Jan 19, 2024exterior lighting
Headlight shows visible signs of over heating of the amber lenses on both driver and passenger side. Amber lenses are melted, obscured, burned through and causing additional discoloration to the clear lens of the headlight itself. This creates a safety issue for both driver and passenger side headlights and amber lights not illuminating properly but also reducing the… Read more
Headlight shows visible signs of over heating of the amber lenses on both driver and passenger side. Amber lenses are melted, obscured, burned through and causing additional discoloration to the clear lens of the headlight itself. This creates a safety issue for both driver and passenger side headlights and amber lights not illuminating properly but also reducing the reliability and longevity of the lighting systems themselves.
NHTSA complaint #11566610
Jun 2, 2021exterior lighting
The daytime driving lights are too hot causing the plastic housing to melt, crack and, in some cases, break. My research has found that this is a common problem in Toyota Tacoma trucks from 2005-11. In april 2015, Toyota replaced the headlight assemblies with a supposed "redesigned" assembly to address this issue. However, now in april 2021, the "redesigned" assemblies have… Read more
The daytime driving lights are too hot causing the plastic housing to melt, crack and, in some cases, break. My research has found that this is a common problem in Toyota Tacoma trucks from 2005-11. In april 2015, Toyota replaced the headlight assemblies with a supposed "redesigned" assembly to address this issue. However, now in april 2021, the "redesigned" assemblies have again melted, cracked and broken due to the daytime driving lights being too hot and too close to the light assembly. Nothing was redesigned in 2015. Whatever safety or fire hazard in the owner or operator that caused Toyota to replace the headlight assemblies in 2015 still exists today. I have contacted Toyota and my dealer and they have offered no assistance or remedy.
NHTSA complaint #11419375
Jan 21, 2021exterior lighting
There is an issue on driving amber signal lights located on front of vehicle. Bulbs are too hot, and have melted and cracked the lense cover on the inside of the head light assembly. It is hampering light out put, and could form a hole in the future which will provide a high beam of light to on coming traffic. Also, it could ignite due to heat and plastic melting. Reports… Read more
There is an issue on driving amber signal lights located on front of vehicle. Bulbs are too hot, and have melted and cracked the lense cover on the inside of the head light assembly. It is hampering light out put, and could form a hole in the future which will provide a high beam of light to on coming traffic. Also, it could ignite due to heat and plastic melting. Reports of this occuring on Toyota vehicles have been numerous with no resolve. Mind you, this is a engineer or manufacturing mishap and error as they failed to consider at the moment of designing /manufacturing, and now the results are more than evident. Other Toyota vehicles are not having this issue which means that someone figured out a resolve on their future production in order to avoid bad publicity. It is fair to say, that Toyota should replace such a defect, or reimburse its customers who decide to replace them due to such a defect. Thank you for considering the validity of this manner!
NHTSA complaint #11389155
Feb 3, 2020exterior lighting
Running lights are melting the head light clear assembly...this is the second time for the running light bulbs to melt the head light assembly..the heat is 233 degrees using a digital heat reader...the yellow bulbs are 24 watts..
NHTSA complaint #11306835
Aug 30, 2019exterior lighting
Burnt headlight len. The running light lens is burnt and cracked due to overheating. When I tried to contact Toyota's recall phone number, after over a dozen attempts, the number was always busy.
NHTSA complaint #11252528
Mar 17, 2019electrical system, exterior lighting
Headlight lens get hot melted lens, light bulb plug is also burned ready to crack this is a safety issue
NHTSA complaint #11187394
Mar 4, 2019exterior lightingFire
Front headlights have yellow signal and daytime running lights that are always on and the light bulb heat up causing the plastic to heat and melt and still feel hot when using on a long drive. I worry about my car catching on fire
NHTSA complaint #11183962
Aug 28, 2018exterior lighting
2009 Toyota Tacoma. Consumer writes in regards to bubble and crack in passenger front turn signal. *ld the consumer stated the dealer refused to repair the vehicle due to the expiration date for the repair to be made ended in 2015.*js
NHTSA complaint #11122568
Jan 4, 2018exterior lighting
The running lights melt the plastic headlamp covers and literally melt the plastic, this is a picture of my second set that are also melting
NHTSA complaint #11058589
Sep 20, 2017exterior lighting
Headlamps drl bulbs burned through lens. Toyota will not cover even though this was recalled previously. The design of these headlights is flawed!
NHTSA complaint #11024696
Jun 4, 2017exterior lighting
Day time running lights melted headlights
NHTSA complaint #10993102
Feb 15, 2016exterior lighting
Parking light assembly built into headlight assembly have broken and looks like they are ready to catch fire. Split in to causing lens to blacken
NHTSA complaint #10826160
Feb 5, 2016exterior lighting
Daytime running lights have burned and cracked lenses. Toyota corporate says the recall is over. This needs to be fixed--repair costs over $500. Please help--
NHTSA complaint #10824547
Jan 30, 2016exterior lighting
Both headlamp assemblies inner lens distorted/bubbling, and one side is cracked with the inner lens separated
NHTSA complaint #10823195
Mar 20, 2014exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the lenses for the daytime running lamps and the turn signals were melted. The contact was concerned that the failure could lead to a fire. The dealer was contacted and advised that the entire lighting assembly would require replacing. The manufacturer was made aware of the failure but provided no assistance.… Read more
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the lenses for the daytime running lamps and the turn signals were melted. The contact was concerned that the failure could lead to a fire. The dealer was contacted and advised that the entire lighting assembly would require replacing. The manufacturer was made aware of the failure but provided no assistance. The vehicle was not repaired. The failure mileage was 40,000. The current mileage was 100,000.
