CarProblemsDB

2001 Toyota Tundra brakes problems

118 owners reported brakes problems — 28% of all 416 complaints about the 2001 Toyota Tundra.

Brakes complaints by Toyota Tundra year

20257
202427
202332
202232
20204
20199
201822
201714
201634
201510
20147
20134
20127
201110
201019
20091
200829
200733
200634
200543
200437
200341
2002120
2001118
2000282

What owners report

Nov 8, 2017structure, service brakes

2001 Toyota Tundra. Consumer writes in regards to broken cross member. *ld the consumer stated the spare tire mount fell off,the rear shock top failed and the crossmember failure caused the brake line to fail. Updated 11/08/2017*js

NHTSA complaint #11043528
Aug 16, 2016suspension, power train, service brakes
I purchased this vehicle new in 2000 and had the entire unit undercoated for rust protection and sound proofing. The truck has been garaged since new and since I travel for business has low mileage. This is my personal vehicle not a work truck. As time went on I began noticing the rust under the chassis and then I received a recall notice for the spare tire bracket. I found… Read more

I purchased this vehicle new in 2000 and had the entire unit undercoated for rust protection and sound proofing. The truck has been garaged since new and since I travel for business has low mileage. This is my personal vehicle not a work truck. As time went on I began noticing the rust under the chassis and then I received a recall notice for the spare tire bracket. I found out later that Toyota used the spare tire recall to understand the magnitude of the chassis rust problem. A short time later I received the recall for the chassis exchange. When I picked up the truck there was something wrong with the steering, the wheel did not return to straight after a turn. I complained that night and was told it was normal. After a few hindered miles the linkage was worn and had to be replaced. My mechanic told me the cab was not aligned to the rack when they changed the chassis. My complaint is with the rot issue. The rear axle is now rotted to a point where it is leaking though the casing, not through a seal or fitting but through the rotted metal. I do not view a rear axle as a wear/replacement part unless it is abused through the working of the truck. I am 62 years old and have been driving sine 16 and have never ever had to replace a rear axle for rot. The fact that Toyota acknowledged ownership for the chassis rust tells me that they should own the axle rot as well. I have called Toyota corporate with no success and am looking for some relief on this repair. Toyota quoted me a

NHTSA complaint #10896244
Jan 19, 2015structure, service brakes
On 11//18/0/01irc'd a recall for excessive corrosion of the rear cross member. In 10/2012,I was informed that the truck frame passed inspection and was good.they did replace two gas tank straps and told me the undercoating that should be sprayed on it as part of the recall was not available.I never received any addition correspondence regarding the undercoating.on 12/23,14 I… Read more

On 11//18/0/01irc'd a recall for excessive corrosion of the rear cross member. In 10/2012,I was informed that the truck frame passed inspection and was good.they did replace two gas tank straps and told me the undercoating that should be sprayed on it as part of the recall was not available.I never received any addition correspondence regarding the undercoating.on 12/23,14 I took my truck to tj Toyota for a trailer light whip repair. At that time, the mechanic had me look at the frame rail.it is rusted so bad I could see right through the rail.the connection of this rail to the frame has excessive scaling.the truck was due for an inspection at the end of the month, and I was told they would not do an inspection.the mechanic continued to tell me he felt the truck was "junk" unsuitable for towing anything.I called 1-800-331-4331 at Toyota and spoke with [xxx], [xxx] and [xxx]. [xxx] processed a conference call with herself, [xxx] at tj Toyota and me. [xxx] told me to take the truck back to tj Toyota to redo the frame inspection and if it failed, Toyota would replace the frame. However, [xxx], from tj Toyota stated it is not corroded on the frame but it is on the rail connecting to the frame. I asked what they would for me and he stated, spray it with undercoating. I asked what that would do for the truck and [xxx] stated nothing?. Nnyroads are salted heavily.if this vehicle was never undercoated or protected for rust, the fact that the rails are rusted is due to not be

