CarProblemsDB

2016 Ram 2500 transmission problems

65 owners reported transmission & powertrain problems — 25% of all 262 complaints about the 2016 Ram 2500.

Transmission & powertrain complaints by Ram 2500 year

20262
20258
20247
20237
202250
202125
202020
201931
201875
201742
201665
201544
201462
201322
201235
201116

What owners report

Nov 12, 2026power train

The contact owns a 2016 Ram 2500. While the contact's son was starting the vehicle, the gear shifter detached. The dealer was contacted and made aware of the failure. The contact was informed of an unknown recall with a similar failure; however, the VIN was not associated with a recall for the failure.

NHTSA complaint #11777542
Aug 31, 2026power train, electrical system
I am reporting a transmission safety problem with my 2016 Ram 2500 cummins that began shortly after fca campaign u29 was performed. Before the recall work, the transmission and original solenoid were functioning normally. I had no transmission symptoms, warning lights, or transmission codes. The dealership performed u29 and replaced the transmission solenoid may 4-6, 2026. I… Read more

I am reporting a transmission safety problem with my 2016 Ram 2500 cummins that began shortly after fca campaign u29 was performed. Before the recall work, the transmission and original solenoid were functioning normally. I had no transmission symptoms, warning lights, or transmission codes. The dealership performed u29 and replaced the transmission solenoid may 4-6, 2026. I picked the truck up may 6 at 149,091 miles. About 79 miles later, the check-engine light came on and transmission problems began. While driving, including on the interstate, the truck would suddenly jerk, the rpms would rise quickly, and the truck would lose speed. On several occasions, traffic behind me had to react quickly to avoid hitting me. The dealership told me the solenoid installed during the u29 repair was defective and replaced it with another solenoid. The same problems continued. The truck later developed code p0871, became undriveable, and was towed back june 1. The original transmission ultimately failed. The dealership then installed a mopar remanufactured transmission. I picked it up june 13. Within roughly 600 miles, it developed substantially identical symptoms and failure patterns, including p0870 and p0871, limp mode, and another major transmission failure. It was towed back june 24. The dealership later found the overdrive clutch had disintegrated and metal was present in the transmission fluid. The failed remanufactured transmission is now being handled under its mopar warranty

NHTSA complaint #11760982
Aug 25, 2026power trainCrash
On august 25, 2026, my 2016 Ram 2500 was parked on private property. The driver states that she placed the automatic transmission in park before exiting the vehicle. After she exited, the unoccupied vehicle unexpectedly began rolling and struck a tree, causing vehicle damage. No one was injured. There were no known warning lights or messages indicating a problem before the… Read more

On august 25, 2026, my 2016 Ram 2500 was parked on private property. The driver states that she placed the automatic transmission in park before exiting the vehicle. After she exited, the unoccupied vehicle unexpectedly began rolling and struck a tree, causing vehicle damage. No one was injured. There were no known warning lights or messages indicating a problem before the incident. The cause has not yet been determined and the vehicle has not yet been inspected for this incident. The vehicle is available for inspection. This vehicle is equipped with a steering-column-mounted automatic transmission shifter. I am concerned that the incident may involve the transmission/shift interlock/park system. I am aware of NHTSA recall 17v-821 (fca t79), involving unintended rollaway in certain Ram trucks, as well as NHTSA recall query rq25003 concerning reported btsi failures in vehicles including Ram 2500 models. The NHTSA VIN lookup currently shows zero unrepaired recalls for this vehicle; however, I do not yet know whether the prior t79 recall repair was performed on this specific vehicle or when it was performed. I did call the dealership and they said possibly 0ctober 3, 2018. I am submitting this complaint because the vehicle rolled after the driver reports placing the transmission in park and exiting the vehicle.

NHTSA complaint #11759520
Apr 22, 2026power train, engine

Grid heater nut/bolt detached and entered engine, causing catastrophic internal failure and total engine loss while driving.

NHTSA complaint #11733046
Feb 14, 2026power train, unknown or other

Got into my truck after letting it warm up and the shifter broke out of the handle. It’s a known problem cause the design is flawed by putting so much pressure on the part. So in the end it breaks and then you can’t get your vehicle out of park or whatever gear it broke in. I was charged 718.00 for it to get fixed when I think this should be a recall or tsb.