NHTSA complaint #10573863
Mar 20, 2014exterior lightingFire
Tl * the contact owns a 2009 Toyota Tacoma. The contact stated that the headlight lens would continuously overheat and become cracked. The contact was concerned that the vehicle would possibly catch on fire since the bulb was so close to the lens. The vehicle was not taken for inspection or repairs. The manufacturer was not made aware of the failure. The failure mileage was… Read more
Tl * the contact owns a 2009 Toyota Tacoma. The contact stated that the headlight lens would continuously overheat and become cracked. The contact was concerned that the vehicle would possibly catch on fire since the bulb was so close to the lens. The vehicle was not taken for inspection or repairs. The manufacturer was not made aware of the failure. The failure mileage was 50,000 and the current mileage was 100,000. Updated 3/13/14*cn
NHTSA complaint #10573851
Oct 31, 2013exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the head light bulbs were overheating and causing the lens to melt. The vehicle was taken to the dealer where the technician verified the failure and stated that the headlight assembly needed to be replaced. The manufacturer was made aware of the failure. The vehicle was not repaired. The failure mileage was unknown and the current mileage was 77,000.
NHTSA complaint #10550387
Oct 23, 2013exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the plastic fog light cover was fractured and became melted. The vehicle was taken to the dealer for diagnosis where the technician stated that the fog light cover would have to be replaced. The manufacturer was made aware of the failure. The vehicle was not repaired. The approximate failure mileage was 56,000.
NHTSA complaint #10549202
Jul 2, 2013electrical system, exterior lightingFire
The plastic housing/plastic lens covering the amber daytime running lights and the clear fog lights are burned, melted, cracked and broken. This is not due to any front end collision but due to the extreme heat generated by the original factory-installed light bulbs. The lights are generating so much heat that they are melting, burning and cracking the plastic housing which… Read more
The plastic housing/plastic lens covering the amber daytime running lights and the clear fog lights are burned, melted, cracked and broken. This is not due to any front end collision but due to the extreme heat generated by the original factory-installed light bulbs. The lights are generating so much heat that they are melting, burning and cracking the plastic housing which then breaks under driving stress. Compounding the problem is that there is no way to turn off the daytime running lights when the vehicle is in operation. Either the daytime running lights must be on or the headlights must be on. Therefore, the lights continue to burn the plastic housing. Toyota will not completely cover the cost to repair and replace these defective light systems stating that the vehicle is out of the 3 year warranty. Although the vehicle is one year out of the 3 years manufacturer's warranty this problem did not occur overnight but is the result of 4 years of use. The lens have been progressively getting worse over time. Because the lens are burned, we are concerned that a fire could occur. *tr
NHTSA complaint #10522926
Apr 2, 2013exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the dtr lights malfunctioned and melted the headlight case. The vehicle was taken to the dealer where they advised him that the dtr light bulb assembly needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and offered no assistance. The failure mileage was approximately 50,000. The… Read more
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the dtr lights malfunctioned and melted the headlight case. The vehicle was taken to the dealer where they advised him that the dtr light bulb assembly needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and offered no assistance. The failure mileage was approximately 50,000. The current mileage was approximately 89,569. *tr
NHTSA complaint #10505409
Dec 3, 2012exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the daytime running lights were melting the headlight lenses. The vehicle was taken to a dealer for diagnosis and the contact was informed that the lenses would need to be replaced. The manufacturer was notified and offered to pay for the cost of the lens but not for the labor costs. The vehicle was not… Read more
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the daytime running lights were melting the headlight lenses. The vehicle was taken to a dealer for diagnosis and the contact was informed that the lenses would need to be replaced. The manufacturer was notified and offered to pay for the cost of the lens but not for the labor costs. The vehicle was not repaired. The failure and current mileage was 51,000.
NHTSA complaint #10487209
Nov 2, 2012exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the daytime running lights would cause the headlight lens to overheat, melting the plastic lenses. The vehicle was taken to the dealer who advised that there was a bulletin from the manufacturer that stated if any headlight was defective they have to replace both headlights. The dealer will repair the failure… Read more
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the daytime running lights would cause the headlight lens to overheat, melting the plastic lenses. The vehicle was taken to the dealer who advised that there was a bulletin from the manufacturer that stated if any headlight was defective they have to replace both headlights. The dealer will repair the failure of the parts free of charge, but the contact has to pay for the labor. The manufacturer was notified and advised the contact that there were no recalls and offered no further assistance. The vehicle was not repaired. The VIN was unknown. The failure mileage was 37,800.