NHTSA complaint #10676510
Apr 7, 2014service brakes
Tl* the owns a 2001 Toyota Tundra. The contact stated that while driving downhill at approximately 30 MPH on a mountainous road, the brakes were depressed and pulsated abnormally as the front end of the vehicle began to vibrate violently. The failure only recurred when the contact was driving downhill in combination to the brake pedal being engaged. The vehicle was taken to an… Read more

Tl* the owns a 2001 Toyota Tundra. The contact stated that while driving downhill at approximately 30 MPH on a mountainous road, the brakes were depressed and pulsated abnormally as the front end of the vehicle began to vibrate violently. The failure only recurred when the contact was driving downhill in combination to the brake pedal being engaged. The vehicle was taken to an authorized dealer, who stated that the rotors and calipers would need to be replaced. The vehicle had not been repaired. The manufacturer was notified of the defect. The approximate failure mileage was 60,000.

NHTSA complaint #10578086
Jan 28, 2014structure, service brakes

My brakes line rusted off. I got it replaced. If I didn't notice it I could have gotten into a major accident with no brakes. My frame on the pickup is rusting and I am concerned that it will become another safety issue. I have owned toyotas all my life and now worried to drive them due to rusty frames. *tr

NHTSA complaint #10561790
Dec 13, 2012steering, structure, service brakes
The 1st generation Toyota Tundra's are rust buckets. I own a 2001 Toyota Tundra w/ approx 101,000 miles. The vehicle was taken to the local authorized dealer for repairs under recall: 09v444000 (structure: frame and members:underbody shields). The vehicle is being repaired (frame is being replaced). But the dealer also informed me that the steering rack and hose… Read more

The 1st generation Toyota Tundra's are rust buckets. I own a 2001 Toyota Tundra w/ approx 101,000 miles. The vehicle was taken to the local authorized dealer for repairs under recall: 09v444000 (structure: frame and members:underbody shields). The vehicle is being repaired (frame is being replaced). But the dealer also informed me that the steering rack and hose connections are rotted out and in need of replacement -> $1300. Additionally, the dealer informed me that the rear e-brake pivots are rusted/frozen and will also need replacing ->> $450. In a nutshell, the frame, the steering and the brakes are all rusted out - it appears that safety was an afterthought. I feel that Toyota corporation is negligent and that consumers are left holding the bag for poorly engineered products that are prone to early rust-out. On-line forums are filled with threads from other owners experiencing similar issues. *tr

NHTSA complaint #10488708
Nov 15, 2012service brakes
To whom it may concern: I am writing this letter in an effort to make Toyota motors corporation responsible for the defective braking system on Toyota tundras 2001 ,and probably other years,specifically the front brake calipers . From what the Toyota dealerships tell me these trucks came with front calipers that are too small for the vehicle and they get too hot and as a… Read more

To whom it may concern: I am writing this letter in an effort to make Toyota motors corporation responsible for the defective braking system on Toyota tundras 2001 ,and probably other years,specifically the front brake calipers . From what the Toyota dealerships tell me these trucks came with front calipers that are too small for the vehicle and they get too hot and as a result they warp the discs and this creates a moderate to violent shaking of the front end of the vehicle every time the brakes are applied . Toyota motors repaired the issue, by installing bigger calipers with more surface area, as long as the car was within the warranty 3 years or 36,000 miles . It is my opinion that this issue should be examined and be considered a government recall because it is not that a part broke or got worn out before the warranty expired . It is more that the car came with brakes not capable of withstanding the heat generated by the friction b/w the pads and the disc due to the design of the caliper and as a result it warps the discs causing owners to resurface or replace discs frequently without solving the problem or solving it for a short period of time and needless to say this ,to me, is a big safety issue not only because the brakes do not work properly but also because all that shaking and vibration can loosen up other components in the suspension or braking system compromising the safety of the vehicle and as a result this may cause an accident . Many disappointed Tundra