NHTSA complaint #11718053
Nov 10, 2025power train
Incident report – gear shift failure date of incident: 11/10/2025 vehicle: 2016 Ram 2500 pickup truck VIN [xxx] mileage: [insert mileage] location: [insert location of incident] description of incident while attempting to shift the vehicle from park (p) into drive (d), the shift lever suddenly went limp and lost all resistance. Upon applying slight additional pressure to… Read more

Incident report – gear shift failure date of incident: 11/10/2025 vehicle: 2016 Ram 2500 pickup truck VIN [xxx] mileage: [insert mileage] location: [insert location of incident] description of incident while attempting to shift the vehicle from park (p) into drive (d), the shift lever suddenly went limp and lost all resistance. Upon applying slight additional pressure to engage the transmission, the shift lever snapped off completely. The gear shift bracket—the component securing the shift rod—fractured in half at the point where the shift rod inserts into the bracket. This mechanical failure rendered the vehicle inoperable and unable to be shifted out of park. No warning lights or prior symptoms were observed before the failure. The broken part was visually inspected and confirmed to be the shifting lever bracket, consistent with mopar part number 68470756aa. Immediate actions taken the vehicle was safely secured to prevent unintended movement. Engine was turned off and keys removed. Visual inspection confirmed that the shift lever bracket had broken at the rod insertion point. Tow service was arranged for transport to a repair facility. Photographs of the damaged bracket and shifter assembly were taken for documentation. Assessment this incident represents a critical component failure of the gear shift mechanism, resulting in sudden loss of control over transmission operation. The break occurred under normal shifting force, indicating a possible material or des

NHTSA complaint #11698580
Oct 13, 2025power train

I previously had recall 17v-821 work completed. This recall was for the brake transmission shift interlock (btsi) locking pin may become stuck in the open position. I have the same issue now and see that NHTSA is investigating failed recall fixes. I have taken this to the dealer and an independent shop and am now trying to figure out how to get this repaired.

NHTSA complaint #11693040
Sep 29, 2025power train
The contact owns a 2016 Ram 1500. The contact stated that the shift solenoid change message was displayed. The vehicle was taken to the local dealer for a recall repair. Upon retrieving the vehicle, the vehicle failed to shift and had no power. The vehicle was diagnosed with a faulty shift solenoid. The replacement parts were on backorder. The local dealer later informed the… Read more

The contact owns a 2016 Ram 1500. The contact stated that the shift solenoid change message was displayed. The vehicle was taken to the local dealer for a recall repair. Upon retrieving the vehicle, the vehicle failed to shift and had no power. The vehicle was diagnosed with a faulty shift solenoid. The replacement parts were on backorder. The local dealer later informed the contact that the transmission was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and filed a complaint. The manufacturer declined to cover the cost of the repair. The failure mileage was approximately 238,000.

NHTSA complaint #11690345
Jul 14, 2025power train

Transmission gear selector lever can be moved from park to reverse, neutral, and drive without having the brake pedal depressed. This is the way the transmission gear selector currently operates. This is not a one-time incident. I bought this vehicle recently and noticed this transmission gear selector lever issue about a month ago.

NHTSA complaint #11673363
May 28, 2025power train, engine

It is the water pump we have the concentric brand with out a vent hole picture attached ( which is the one under recall but doesn’t come up on our VIN) yes a mechanic no no

NHTSA complaint #11663422
Sep 7, 2024power train
I have a 2016 Ram 2500 power wagon that I have turned into a show truck. The truck has never been off-road or in the mud, it is driven to and from the shows. Last [xxx] as I was driving to hickory, nc for a car show on saturday august 31st my truck instantly lost power and turned on the engine light. The transmission felt like it was stuck in second or third gear, so I pulled… Read more

