May 3, 2024wheels, service brakes
The contact owns a 2002 Mercedes-Benz ml320. The contact stated while driving at approximately 25 MPH, the driver’s side front wheel independently braked. The contact stated he had not depressed the brake pedal but heard an abnormal sound from the tire screeching as the wheel had stopped rolling. The contact stated that the esp traction warning light was illuminated. The… Read more
The contact owns a 2002 Mercedes-Benz ml320. The contact stated while driving at approximately 25 MPH, the driver’s side front wheel independently braked. The contact stated he had not depressed the brake pedal but heard an abnormal sound from the tire screeching as the wheel had stopped rolling. The contact stated that the esp traction warning light was illuminated. The contact pulled the vehicle over, turned off, restarted the vehicle, and was able to continue driving. The contact stated that the failure occurred several minutes later. The contact stated that the failure occurred one other time and had not happened again. The contact had not taken the vehicle to a local dealer or independent. The vehicle had not been diagnosed and was not repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 198,000.
NHTSA complaint #11586737
Apr 30, 2022service brakes, forward collision avoidance
The car brakes suddenly by itself just after the esb/ABS lights come on along with an exclamation point (!). This has happened randomly at least 4 times since we purchased the car. Once at high speeds on the highway. It appears this problem is common with other owners of mercedes 2001-2002 ml's. According to the forums below, the problem seems to be a "yaw rate sensor"… Read more
The car brakes suddenly by itself just after the esb/ABS lights come on along with an exclamation point (!). This has happened randomly at least 4 times since we purchased the car. Once at high speeds on the highway. It appears this problem is common with other owners of mercedes 2001-2002 ml's. According to the forums below, the problem seems to be a "yaw rate sensor" malfunction or defect. My mercedes mechanic saw no error codes for this component and it seem extremely expensive (forum states part is $3000) to replace. The https://mbworld.org/forums/m-class-w163/233486-big-problems-ml320-pls-help-2.html
NHTSA complaint #11462862
Dec 10, 2021service brakes
There is a serious defect in the yaw rate sensors in these mercedes ml w163's. Thank god I was driving down a secluded road and nobody was behind me, but my vehicles brakes locked up, on their own, even with my foot on the accelerator pedal, with no warning lights or warning signals. I have no error codes, and my vehicle is well maintained. There are many many people that… Read more
There is a serious defect in the yaw rate sensors in these mercedes ml w163's. Thank god I was driving down a secluded road and nobody was behind me, but my vehicles brakes locked up, on their own, even with my foot on the accelerator pedal, with no warning lights or warning signals. I have no error codes, and my vehicle is well maintained. There are many many people that are having the same issue with their mercedes ml's. Some people have experienced this happening to them at freeway speeds. The yaw rate sensors are at fault, and send a signal to the ABS pump which in turn locks up the brakes without even touching the brake pedal! This is extremely dangerous to everyone in the vehicle, and to any other vehicle in the area. People can die! Again.. This is a terrible defective function of a sensor that will spontaneously apply the brakes fully to lock up automatically with no persuasion from the driver. It is extremely dangerous and can cause fatal injuries. This has been researched thru many mercedes forums including benzworld.org, mbworld.org, mercedesforum.com, and ml w163 facebook forum, all of which many ml owners have experienced the braking system lockup, and in some cases accidents have occurred. Another unfortunate issue in this happening, is that the brake lights do not light up when this sudden braking happens due to the yaw rate sensor malfunction. If there is a vehicle behind a mercedes ml when this sudden braking occurs, there is no warning lights, and can caus
NHTSA complaint #11443393
Jan 11, 2020electrical system, wheels, service brakes
Fuse box some has power some not. Front left wheel making this noise and stops after 25 miles per hour radio volume low when ignition key is on position 3 when key it's in the position 2 laud volume when key is not in I can turn on the stereo
NHTSA complaint #11298583
Dec 31, 2017electrical system, electronic stability control (esc), service brakes
I was driving on a busy intersection in my 2002 mercedes benz ml320 when driving the yellow triangle in the speedometer starts to flash and all the breaks lock up, this is followed by a stall, thankfully I was able to pull off to the side of the road without being hit. After doing some research I discovered that many mercedes ml320 owners were having this same problem.… Read more
I was driving on a busy intersection in my 2002 mercedes benz ml320 when driving the yellow triangle in the speedometer starts to flash and all the breaks lock up, this is followed by a stall, thankfully I was able to pull off to the side of the road without being hit. After doing some research I discovered that many mercedes ml320 owners were having this same problem. Specifically the yaw rate sensor. This is a serious life threatening issue that can injure or worse yet kill someone. You guys need to do a recall before someone dies!