NHTSA complaint #10484742
May 9, 2012steering, suspension, service brakes, hydraulic, parking brake, structure
Due to premature corrosion (vehicle 4 years old) parking brake failed to function, failed nys inspection, was repaired (03/14/2005). Due to premature corrosion, spring broke, was repaired (01/02/2008). Power steering rack rotted, had to be replaced. Approx mileage 150,000. Front suspension links rotted out. Called Toyota (04/15/2009) voiced our concern for rotting frame, no… Read more

Due to premature corrosion (vehicle 4 years old) parking brake failed to function, failed nys inspection, was repaired (03/14/2005). Due to premature corrosion, spring broke, was repaired (01/02/2008). Power steering rack rotted, had to be replaced. Approx mileage 150,000. Front suspension links rotted out. Called Toyota (04/15/2009) voiced our concern for rotting frame, no recall at that time. They issued a complaint #.took vehicle to dealer for inspection for three recalls, a0f, b0d, 90m on 05/02/2012. Inspection not properly done, chunks of rust still can be flaked off, possible holes behind, but they sprayed crc over top of the loose scaling, covering over the problems. We had no choice in what they were doing with our property. We took it in for an inspection. After said inspection, if it would not get a new frame, we would have opted to take it home, removed all loose scaling prior to the crc being applied. We were not given any options, our vehicle was already on the way to their collision shop for the work. This would have accomplished two things; the dealership would know without a doubt that there were no holes and the crc would stick directly to the frame minimizing future corrosion (that is the objective of the recall afterall) I called Toyota corporate and voiced my concern with a spray covering over the problem, and the truck not being safe. My case is still pending, but based on the initial call back from the case manager, it is not looking like there will be a

NHTSA complaint #10457866
May 9, 2012suspension, service brakes, hydraulic
Due to premature corrosion (vehicle 4 years old) parking brake failed to function, failed nys inspection, was repaired (03/14/2005). Due to premature corrosion, spring broke, was repaired (01/02/2008). Power steering rack rotted, had to be replaced. Approx mileage 150,000. Front suspension links rotted out. Called Toyota (04/15/2009) voiced our concern for rotting frame,… Read more

Due to premature corrosion (vehicle 4 years old) parking brake failed to function, failed nys inspection, was repaired (03/14/2005). Due to premature corrosion, spring broke, was repaired (01/02/2008). Power steering rack rotted, had to be replaced. Approx mileage 150,000. Front suspension links rotted out. Called Toyota (04/15/2009) voiced our concern for rotting frame, no recall at that time. They issued a complaint #.took vehicle to dealer for inspection for three recalls, a0f, b0d, 90m on 05/02/2012. Inspection not properly done, chunks of rust still can be flaked off, possible holes behind, but they sprayed crc over top of the loose scaling, covering over the problems. We had no choice in what they were doing with our property. We took it in for an inspection. After said inspection, if it would not get a new frame, we would have opted to take it home, removed all loose scaling prior to the crc being applied. We were not given any options, our vehicle was already on the way to their collision shop for the work. This would have accomplished two things; the dealership would know without a doubt that there were no holes and the crc would stick directly to the frame minimizing future corrosion (that is the objective of the recall afterall) I called Toyota corporate and voiced my concern with a spray covering over the problem, and the truck not being safe. My case is still pending, but based on the initial call back from the case manager, it is not looking like t

NHTSA complaint #10457859
Nov 26, 2011service brakes, hydraulic
Brakes pulsate and go all the way to the floor; you must quickly release and re-apply to stop vehicle then you get a bad vibration and horrible noises before vehicle finally stops. My service mechanic cannot get Toyota to fax him the diagrams he needs to diagnose and repair issue. I have read over 300 complaints online about this same issue from other 2001 Toyota Tundra… Read more

Brakes pulsate and go all the way to the floor; you must quickly release and re-apply to stop vehicle then you get a bad vibration and horrible noises before vehicle finally stops. My service mechanic cannot get Toyota to fax him the diagrams he needs to diagnose and repair issue. I have read over 300 complaints online about this same issue from other 2001 Toyota Tundra owners. This is a safety issue and there have been near miss accidents because of this issue. *tr