I have a 2016 Ram 2500 power wagon that I have turned into a show truck. The truck has never been off-road or in the mud, it is driven to and from the shows. Last [xxx] as I was driving to hickory, nc for a car show on saturday august 31st my truck instantly lost power and turned on the engine light. The transmission felt like it was stuck in second or third gear, so I pulled over and scanned the PCM to see what the dtc code and it came back as p0870. Went online to research the code and see what it had to say about it and it stated to clear the code to see if it comes back on which I didn't. The light has not returned as of yet but when the truck hits overdrive it has a high pitch squeal coming from it meaning the transmission. I brought it in to my local dealership on wednesday september 4th to have it looked at they performed diag and cvi inspection to find the transmission is starting to fail internally recommend replacing the transmission. Now want me to pay out of pocket for a new transmission even though I have max care warranty on the truck when I bought it new. I don't have $6000.00 to pay for a new transmission that's on back order. If it comes down to it and I have to get my neighbor to help me get the transmission out of this truck cause I'm [xxx] then I will rebuild it my [xxx] thing myself before I pay them $6000.00. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)

NHTSA complaint #11613233
Feb 28, 2023power trainCrash
The contact owns a 2016 Ram 2500. The contact stated that the vehicle was previously repaired under NHTSA campaign number: 17v821000 (power train). The contact stated that while the vehicle was turned off with the key out of the ignition, the vehicle rolled backward and crashed into some trees. Additionally, the contact was able to move the gear shifter while the vehicle was… Read more

The contact owns a 2016 Ram 2500. The contact stated that the vehicle was previously repaired under NHTSA campaign number: 17v821000 (power train). The contact stated that while the vehicle was turned off with the key out of the ignition, the vehicle rolled backward and crashed into some trees. Additionally, the contact was able to move the gear shifter while the vehicle was turned off. The contact's son was inside the vehicle when the failure occurred; however, no injuries were sustained. No police report was filed. The vehicle was taken to the dealer, and the contact was informed that the recall repair failed prevent the failure. The manufacturer was made aware of the failure. The failure mileage was approximately 30,000.

NHTSA complaint #11509458
Jul 15, 2022power train
Previous fca campaign #u30 of solonoid pack for transmission 68rfe has been completed in 2018 and in june of 2022 a transmission service technician stated the one from the recall was faulty and needed replaced. Upon replacement with oem solonoid pack the truck went into limp mode and was locked into 4th gear. Vehicle is undrivable and at the dealer. After further inspection… Read more

Previous fca campaign #u30 of solonoid pack for transmission 68rfe has been completed in 2018 and in june of 2022 a transmission service technician stated the one from the recall was faulty and needed replaced. Upon replacement with oem solonoid pack the truck went into limp mode and was locked into 4th gear. Vehicle is undrivable and at the dealer. After further inspection the solonoid issue caused the clutch pack to shed debris into the bottom on the transmission pan which just had a new gasket, filters and fluid less than 20 miles ago. Transmission tech stated the debris was no there and saw no evidence of failure to the clutch pack prior to the replacement of the solonoid. Now transmission has to be rebuilt at owned expense. Vehicle has 72,000 miles and is not used for towing or aggressive driving.

NHTSA complaint #11474197
May 25, 2022power train, engine
I was driving my truck on the freeway pulling a loaded stock trailer. The truck suddenly down shifted into fourth gear and the engine rpm’s maxed out! I almost crashed the truck because the momentum of the trailer pushed the truck sideways on the freeway. I had to avoid traffic and get to the shoulder. Truck would not shift out of fourth gear and truck shifted into 4wd low… Read more

I was driving my truck on the freeway pulling a loaded stock trailer. The truck suddenly down shifted into fourth gear and the engine rpm’s maxed out! I almost crashed the truck because the momentum of the trailer pushed the truck sideways on the freeway. I had to avoid traffic and get to the shoulder. Truck would not shift out of fourth gear and truck shifted into 4wd low also on its own. Had truck towed to dealers ship and was told a shift solenoid went out. Because of that they now have to change the torque converter and replace the transmission from the damaged it caused. It is unknown if it damaged any of the engine components at this time or any other parts of the drivetrain. Now I’m stuck paying for a transmission because dodge didn’t put a safety backup into their system to prevent this in case of a failure. I see that I am not the first person it’s happened to by reading the power train comments for this year truck.