NHTSA complaint #11057753
Nov 3, 2016electronic stability control (esc), service brakes
On numerous occasions occurring in different conditions regarding speed, weather, road conditions, etc., I have had the vehicle pull hard to the right while engaging the front brakes, both while turning the vehicle and on straightaways. When this occurs, the triangle hazard light and esp lights start flashing. Most often I have been able to pull off to the side of the road,… Read more
On numerous occasions occurring in different conditions regarding speed, weather, road conditions, etc., I have had the vehicle pull hard to the right while engaging the front brakes, both while turning the vehicle and on straightaways. When this occurs, the triangle hazard light and esp lights start flashing. Most often I have been able to pull off to the side of the road, thankfully safely, or on one occasion stop in the middle of the road as the car wouldn't allow me to continue driving which was incredibly dangerous and scary. I have taken it to the dealership who replaced the front brake sensors, which didn't fix the problem, and returned to have them again diagnose the issue and declined their recommendations such as replacing the back brake sensors, until I came upon the repeated issues of the stability sensors failing (specifically the yaw sensor). I can't believe that, to date, this has not been a recall issue and no one has been seriously injured or killed due to this problem (I filed a previous claim, but the website went under maintenance and closed my complaint as I was filing and was given id #10923983, but there is no information filed in association that I could find hence the re-filing). *tr
NHTSA complaint #10923995
Nov 3, 2016electronic stability control (esc), service brakes
On multiple occasions and numerous different speeds, weather, both driving on a straightaway or turning, and other road conditions, the front brakes have locked up on the car causing it to veer right while engaging the brakes. Most often I have had to pull over, thankfully safely, or on one occasion, stop in the middle of the road to turn the car off to be able to continue… Read more
On multiple occasions and numerous different speeds, weather, both driving on a straightaway or turning, and other road conditions, the front brakes have locked up on the car causing it to veer right while engaging the brakes. Most often I have had to pull over, thankfully safely, or on one occasion, stop in the middle of the road to turn the car off to be able to continue driving which is incredibly dangerous and scary. I've taken it to the dealership and they had me replace the brake sensors which were obviously not the problem and then recommended other replacements, since the problem continued, that I declined until I found that this was a common problem with the stability sensors in this vehicle (specifically the yaw sensor). I'm amazed this is not a recall situation and that no one has been seriously injured or killed due to this problem. *tr
NHTSA complaint #10923983
Aug 9, 2016vehicle speed control, service brakes
Tl* the contact owns a 2002 mercedes benz ml320. The contact stated that while driving at 60 MPH, the brakes independently engaged and caused the vehicle to veer to the side of the road. The contact mentioned that the ABS warning light illuminated and then the entire instrument panel illuminated. The vehicle was restarted but the failure recurred intermittently. The vehicle… Read more
Tl* the contact owns a 2002 mercedes benz ml320. The contact stated that while driving at 60 MPH, the brakes independently engaged and caused the vehicle to veer to the side of the road. The contact mentioned that the ABS warning light illuminated and then the entire instrument panel illuminated. The vehicle was restarted but the failure recurred intermittently. The vehicle was taken to an independent mechanic where it was diagnosed that the brake lamp switch failed. The vehicle was not repaired. The contact mentioned that the VIN was included in NHTSA campaign number: 11v208000 (vehicle speed control). The manufacturer was not notified of the failure. The failure mileage was 144,000.
