr

NHTSA complaint #10550855
Feb 1, 2012suspension, service brakes, hydraulic, structure
There is a lot of frame rust on my truck. Especially where the frame connects to the bed. I had to replace both the rear spring shackle brackets, both broke off because of rust. Twice there was a hole in the brake line, luckily I saw this when the car was parked and now while I was driving which could have been very dangerous. The rear bumpers paint has peeled off and the now… Read more

There is a lot of frame rust on my truck. Especially where the frame connects to the bed. I had to replace both the rear spring shackle brackets, both broke off because of rust. Twice there was a hole in the brake line, luckily I saw this when the car was parked and now while I was driving which could have been very dangerous. The rear bumpers paint has peeled off and the now is very rusty and it could fall off at anytime. *tr

NHTSA complaint #10446117
Sep 5, 2011service brakes, hydraulic

Brake pedal would go to the floor and hit back plate with initial brake activation. Dealer replaced master cylinder assembly. *tr

NHTSA complaint #10423768
Sep 5, 2011service brakes, hydraulic
Brake pedal on initial press would go to the floor and hit the back stop. A pump would create some pressure but a hard press would still hit the back stop. Dealer confirmed loss of pressure and replaced master cylinder. This is the third on this truck. Previous owner replace master cylinder once and this is the 2nd replacement since I have owned the vehicle. I replaced… Read more

Brake pedal on initial press would go to the floor and hit the back stop. A pump would create some pressure but a hard press would still hit the back stop. Dealer confirmed loss of pressure and replaced master cylinder. This is the third on this truck. Previous owner replace master cylinder once and this is the 2nd replacement since I have owned the vehicle. I replaced the master cylinder previously at 96,836 miles. *tr

NHTSA complaint #10423770
Apr 18, 2011suspension, service brakes, hydraulic, structure
I have a 2000 Ford Ranger xlt. The frame, brake lines, shackles, shocks, and other components from the mid frame to the rear of the vehicle are showing severe signs of rust and rot. The rear brake lines were rotted through and required replacement. The rear bumper has rotted completely off the frame on the drivers side. The rear shackles, spring mounts, differential cover… Read more

I have a 2000 Ford Ranger xlt. The frame, brake lines, shackles, shocks, and other components from the mid frame to the rear of the vehicle are showing severe signs of rust and rot. The rear brake lines were rotted through and required replacement. The rear bumper has rotted completely off the frame on the drivers side. The rear shackles, spring mounts, differential cover and axle are showing severe signs of rust, and in some areas, complete rot through. The vehicle has approximately 71,000 miles and is otherwise in very good condition. As I research this problem, I have found others with the same problems. These issues revolve around the safety components of the vehicle and in short time, this vehicle will likely be unsafe to drive. The vehicle is only 11 years old and in my opinion, the safety of the vehicle should not be compromised this drastically after only 11 years. I would urge Ford motor company to consider launching an investigation before a serious issue happens. *tr

NHTSA complaint #10396619
May 11, 2010service brakes, hydraulic
Tl*the contact owns a 2000 Ford Ranger. While inspecting the vehicle, the contact noticed that the rear passenger side brake line was rubbing against the shocks and the metal bracket that held the rear passenger side brake line separate was missing. The contact spoke with the dealer who advised him that no such part existed; the contact, however, found the part on the… Read more

Tl*the contact owns a 2000 Ford Ranger. While inspecting the vehicle, the contact noticed that the rear passenger side brake line was rubbing against the shocks and the metal bracket that held the rear passenger side brake line separate was missing. The contact spoke with the dealer who advised him that no such part existed; the contact, however, found the part on the manufacturers website. The vehicle had not been repaired at the time of the complaint. The current and failure mileages were approximately 92,000.