NHTSA complaint #10437314
Nov 21, 2011service brakes, hydraulic
Tl* the contact own a 2001 Toyota Tundra. The contact stated that while driving approximately 45 MPH, the steering wheel began to vibrate vigorously. The vehicle was taken to an independent mechanic for diagnostic. The technician stated that the rotors would have to be replaced. The failure continued after the rotors were replaced. The mechanic then stated that the failure may… Read more

Tl* the contact own a 2001 Toyota Tundra. The contact stated that while driving approximately 45 MPH, the steering wheel began to vibrate vigorously. The vehicle was taken to an independent mechanic for diagnostic. The technician stated that the rotors would have to be replaced. The failure continued after the rotors were replaced. The mechanic then stated that the failure may be occurring because the vehicle's weight was too excessive for the braking system. The vehicle was not repaired. The approximate failure mileage was 18,000.

NHTSA complaint #10436646
Oct 30, 2011service brakes, hydraulic
2001 Toyota Tundra complaint: while I was driving in the city all of a sudden I lost 90% of my braking ability. After pulling over to the side and inspecting my front brakes I notice my left driver's side had fluid on the road and tire. Limping it home and on farther inspection the bracket that supports the flex line from the frame to bracket and the ridged line from the… Read more

2001 Toyota Tundra complaint: while I was driving in the city all of a sudden I lost 90% of my braking ability. After pulling over to the side and inspecting my front brakes I notice my left driver's side had fluid on the road and tire. Limping it home and on farther inspection the bracket that supports the flex line from the frame to bracket and the ridged line from the bracket to the brake caliper was rusted off, this caused the ridged line to fracture. After purchasing a new bracket I than needed to look at the passenger side to see exactly how to mount the new bracket, to my surprise the passenger side bracket was also rusted off. I am sure it would have been a short period of time before I loss my brakes again had I not inspected the passenger side. When notifying the dealer about it I was pretty much blown off as the only person with this problem there for I probably just imagined it. So I guess my complaint is recalling these trucks for an inspection of singular rust problem such as the spire tire bracket is a joke. These trucks are just simply road hazards and are going to get a lot of people killed if action is not taken to get these rust buckets off the road. *tr

NHTSA complaint #10433603
Jun 1, 2011service brakes, hydraulic
Tl*the contact owns a 2001 Toyota Tundra. The contact stated while driving 65 MPH, he applied the brakes and the vehicle would not slow down until the contact engaged the brakes aggressively before the vehicle came to a complete stop. The manufacturer was contacted and told him to contact the dealer. The dealer was not contacted. The vehicle was not repaired. The failure… Read more

Tl*the contact owns a 2001 Toyota Tundra. The contact stated while driving 65 MPH, he applied the brakes and the vehicle would not slow down until the contact engaged the brakes aggressively before the vehicle came to a complete stop. The manufacturer was contacted and told him to contact the dealer. The dealer was not contacted. The vehicle was not repaired. The failure mileage was unavailable the current mileage was 140,000.

NHTSA complaint #10404006
Mar 9, 2011service brakes, hydraulic

Im on the third set of front brakes for my truck which just turned 60000 miles and it is a 2001 Toyota Tundra. This is totally unacceptable for a vehicle of this mileage. *tr

NHTSA complaint #10389667
May 5, 2010service brakes, hydraulic
Tl*the contact owns a 2001 Toyota Tundra. The contact received a recall notice for recall 09v444000 (structure: frame and members:underbody shields). The contact also stated that the vehicle would vibrate rapidly when the brakes were applied and the check engine light would also illuminate. The contact called the dealer and the dealer offered no assistance. The VIN was… Read more

Tl*the contact owns a 2001 Toyota Tundra. The contact received a recall notice for recall 09v444000 (structure: frame and members:underbody shields). The contact also stated that the vehicle would vibrate rapidly when the brakes were applied and the check engine light would also illuminate. The contact called the dealer and the dealer offered no assistance. The VIN was unavailable. The failure mileage was 4. The current mileage was approximately 84,000.