NHTSA complaint #11466065
Mar 14, 2022power trainCrash1 injured
The contact owns a 2016 Ram 2500. The contact stated while the vehicle was parked and running, she opened the front driver's side door and stepped on the running board with her body between the front driver's side door and the vehicle frame. The vehicle lunged forward independently, turned to the left and crashed into the front end of the passenger's side of the unoccupied… Read more

The contact owns a 2016 Ram 2500. The contact stated while the vehicle was parked and running, she opened the front driver's side door and stepped on the running board with her body between the front driver's side door and the vehicle frame. The vehicle lunged forward independently, turned to the left and crashed into the front end of the passenger's side of the unoccupied vehicle parked next to it. The contact became trapped between the two vehicles and pinned between the driver's side door and the frame of her vehicle. The contact stated that the vehicle was squeezing continuously as if it had shifted into drive. The contact attempted to honk the horn by extending the keys on her left arm but was unsuccessful and started screaming for help. Two individuals arrived at the scene but could not unlock the door and were unable to break the front passenger's side window to unlock the door in order to extract the contact. The contact squeezed her body and reached out the unlock button on the driver's side door, and she unlocked the door. One of the individual got inside the vehicle, shifted into reverse and reversed slowly in order to release and extract the contact. The vehicle was parked. The contact was then extracted but was knocked unconscious. The contact was airlifted to the hospital where she was informed that she had sustained six broken ribs, damaged clavicle required surgery, damaged lungs due to squeezing, squeezed organs to one side of her abdomen, bruises on both gl

NHTSA complaint #11456603
Jan 25, 2022power train

My truck will shift in to gear without the key being in or the truck being on. I found a recall (t79) listed but my VIN does not seem to be listed under this recall.

NHTSA complaint #11448915
Oct 26, 2021power trainFire

My transmission got so hot climing up a hill it caught the excused on fire, thankfully had water in the truck an put the fire out no warnings nothing, just flush transmission hot went to stop an realized it was on fire, had to have transmission rebuilt an cooler lines an cooler repaired, still not runing right.

NHTSA complaint #11438257
Sep 30, 2021power train
The contact owns a 2016 Ram 2500. The contact stated that while driving 65 MPH, the rpm gauge revved to the red line; the contact released the accelerator pedal and the vehicle jerked, then the transmission shifted inadvertently to fourth gear and would not allow the contact to shift gear to drive. The vehicle was hauling a trailer at the time of the failure. The vehicle was… Read more

The contact owns a 2016 Ram 2500. The contact stated that while driving 65 MPH, the rpm gauge revved to the red line; the contact released the accelerator pedal and the vehicle jerked, then the transmission shifted inadvertently to fourth gear and would not allow the contact to shift gear to drive. The vehicle was hauling a trailer at the time of the failure. The vehicle was taken to the dealer and diagnosed with the torque converter control being out of range. The vehicle was not repaired and remained at the dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 80,000.

NHTSA complaint #11435044
Feb 14, 2021power train

When moving from reverse to drive the transmission stays in 1st gear only allowing up to 35 to 45 MPH and does not shift to next gear.

NHTSA complaint #11396143
Nov 26, 2020power train

Able to shift into drive without pressing the brake. Put the truck back in park to see if it was just the one time but it continued to be able to shift out of park without pressing the brake. We have not had this occur previously or we have just always been pressing the brake.

NHTSA complaint #11376457
Oct 23, 2020power train
The check engine light keeps coming on. I have had at the dealership 3 times. The third time the dealer had my vehicle for 6 weeks. When I went and picked it up, I got approximately 1 mile down the road and the check engine light came on again. I took the vehicle back to the dealer and it is currently still being worked on to try and figure the problem out. The check engine… Read more

The check engine light keeps coming on. I have had at the dealership 3 times. The third time the dealer had my vehicle for 6 weeks. When I went and picked it up, I got approximately 1 mile down the road and the check engine light came on again. I took the vehicle back to the dealer and it is currently still being worked on to try and figure the problem out. The check engine code keeps showing the torque converter. The dealer changed the valve body the third time that it was there.