NHTSA complaint #10894297
Jul 25, 2016service brakes
Brakes applied on their own without pedal pressure while car was moving at highway speed. Front brakes were smoking by the time I found a safe place to stop off the 4-lane road on a side road. Rear brakes seemed hot, but not smoking. No warning lights came on. Immediately before this highway event, car had just been traveling around 35 MPH on hilly side roads with steep… Read more
Brakes applied on their own without pedal pressure while car was moving at highway speed. Front brakes were smoking by the time I found a safe place to stop off the 4-lane road on a side road. Rear brakes seemed hot, but not smoking. No warning lights came on. Immediately before this highway event, car had just been traveling around 35 MPH on hilly side roads with steep ascents and descents. This is the fourth time brakes have self-applied in a similar manner. After second event, dealer examined car but could not reproduce the problem or find any faults on computer diagnostics. When brakes cool, car restarts without brakes coming on. Brake pads and sensors were replaced 6,000 miles earlier; significant brake drag was present for around two hundred miles after that repair; dealer said brakes were self-adjusting and declined to examine car at that time. It was about 4,000 miles after brake pad/sensor replacement that the self-braking problem started.
NHTSA complaint #10888170
Mar 1, 2016electrical system, service brakes
Tl* the contact owns a 2002 Mercedes-Benz ml320. While driving 10 MPH, the vehicle felt as if it slammed on the brakes without the contact depressing the brake pedal. The contact stated that the ebs and ABS warning lights remained illuminated. The contact also stated that the vehicle made a loud screeching sound when being driven. The vehicle was taken to a local mechanic… Read more
Tl* the contact owns a 2002 Mercedes-Benz ml320. While driving 10 MPH, the vehicle felt as if it slammed on the brakes without the contact depressing the brake pedal. The contact stated that the ebs and ABS warning lights remained illuminated. The contact also stated that the vehicle made a loud screeching sound when being driven. The vehicle was taken to a local mechanic where it could not be diagnosed. The manufacturer was made aware of the failure. The failure mileage was approximately 175,000.
NHTSA complaint #10839233
Jun 2, 2015electronic stability control (esc), service brakes
Tl* the contact owns a 2002 mercedes benz ml320. While driving approximately 45 MPH, the front brakes activated independently. The contact noticed that the front rotors were red and hot. The esp warning light illuminated. The contact disconnected the esp cable and continued to drive the vehicle. The manufacturer was not notified of the failures. The vehicle was not diagnosed… Read more
Tl* the contact owns a 2002 mercedes benz ml320. While driving approximately 45 MPH, the front brakes activated independently. The contact noticed that the front rotors were red and hot. The esp warning light illuminated. The contact disconnected the esp cable and continued to drive the vehicle. The manufacturer was not notified of the failures. The vehicle was not diagnosed or repaired. The VIN was unavailable. The approximate failure mileage was 139,000. Updated 7/21/15*cn updated 10/18/2017*cn
NHTSA complaint #10723025
May 5, 2015service brakes
Tl* the contact owns a 2002 mercedes benz ml320. The contact stated that while driving at various speeds, the brakes would erroneously activate and abruptly stop the vehicle. The contact indicated that when the failure occurs the bas/esp sensor light would illuminate. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 210,000.
NHTSA complaint #10714724
Feb 10, 2015service brakes
Tl*the contact owns a 2002 mercedes benz ml320. The contact stated that while driving at an unknown speed, all of the warning lights illuminated. The vehicle was taken to an independent mechanic where the technician diagnosed that the ABS system failed. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 67,000.