NHTSA complaint #10329970
Oct 14, 2009vehicle speed control, service brakes, electric

ABS light (orange) always on, 2000 Ford Ranger. Also received recall for cruise but not ABS. *tr

NHTSA complaint #10287325
May 23, 2009service brakes, hydraulic, vehicle speed control

I have a 2000 Ford Ranger xlt 3.0 liter at 39,000 miles my antilock brakes went out. They stop working and made my stops during bad weather more dangerous. My speedometer and odometer stop working at around 64,000 miles and was not able to afford the repair. I have been calculating the speed over the past 7 years and the mileage. *tr

NHTSA complaint #10269797
Oct 16, 2008service brakes, hydraulic, power train
Tl*the contact owns a 2000 Ford Ranger. While driving 65 MPH, the vehicle suddenly stopped accelerating. The transmission shifted into neutral and the ABS indicator illuminated on the instrument panel. If the contact immediately activates the hazard lights, the failure will correct itself. The failure has occurred more than 30 times within one month. The vehicle has not… Read more

Tl*the contact owns a 2000 Ford Ranger. While driving 65 MPH, the vehicle suddenly stopped accelerating. The transmission shifted into neutral and the ABS indicator illuminated on the instrument panel. If the contact immediately activates the hazard lights, the failure will correct itself. The failure has occurred more than 30 times within one month. The vehicle has not been diagnosed by the dealer. The current mileage was 86,000 and failure mileage was 85,000. Updated 11/12/08 *cn updated 11/18/08. *jb

NHTSA complaint #10245661
Jul 14, 2008service brakes, hydraulic
Tl*the contact owns a 2000 Ford Ranger. While driving 10 MPH after accelerating from a stop, the contact made an abrupt stop and the brakes failed. She drove home at a low speed and, once there, she noticed brake fluid pumping out of the brake lines. The vehicle was towed to a local muffler shop the following day. The contact was informed that the brake lines had corroded… Read more

Tl*the contact owns a 2000 Ford Ranger. While driving 10 MPH after accelerating from a stop, the contact made an abrupt stop and the brakes failed. She drove home at a low speed and, once there, she noticed brake fluid pumping out of the brake lines. The vehicle was towed to a local muffler shop the following day. The contact was informed that the brake lines had corroded through the passenger side rear brake lines. No repairs have been made because the parts have not yet arrived. The failure and current mileages were 50,170.

NHTSA complaint #10234155
Jul 12, 2008service brakes, hydraulic
2000 Ford Ranger brake line failure -- the right-rear brake line ruptured. This is the second brake line rupture in a little over 1 year. The first rupture was with the left-rear brake line in march 2007. The cost of the repair was $295.00. The second rupture occurred on july 2, 2008. This repair has not been performed as yet. Both ruptures occurred without warning and… Read more

2000 Ford Ranger brake line failure -- the right-rear brake line ruptured. This is the second brake line rupture in a little over 1 year. The first rupture was with the left-rear brake line in march 2007. The cost of the repair was $295.00. The second rupture occurred on july 2, 2008. This repair has not been performed as yet. Both ruptures occurred without warning and during an attempt to apply the brakes. Upon applying the brakes, the pedal went spongy, and both the brake warning light and ABS warning light came on. The vehicle did eventually stop. Fortunately, there where no other vehicles or pedestrians in front of me. Upon initial inspection, the brake line was leaking fluid and the master brake cylinder reservoir was below half full. A closer inspection revealed that the brake line had rusted through near the fittings. This vehicle has approximately 34,000 miles and is driven infrequently. *tr

NHTSA complaint #10234050
Jan 4, 2005steering, service brakes, hydraulicCrash1 injured
I was driving on a secondary road at approximately 35 - 40 MPH and as I came to the crest of a downhill section, I lightly touched the brakes due to snow on the road. The truck veered violently to the left and went into a skid. I corrected and again lightly touched the brakes and the truck again veered violently to the left and I was unable to correct before the truck left… Read more