NHTSA complaint #11366007
Jul 4, 2020power train, electrical system, engine

I purchased my vehicle yesterday. Today I was driving it is stalled as I was pulling out into traffic I restarted it it drove fine another two miles. At which time is stalled again with no lights, no indications on. Sounds like some noise comes from the air box. Some kind of air noise comes from the passenger side of the engine when it happened

NHTSA complaint #11337451
Jun 24, 2020engine and engine cooling, power train, equipment
Tl* the contact owns a 2016 Ram 2500. The contact received notification of NHTSA campaign number: 19v818000 (equipment, engine and engine cooling) and 20v036000 (power train) however the parts to do the repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The contact stated that the vehicle was taken… Read more

Tl* the contact owns a 2016 Ram 2500. The contact received notification of NHTSA campaign number: 19v818000 (equipment, engine and engine cooling) and 20v036000 (power train) however the parts to do the repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The contact stated that the vehicle was taken three times to landmark dodge chrysler jeep Ram, 6850 mt zion blvd, morrow, ga 30260, and was rejected to be serviced due to the parts not being available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available for NHTSA campaign number: 19v818000 (equipment, engine and engine cooling), and part distribution disconnected for NHTSA campaign number: 20v036000 (power train).

NHTSA complaint #11330461
Apr 27, 2020power train
Tl* the contact owns a 2016 Ram 2500. The contact stated while shifting the gears to park, the vehicle automatically reversed. The contact was able to resume the vehicle back to normal after a few days. The contact stated no warning light was illuminated. The vehicle was taken to local dealer napleton ellwood city chrysler dodge jeep Ram located at 1000 lawrence ave, ellwood… Read more

Tl* the contact owns a 2016 Ram 2500. The contact stated while shifting the gears to park, the vehicle automatically reversed. The contact was able to resume the vehicle back to normal after a few days. The contact stated no warning light was illuminated. The vehicle was taken to local dealer napleton ellwood city chrysler dodge jeep Ram located at 1000 lawrence ave, ellwood city, pa 16117 where it was diagnosed that the main wiring harness needed to be replaced. The vehicle had not been repaired as of yet. The manufacturer was notified of the failure and referred the contact to NHTSA. The failure mileage was approximately 12,000.

NHTSA complaint #11322391
Mar 9, 2020power train, engine
Tl* the contact owns a 2016 Ram 2500. The contact received notification of NHTSA campaign number: 19v818000 (equipment, engine and engine cooling) and 20v036000 (power train) however, the parts to do the recall repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called bergey's chrysler… Read more

Tl* the contact owns a 2016 Ram 2500. The contact received notification of NHTSA campaign number: 19v818000 (equipment, engine and engine cooling) and 20v036000 (power train) however, the parts to do the recall repairs were not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called bergey's chrysler jeep dodge Ram located at (408 harleysville pike, souderton, pa 18964 (215) 721-3470) but was not diagnosed or repaired. The contact did not experience a failure. The manufacturer was contacted however no further assistance was provided. VIN tool confirms parts not available.

NHTSA complaint #11316993
Jan 3, 2020power train

Clutch master cylinder failed while driving in 2nd gear, no clutch pressure, could not stop truck and it would not stall, I ended up turning key off after driving over curb on to sidewalk. This was while trying to stop for stopped cars at traffic light. Fortunately I was only moving at maybe 10 MPH. Florida truck, 26k miles on it.

NHTSA complaint #11296970
Dec 26, 2019power train
Tl* the contact owns a 2016 Ram 2500. While traveling various speeds, the 4 wheel drive lever would shift independently and the "4 wheel drive shift in progress" warning message would illuminate. The contact took the vehicle to several dodge dealers, including athens dodge chrysler jeep Ram (4145 atlanta hwy, athens, ga 30606), gwinnett chrysler dodge jeep Ram (5054 ga-78,… Read more

Tl* the contact owns a 2016 Ram 2500. While traveling various speeds, the 4 wheel drive lever would shift independently and the "4 wheel drive shift in progress" warning message would illuminate. The contact took the vehicle to several dodge dealers, including athens dodge chrysler jeep Ram (4145 atlanta hwy, athens, ga 30606), gwinnett chrysler dodge jeep Ram (5054 ga-78, stone mountain, ga 30087), and akins dodge chrysler jeep Ram (220 w may st, winder, ga 30680). The actuator and electrical harness were replaced; however, the failure continued. The manufacturer informed the contact to take the vehicle back to the original dealer to be serviced. The contact brought the vehicle back to athens dodge, but they were unable to duplicate the failure. The vehicle had not been repaired. The failure mileage was less than 10,000.