NHTSA complaint #10682608
Sep 8, 2014service brakes
While driving 40 MPH my ABS light shown up and all 4 tires lock up. Almost cause an accident. *tr
NHTSA complaint #10631672
May 13, 2014steering, electronic stability control (esc), service brakes
While driving on the highway at 60mph the vehicle started shaking violently. The brakes started engaging on their own pulling the car to the left and right and nearly bringing the car to a sudden stop. It took a lot of effort to keep the vehicle from pulling into the other lanes and causing an accident. The bas/esp light came on the dash and has stayed on now. This all lasted… Read more
While driving on the highway at 60mph the vehicle started shaking violently. The brakes started engaging on their own pulling the car to the left and right and nearly bringing the car to a sudden stop. It took a lot of effort to keep the vehicle from pulling into the other lanes and causing an accident. The bas/esp light came on the dash and has stayed on now. This all lasted for about 10 seconds. I was in the 3rd lane of a 4 lane highway during moderate traffic. I was almost rear ended by two different vehicles. I have been researching this issue and found many other drivers with the same thing. This is a dangerous defect and needs to be addressed. It doesn't take much for a sudden change in direction and speed to cause a severe accident when driving on the highway, and knowing that this vehicle is capable and know for doing this makes it very dangerous. It makes me wonder how many fatal accidents have occurred due to this problem, but no one knew because it was just assumed the to be driver error. *tr
NHTSA complaint #10587996
Mar 10, 2013service brakes
The anti-lock braking system would engage without driver activation. The bas/esp light would come on without any reason either. One day I was on the freeway when it happened and suddenly the breaks were engaged at 73 MPH when I was on the fast lane and other vehicles following at about the same speed. My leg was on the accelerator gassing to continue, but the anti-lock braking… Read more
The anti-lock braking system would engage without driver activation. The bas/esp light would come on without any reason either. One day I was on the freeway when it happened and suddenly the breaks were engaged at 73 MPH when I was on the fast lane and other vehicles following at about the same speed. My leg was on the accelerator gassing to continue, but the anti-lock braking system forced the car to almost a stop - about 10mph, before the breaks disengaged and the car continued to move (that is accelerate again). I almost got rammed by the vehicle behind me. I took it to mecerdes benz dealership in george town tx. They said it was unequal size tires that was the problem. I changed the tires to all new and the same size tries and the problem persisted. I took it back to the georgetown dealership again. This time their diagnosis was that the lateral acceleration and yaw sensors were faulty and needed to be replaced for $1250.00. What I described above was just an episode. It happen first when my wife was driving the car. It has happened several other times before I finally took it for repairs. I have packed the car for now because I have other cars to use and the problem has not still been fixed. NHTSA should issue a recall. *tr
NHTSA complaint #10502267
Nov 8, 2012steering, electronic stability control (esc), service brakes
Front passenger side wheel brake on it's own, pulling me off to the left of the road vehicle brake (right side) stayed engaged until vehicle speed was down to about 20 MPH. Dealer said a bad yaw rate sensor was the problem. *tr
NHTSA complaint #10483756
Apr 3, 2012service brakes, hydraulic
I recently took my 2002 ml320 into my local mercedes repair shop (fairfield, ct) to have some work done. When I collected the vehicle and as I was leaving, the esp/bas, ets and ABS lights came on simultaneously. This had happened on many previous occasions over the years and every time I had mentioned it to the mercedes service people they have said that this is a common… Read more
I recently took my 2002 ml320 into my local mercedes repair shop (fairfield, ct) to have some work done. When I collected the vehicle and as I was leaving, the esp/bas, ets and ABS lights came on simultaneously. This had happened on many previous occasions over the years and every time I had mentioned it to the mercedes service people they have said that this is a common fault and that I should turn off the engine, wait and then re-start and this should clear the issue. This had mostly worked until this recent occasion. Instead it the lights remained on and so I immediately drove the car back into the repair shop. The repair shop kept the vehicle for several days trying to isolate the cause. Eventually they found some serious corrosion in the esp/hydraulic control unit. They told me that this was related to an accident the car was involved in and suggested I contact my insurer. The insurance assessor examined the car in detail and concluded that the fault was entirely unrelated and their diagnosis was that the design of the unit was flawed. In other words this is a design fault. They said that given that this unit controls the entire braking system, any failure could be catastrophic. I had no choice but to authorize the repair. However, I am very concerned about this issue. The unit has been replaced at a cost of nearly $2,400 but if as the geico insurance assessor believes, this is a design fault then this is going to happen again. Additionally, it seems that
NHTSA complaint #10453913
Jun 14, 2011service brakes, hydraulic
Tl* the contact owns a 2002 mercedes benz ml55. While driving 65 MPH, the contact stated that the brake stability control activated without warning, causing the vehicle to idle abruptly. The vehicle was taken to a private mechanic who performed a diagnostic test which concluded that the yaw rate censor failed and needed to be replaced. The dealer informed the contact that… Read more
Tl* the contact owns a 2002 mercedes benz ml55. While driving 65 MPH, the contact stated that the brake stability control activated without warning, causing the vehicle to idle abruptly. The vehicle was taken to a private mechanic who performed a diagnostic test which concluded that the yaw rate censor failed and needed to be replaced. The dealer informed the contact that there were no related recalls. The manufacturer was not aware of the failure. No repairs were performed. The current and failure mileages were 70,000. The VIN was unavailable.