I was driving on a secondary road at approximately 35 - 40 MPH and as I came to the crest of a downhill section, I lightly touched the brakes due to snow on the road. The truck veered violently to the left and went into a skid. I corrected and again lightly touched the brakes and the truck again veered violently to the left and I was unable to correct before the truck left the roadway and struck a large tree stump. The truck is awaiting insurance adjustment decision on repair.*ak

NHTSA complaint #10105739
Dec 31, 2003service brakes, hydraulicCrash

When pressing on the brake to make a quick stop on dry pavement, the brake pedal bent approximately 15 degrees preventing me from stopping in time to avoid hitting the car in front of me. The truck did not skid nor did the the anti-lock brake systems activate.

NHTSA complaint #10051427
Sep 22, 2003service brakes, hydraulicCrash2 injured

Two minor accidents and several near accidents due to antilock brake failure, requested dealer look into problem, they said pads are the problem, pads were replaced two months ago. Independent mechanic confirmed that antilock was non functional. *jb

NHTSA complaint #10039273
Jan 2, 2002parking brakeCrash

Park brake does not always release on right rear tire. While driving 30-35 MPH right rear tire locked up, vehicle started to skid and hit a bridge. Vehicle not taken to dealer yet.*ak

NHTSA complaint #8001355
Apr 25, 2001service brakes, hydraulicCrash

Vehicle had come to a complete stop, consumer kept foot on brake, vehicle rolled forward and rear ended vehicle in front, brakes had failed. Towed to dealer, who found brake system contaminated with motor oil. Dealer refused to honor warranty, stated consumer must have put motor oil in brake line.*ak

NHTSA complaint #886793
Apr 12, 2001service brakes, hydraulic, air bagsCrash

Vehicle rear ended antoher vehicle and at speed of 20 MPH, and both passenger's side and driver's side airbags did not deploy. Also, when attempting to stop prior to collision anti-lock brakes locked up. *ak

NHTSA complaint #885812
Jan 14, 2001steering, service brakes, hydraulic, air bagsCrash1 injured
Driving 60mph on interstate pheasant flew low in front of verhicle, as the pheasant disapeared in from my view the truck did an abrupt swirve to the left, I had no steering control, the truck went from the right lane accross passing lane and hit head on into flat concrete berrier, the air bags did not deploy, over $9,000 in damage including new frame. When the truck was being… Read more

Driving 60mph on interstate pheasant flew low in front of verhicle, as the pheasant disapeared in from my view the truck did an abrupt swirve to the left, I had no steering control, the truck went from the right lane accross passing lane and hit head on into flat concrete berrier, the air bags did not deploy, over $9,000 in damage including new frame. When the truck was being hoisted onto rollback I noticed that the tie rod was hanging. The yoke where the tie rod is bolted to (cast iron) was broken off and I noticed a lot of pheasant remains on the tierod and suspension. I am very concerned that a small bird as this would cause the cast iron yoke to break, also why my airbags did not deploy. The front tire and rim did not impact the concrete berrier. When I saw the pheasant I did not react to it, I did not turn the wheel or hit the brakes, this may sound funny but the truck swirved left dirrectly into the berrier. The seat belt saved me from serious injury. My main concern is the pc that the tie rod mounts to and no air bag deployment *ak

NHTSA complaint #739339
Jan 3, 2001service brakes, hydraulicCrash

When brakes were applied under normal conditions pedal went to the floor, causing extended stopping distance, and once resulting in a collision. Dealer has inspected brakes, and was not able to duplicate or correct problem. Dealer changed brake booster. *ak

NHTSA complaint #877317
Dec 7, 2000service brakes, hydraulic1 injured

Brakes failed causing a crash, the consumer was injured in the accident, consumer believes the tires were also the cause (unable to verify). *slc

NHTSA complaint #557960
Aug 18, 2000service brakes, hydraulicCrash1 injured

The brakes did not stop the vehicle at all.

NHTSA complaint #728404
← All 2000 Ford Ranger problems & recalls