NHTSA complaint #11291272
Oct 28, 2019power train
While driving with or without my travel trailer at different speeds a loud grounding noise is heard from under or toward the front dive train and has some feedback felt from the steering wheel sometimes the service 4wd lights up but not always I must slow down to a crawl ingage the 4wd stop back up cut off ignition restart sometimes it disengages 4wd and sometimes when I slow… Read more

While driving with or without my travel trailer at different speeds a loud grounding noise is heard from under or toward the front dive train and has some feedback felt from the steering wheel sometimes the service 4wd lights up but not always I must slow down to a crawl ingage the 4wd stop back up cut off ignition restart sometimes it disengages 4wd and sometimes when I slow to a crawl a mechanical clunk can be heard and truck works normally . Durning the time the grinding sound is present the 4wd will not function and the 4wd indicater light will not come on. When this fisrt occurred the truck had around 4000 miles it was taken to the dealer conway chystler conway sc 29528 they replaced transfer case control module said it was fixed I picked it up it did it again about 5 miles from dealership I took it back they again replaced a part the axle locker actuator said it was fixed 7 days total in shop now for third time at 12000 miles its doing it again back to conway I have contacted fca to ask for a buyback this is very unsafe if this truck ingages 4wd pulling my camper on the interstate it could cause a crash so I now will no longer drive this truck unless I absolutly have to if no buyback is issued I will request a libility letter be issued to me from fca releasing me from any libility of this truck being sold or traded

NHTSA complaint #11271602
Oct 1, 2019power trainCrash1 injured
Tl* the contact owns a 2016 Ram 2500. While attempting to shift gears, the gear shifter separated from the steering column. The vehicle was taken to bryant motors (2901 south limit ave, sedalia, mo) where the failure was repaired. Later, while backing out of the garage, the transmission would not switch into the drive position. The vehicle would only drive in fourth gear and… Read more

Tl* the contact owns a 2016 Ram 2500. While attempting to shift gears, the gear shifter separated from the steering column. The vehicle was taken to bryant motors (2901 south limit ave, sedalia, mo) where the failure was repaired. Later, while backing out of the garage, the transmission would not switch into the drive position. The vehicle would only drive in fourth gear and was taken back to the dealer who replaced the brake transmission shift interlock solenoid. On one occasion, after switching into the park position with the engine still running, the driver exited the vehicle. Moments later, the vehicle erroneously drove backwards and knocked the driver to the ground. The vehicle also struck two additional individuals who were positioned behind the vehicle. The vehicle then crashed into two parked vehicles and a motorcycle. The driver sustained neck and back injuries that required medical attention. A police report was not filed. The vehicle was towed. The cause the failure was not determined. The manufacturer was notified of the failures. The dealer was not contacted about the crash. The failure mileage was 36,000.*dt

NHTSA complaint #11265322
Sep 25, 2019power train
Tl* the contact owns a 2016 Ram 2500. After starting the vehicle, the contact heard an abnormal clicking noise emerging from the engine. There were no warning indicators illuminated. The vehicle was towed to plaza chrysler dodge jeep Ram (2077 hwy 44 w, inverness, fl 34453, (352) 726-1238) where it was diagnosed that the tension pulley fractured and snapped. The failure… Read more

Tl* the contact owns a 2016 Ram 2500. After starting the vehicle, the contact heard an abnormal clicking noise emerging from the engine. There were no warning indicators illuminated. The vehicle was towed to plaza chrysler dodge jeep Ram (2077 hwy 44 w, inverness, fl 34453, (352) 726-1238) where it was diagnosed that the tension pulley fractured and snapped. The failure damaged the serpentine belt, water pump, and wiring harness. The manufacturer and dealer were not contacted. The failure mileage was 24,000. The VIN was not available.