NHTSA complaint #10328956
Mar 10, 2010suspension, parking brake, structure

We own a 2001 Tundra with severe rust problems on the frame, brakes, body parts, spare tire, suspension and nuts and bolts all over the vehicle. The spare tire dropped from the rear of the truck due to rust and damaged the rear bumper. We have spent thousands of dollars to repair rusted items on this truck. *tr

NHTSA complaint #10318593
Mar 4, 2010service brakes, hydraulicCrash
2001 Tundra brakes failed to stop truck from hitting vehicle in front on a sudden stop on the interstate. Found out later that Toyota knew of defective brakes and issued tsb br004-002 to replace 191mm front brake calipers with larger 231 mm calipers within the warranty period, but did not notify owners of the defect. Only owners who complained of vibration when braking and… Read more

2001 Tundra brakes failed to stop truck from hitting vehicle in front on a sudden stop on the interstate. Found out later that Toyota knew of defective brakes and issued tsb br004-002 to replace 191mm front brake calipers with larger 231 mm calipers within the warranty period, but did not notify owners of the defect. Only owners who complained of vibration when braking and early failure of front rotors and brake pads were offered the upgraded calipers, but only after repeated complaints. The upgraded calipers were eventually incorporated into the 2004 and later tundras. *tr

NHTSA complaint #10316747
Mar 4, 2010service brakes, hydraulic

My 2001 Tundra vibrated so bad when I went to slow down form highway speeds. The vibration is so bad the truck steering and dash shake I have replaced the rotors and drums I think the problem is the rear drums having to do with the bypass valve sending fluid back to the brake peddle or some thing because it only happens when the 2 drums lop so the auto bake adjust. *tr

NHTSA complaint #10316447
Mar 2, 2010service brakes, hydraulic, equipment
Toyota Tundra brake issue. My truck brakes start to pulse at all speed while attempting to stop. I have inside the last two years replaces three sets of front brake pads and rotors. This is particularly frightening while apply the brakes exiting the freeway on wet roads the brakes don't seem to want to stop the truck in a straight line and the front end has a tendency to jump… Read more

Toyota Tundra brake issue. My truck brakes start to pulse at all speed while attempting to stop. I have inside the last two years replaces three sets of front brake pads and rotors. This is particularly frightening while apply the brakes exiting the freeway on wet roads the brakes don't seem to want to stop the truck in a straight line and the front end has a tendency to jump and drift to one side of the road. I have made several attempts my self having the brakes repaired by qualified mechanic and even to blame the brakes on one mechanic that he did not know what he was doing I have since found that he did know what he was doing he just did knot know about the Toyota Tundra brake issue history as I did not know as well till now. Each time the mechanic blamed it on the driving habits. This is not the case, as the last time I had my brakes worked on was just last year in november and found that the brakes have done the same thing in less time then in the past. In addition the mechanic found that the pulsing of the front end had damaged the front end which cost over $3,000.00 to fix. Its just now after the Toyota gas peddle issue came to light that I started to do some research and found that this has been happening for over 8 years with the Toyota tundras all over the country. This is a real issue with the Tundra year 2001. *tr

NHTSA complaint #10315580
Feb 27, 2010parking brake

I have an 2001 Toyota Tundra that was purchased and has been driven in the northeast. It has a rusted(quoted from a Toyota mechanic) emergency brake line. Wondering if this is apart of the rust recall already in place with the tundras. *tr

NHTSA complaint #10314887
Nov 17, 2009service brakes, hydraulic, structureCrash1 injured

2001 Toyota Tundra brake failure resulting in single vehicle accident running off the road into ditch and had to be towed. Inspection photos available demonstrate brake line corrosion along with chassis and frame rust through. *tr updated 03/29/10 *bf pictures received 10/05/10.