NHTSA complaint #10483144
Oct 24, 2012exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that the headlight lenses became melted and cracked. The vehicle was taken to a dealer for inspection but they only took pictures of the failure. The vehicle was not repaired. The manufacturer was notified who stated that the vehicle was out of warranty. The failure mileage was 37,383.
NHTSA complaint #10482088
Oct 11, 2012exterior lightingFire
After completing an oil change on my 2009 Toyota Tacoma in october of 2011 I noticed that the amber lens in the headlight was discolored and seemed to be melting due to overheating. Over the past year I have been monitoring the situation and noticed that the melting and cracking of the amber lens inside of the headlight is progressively getting worse. It seems that the daytime… Read more
After completing an oil change on my 2009 Toyota Tacoma in october of 2011 I noticed that the amber lens in the headlight was discolored and seemed to be melting due to overheating. Over the past year I have been monitoring the situation and noticed that the melting and cracking of the amber lens inside of the headlight is progressively getting worse. It seems that the daytime running lights were not properly engineered in this model. Because of the defect there is a clear concern for driver safety. The melting lenses create an obvious fire hazard. The Toyota dealership where I purchased my Tacoma in the metro atlanta area advised me that Toyota has no recall of extended warranty for this "known" problem. I was very dismayed to hear this because the issue is clearly presents a threat to the driver. Because of this situation I have to make a decision on what options are available to me. Either I replace the entire headlight assembly with the Toyota factory assembly which is already known to have a defect or purchase and aftermarket headlight assembly and hope the it is engineered better than the Toyota one, or I figure out a way to disable the daytime running lights to cut back on the head that builds up with them constantly being on. I would rather not disable the daytime running lights because I believe that they do provide significant safety value. I am not sure what I am going to do at this point but clearly action is needed. I would like Toyota to step up to the plate and
NHTSA complaint #10479782
Aug 30, 2012exterior lightingFire
The running / parking lights are burning through and melting the lens covers on both sides of headlight assemblies. There are visible burn marks and cracks on the lens for both sides of the vehicle. *tr
NHTSA complaint #10473096
Apr 26, 2012exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. While examining the vehicle, the contact noticed that the daytime running lights were beginning to melt the headlight housing. The vehicle was not diagnosed or repaired. The VIN was not available. The current and the failure mileage was 60,000.
NHTSA complaint #10456591
Nov 14, 2011exterior lightingFire
Tl* the contact owns a 2009 Toyota Tacoma. The contact stated that front turn signal lenses burned out. The contact noticed visible burn marks on both lenses. The vehicle was not taken to the dealer for inspection or repairs. The manufacturer was made aware of the failure. The vehicle was not repaired. The failure mileage was 60,000 and the current mileage was 66,000.
NHTSA complaint #10435526
Oct 25, 2011exterior lightingFire
Daylight running lights burn /melt the lens due to excessive heat, in less then 30k miles. I believe Toyota has a design problem with the drls. Every Tacoma with the drl option will eventually have this problem. The compartment that holds the dlr light is small, with no ventilation, and the lamp dissipates approximately 28 watts of heat, which is focused toward the lens… Read more
Daylight running lights burn /melt the lens due to excessive heat, in less then 30k miles. I believe Toyota has a design problem with the drls. Every Tacoma with the drl option will eventually have this problem. The compartment that holds the dlr light is small, with no ventilation, and the lamp dissipates approximately 28 watts of heat, which is focused toward the lens (along with the light). It is simply too much heat in too small an area, and the heat is sufficient to melt the plastic lens in front of the lamp. Since the drl is part of the headlight assembly, the cost of parts is reported to be around $700 plus labor. I believe that lenses (with proper lamps) should never melt. Asking Tacoma owners to pay $700 +, every 30k miles is outrageous! My headlight assemblies were replaced under warranty, but they are sure to fail again if something is not done to correct the design of the dlrs. It appears that Toyota is ignoring the problem and hoping most people won't recognize the problem until after the vehicle is out of warranty. Now I am concerned that this condition will eventually lead to an electrical fire. *tt
NHTSA complaint #10432814
Sep 8, 2011exterior lightingFire
My 09 Toyota Tacoma drl (daylight running light/turn signal) lens burned/melted/broke. I have exceeded my warranty but I feel Toyota should stand behind their product and replace my light lens. My local dealer did do a 50/50 split on the cost of replacement, but this is a design problem. Light lens should never burn/melt/break regardless of how old or how many miles the… Read more
My 09 Toyota Tacoma drl (daylight running light/turn signal) lens burned/melted/broke. I have exceeded my warranty but I feel Toyota should stand behind their product and replace my light lens. My local dealer did do a 50/50 split on the cost of replacement, but this is a design problem. Light lens should never burn/melt/break regardless of how old or how many miles the vehicle has on it. Not all Tacoma's have drl , this is an option, my local dealer did not know this but I pointed this out to him. I have a friend with same problem but his Tacoma is still in warranty and the dealer did a 100% replacement. I contacted Toyota with a letter and pictures and was told Toyota would not stand behind their product because I had exceeded my warranty. *tr
NHTSA complaint #10424219