NHTSA complaint #11257954
Sep 12, 2019power train, service brakes
Tl* the contact owns a 2016 Ram 2500. While attempting to drive up a hill with a trailer in tow, the vehicle failed to accelerate. The contact also stated that the rear brakes failed to appropriately stop the vehicle. The contact took the vehicle to corwin chrysler dodge jeep Ram fiat (located at 1025 w sunshine st, springfield, mo 65807, 417-862-9272) where the dealer stated… Read more

Tl* the contact owns a 2016 Ram 2500. While attempting to drive up a hill with a trailer in tow, the vehicle failed to accelerate. The contact also stated that the rear brakes failed to appropriately stop the vehicle. The contact took the vehicle to corwin chrysler dodge jeep Ram fiat (located at 1025 w sunshine st, springfield, mo 65807, 417-862-9272) where the dealer stated the issue was related to the hill assist system. The vehicle was not diagnosed or repaired. The manufacturer was contacted and opened a case; however, the contact had not heard back from the manufacturer. The approximate failure mileage was 103,311.

NHTSA complaint #11255139
Jul 23, 2019power train
Tl* the contact owns a 2016 Ram 2500. While driving 55 MPH, the gear shifted into first gear on its own and the check engine warning indicator illuminated. The contact veered to the shoulder of the road, and turned off and restarted the vehicle. The vehicle was driven to an independent mechanic who diagnosed that the transmission needed to be replaced. Hall chrysler dodge jeep… Read more

Tl* the contact owns a 2016 Ram 2500. While driving 55 MPH, the gear shifted into first gear on its own and the check engine warning indicator illuminated. The contact veered to the shoulder of the road, and turned off and restarted the vehicle. The vehicle was driven to an independent mechanic who diagnosed that the transmission needed to be replaced. Hall chrysler dodge jeep Ram virginia beach (3152 virginia beach blvd, virginia beach, va 23452, (877) 475-0721) was contacted to schedule a second diagnostic test. The dealer informed the contact that the parts were not available to perform the repair. The vehicle was not repaired and the failure recurred. The manufacturer was not made aware of the failure. The failure mileage was approximately 62,000.

NHTSA complaint #11234112
Jun 20, 2019power trainCrash
Tl* the contact's husband owns a 2016 Ram 2500. While the vehicle was parked in a driveway, it shifted out of park and rolled in reverse up a small hill, crashed into a house, and the vehicle came to a stop only because the driver side door was open which stopped the vehicle from reversing any further. The contact mentioned that the driver was unloading at the time and did not… Read more

Tl* the contact's husband owns a 2016 Ram 2500. While the vehicle was parked in a driveway, it shifted out of park and rolled in reverse up a small hill, crashed into a house, and the vehicle came to a stop only because the driver side door was open which stopped the vehicle from reversing any further. The contact mentioned that the driver was unloading at the time and did not sustain any injuries due to the failure. The vehicle was not taken to a dealer or an independent mechanic for the failure. Testing. The vehicle was not repaired. The vehicle was previously repaired per NHTSA campaign number: 17v821000 (power tran) at dayton andrews dodge chrysler jeep Ram dealer, (located at 2301 24th st n, st petersburg, fl 33713, (727) 321-0500). The manufacturer was not notified of the failure. The approximate failure mileage was 31,000.

NHTSA complaint #11221567
Jun 13, 2019steering, power train
Drag link has been recalled on my pickup. Was given what was supposed to be a temporary fix by the dealership that involved welding the nuts to the adjuster sleeve. Now there is a permanent fix and I was told by chrysler and the dealership that the weld is good enough. I am unable to have my vehicle aligned due to this weld. I will be unable to have any future work that… Read more

Drag link has been recalled on my pickup. Was given what was supposed to be a temporary fix by the dealership that involved welding the nuts to the adjuster sleeve. Now there is a permanent fix and I was told by chrysler and the dealership that the weld is good enough. I am unable to have my vehicle aligned due to this weld. I will be unable to have any future work that involves the steering done due to this weld. If the weld fails, I'll be left once again with a bad drag link. How is this acceptable? The nits has to be tightened three times before they were welded!