NHTSA complaint #10292497
Nov 7, 2007service brakes, hydraulic, electrical systemFire
Tl*the contact owns a 2001 Toyota Tundra. While the vehicle was parked in the garage, the ABS electronic control module melted onto the floor. The garage was filled with grey smoke, ash, and soot. The mechanic stated that an electrical short occurred and the ABS electronic control module's power unit remains operational when the engine is shut off. The vehicle was towed to… Read more

Tl*the contact owns a 2001 Toyota Tundra. While the vehicle was parked in the garage, the ABS electronic control module melted onto the floor. The garage was filled with grey smoke, ash, and soot. The mechanic stated that an electrical short occurred and the ABS electronic control module's power unit remains operational when the engine is shut off. The vehicle was towed to a mechanic. The ABS control module will be replaced and the wiring harness may also need to be replaced. The washer fluid bottle tubes were damaged. The current and failure mileages were 82,300.

NHTSA complaint #10208376
Jan 25, 2006suspension, service brakes, hydraulicCrash3 injured

Brakes and ball joint failure of Toyota Tundra lim. 4door 4.7l 8 cylinder 4x4 right side wheel came off and hit two persons on the shoulder of the highway in which one was killed.*ak

NHTSA complaint #10148570
Dec 25, 2005service brakes, hydraulicFire

Antilock unit caught fire while the vehicle was parked at work. There was no previous indication of a problem. Severe damage to vehicle. Have pictures. *nm

NHTSA complaint #10146056
Aug 21, 2005service brakes, hydraulic, equipmentCrash
I bought my 2001 Toyota Tundra in febuary of 2005. When ide bought the brakes where in good shape. After just 3 months of driving my truck started shaking violently when applying the brakes at higher speeds (30-55mph). I took it to a mechanic and he said that the brakes were shot and that the rotors were in need of turning. I proceeded with the repairs and was back on the road… Read more

I bought my 2001 Toyota Tundra in febuary of 2005. When ide bought the brakes where in good shape. After just 3 months of driving my truck started shaking violently when applying the brakes at higher speeds (30-55mph). I took it to a mechanic and he said that the brakes were shot and that the rotors were in need of turning. I proceeded with the repairs and was back on the road again till two nights ago. My family and I were coming home after sunset when a cow darted out in the middle of the road. I acted quickly and veired only to find that the brakes didnt work causing me to loose control of my truck. I was able to regain control by knowing the proper procedures from a defensive driving course ide taken when my occupation was as a firefighter but I still came in contact with the animal in the road due to the brake failure. Ive since taken the truck back to my mechanic and the brakes and rotors are shot once again. He said the exceedingly rapid ware of the brakes and rotors came from a malfunction on the rear brakes which in turn causes over strain on the front brakes resulting in premature break failure. Ive searched the internet and if your staff can possibly do the same they'll find that this has been a terribly common problem in the Toyota tundras year model 2000 through 2004. Ive recently started circulating a petition for others that have had these problems with their Toyota to accumulate proof that the problem has exsisted for some time now and that it has happened

NHTSA complaint #10133648
Oct 9, 2003service brakes, airCrash
My 2001 Tundra vibrates and pulsates when braking. I have had brake pads installed and the rotors turned 3 time in the last four months. But the problem is still there. Because of this problem I have been in an accident. Thank god I wasn't injured. I have heard and read about other Tundra owners having the same problem. When will they make Toyota recall the Tundra's… Read more

My 2001 Tundra vibrates and pulsates when braking. I have had brake pads installed and the rotors turned 3 time in the last four months. But the problem is still there. Because of this problem I have been in an accident. Thank god I wasn't injured. I have heard and read about other Tundra owners having the same problem. When will they make Toyota recall the Tundra's because of the bad braking system on them? When several people loss their lives. I just it will be the ford incident all over again. *la

NHTSA complaint #10041500
← All 2001 Toyota Tundra problems & recalls