NHTSA complaint #11219881
Oct 26, 2018power train
Tl* the contact owns a 2016 Ram 2500. While the vehicle was stationary, the transmission failed to operate properly. Upon placing the vehicle in park, the gear shift slipped out of gear on several occasions over the past five months. On one occasion, the vehicle slipped into reverse and independently accelerated backwards rapidly. The contact stated that the vehicle was placed… Read more

Tl* the contact owns a 2016 Ram 2500. While the vehicle was stationary, the transmission failed to operate properly. Upon placing the vehicle in park, the gear shift slipped out of gear on several occasions over the past five months. On one occasion, the vehicle slipped into reverse and independently accelerated backwards rapidly. The contact stated that the vehicle was placed in park, but the gear shift indicator erroneously displayed another gear. Classic chrysler dodge jeep Ram (1102 walton drive, texarkana, texas 75503, (903) 716-0600) was made aware of the failures, but could not duplicate them or locate the source. The manufacturer was not made aware of the failures. The failure mileage was approximately 30,000.

NHTSA complaint #11142945
Sep 18, 2018power train

When driving between 62and 80mph the truck develops a shack through the whole truck that make it hard to see out of mirrors and is uncomfortable to drive not feeling very safe

NHTSA complaint #11130258
Sep 16, 2018power train
Driving 73 MPH and loud 'explosion' and violent shake came from center of truck. Close to lithia dodge in bryan tx. Pulled in to see transmission fluid pouring from transmission. Truck has been in the shop for two weeks. Service advisor indicated that u joint failed and cracked the transmission. Requiring the replacement of transmission and drive shaft. Dangerous situation.… Read more

Driving 73 MPH and loud 'explosion' and violent shake came from center of truck. Close to lithia dodge in bryan tx. Pulled in to see transmission fluid pouring from transmission. Truck has been in the shop for two weeks. Service advisor indicated that u joint failed and cracked the transmission. Requiring the replacement of transmission and drive shaft. Dangerous situation. Chrystler should be held accountable. Very concerned that truck could have be sent violently across the road.

NHTSA complaint #11129779
Sep 5, 2018power train

For the last year or so, I have been having an issue with the 4wd shift in progress message coming on at random times. I have had it to the dealership where I purchased it at, victory Ram of kansas city and they "could not duplicate the problem".

NHTSA complaint #11124563
Sep 5, 2018power train, engine
Tl* the contact owns a 2016 Ram 2500. The contact received notifications for NHTSA campaign numbers: 17v821000 (power train) and 17v562000 (engine and engine cooling). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. Cedar city chrysler dodge jeep Ram (1010 n main st, cedar city, ut 84721, (435) 586-8290) was contacted and… Read more

Tl* the contact owns a 2016 Ram 2500. The contact received notifications for NHTSA campaign numbers: 17v821000 (power train) and 17v562000 (engine and engine cooling). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. Cedar city chrysler dodge jeep Ram (1010 n main st, cedar city, ut 84721, (435) 586-8290) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was notified and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA complaint #11124529
Aug 20, 2018power train, electrical system, structure, latches/locks/linkages, vehicle speed control
Tl* the contact owns a 2016 Ram 2500. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v486000 (structure, latches/locks/linkages). The contact called glendenning motor company at 641-464-3241 (located at 1100 e south st, mt ayr, ia 50854) and was informed that the parts were not availaable. The manufacturer was made aware of the issue… Read more

Tl* the contact owns a 2016 Ram 2500. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v486000 (structure, latches/locks/linkages). The contact called glendenning motor company at 641-464-3241 (located at 1100 e south st, mt ayr, ia 50854) and was informed that the parts were not availaable. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact stated that he received notification of NHTSA campaign number: 18v332000 (electrical system, vehicle speed control). The vehicle was taken to the same dealer and the cruise control was reprogrammed. While driving at any speed, the cruise control accelerated or decelerated randomly. The vehicle was taken back to the dealer and the cruise control was reprogrammed again. The failure recurred and the dealer stated that nothing else could be done. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure mileage was approximately 11,100. Parts distribution disconnect for 17v821000 (power train) and VIN tool confirms parts not available for 18v486000 (structure, latches/locks/linkages).

NHTSA complaint #11121084
← All 2016 Ram 2500 problems & recalls