NHTSA complaint #10406842
Dec 1, 2010service brakes, hydraulic
2002 mercedes benz ml 500. Consumer writes regarding vehicle brake failure *tgw the consumer stated the brakes failed on the vehicle due to the brake lines leaking. *jb
NHTSA complaint #10368826
Jun 17, 2010service brakes, hydraulic
2002 ml 320 front brakes locked up by themselves nearly causing an accident. Burning smell detected from front wheels. Vehicle taken to dealer who claimed sensors had failed and that this was a rare problem; consumer charged to replace sensors. Less than one month later the same thing occurred, dealer now states it is a pressure issue but wants to keep vehicle overnight to… Read more
2002 ml 320 front brakes locked up by themselves nearly causing an accident. Burning smell detected from front wheels. Vehicle taken to dealer who claimed sensors had failed and that this was a rare problem; consumer charged to replace sensors. Less than one month later the same thing occurred, dealer now states it is a pressure issue but wants to keep vehicle overnight to duplicate stated problem. Owner initially noticed this problem over 1 year ago, taking it to the dealer thinking the emergency brake was sticking, causing the burning smell and sluggishness. During that visit the dealer stated it found no problem with the emergency brake. Owner paid to have rotors and brake pads replaced due to pitting and groving caused by the front brakes self-engaging; this did not fix the problem and the dealer is currently investigating a pressure issue. Vehicle has less than 24k miles on it and was purchased from the dealer brand new. *tr
NHTSA complaint #10336836
May 16, 2010service brakes, hydraulic, vehicle speed control
[mercedes benz ml 320 2002] while driving east on route 80 at 65 MPH and approaching the toll booths of the george washington bridge, I tapped my brakes to disengage my speed control. The speed control did not shut down. I hit the brake pedal several more times harder and harder, but the speed control stayed in control. I pushed down very hard on the brake pedal with both… Read more
[mercedes benz ml 320 2002] while driving east on route 80 at 65 MPH and approaching the toll booths of the george washington bridge, I tapped my brakes to disengage my speed control. The speed control did not shut down. I hit the brake pedal several more times harder and harder, but the speed control stayed in control. I pushed down very hard on the brake pedal with both feet and although the car slowed a little, the speed control dramatically speeded up the engine with the tachometer going almost full scale. I was able to reduce the car's speed from about 65 to under 50 MPH, but was still pretty scared. This was a terrifying experience and as an engineer I realized my options and time to react were very limited! I figured my choices were few: 1) brake until the car either stopped or I had hit the stopped cars at the toll booths (maybe damage the transmission further), 2) shift the car into neutral hoping that either the speed control would disengage or at least I could stop the car (engine rpms might run away and destroy the engine), or 3) try to shut off the speed control with the control stalk on the left of the steering column (which I obviously could not read closely to figure out where the stop might be). Fortunately, with several tries I was able to find the stop position on the speed control stalk and disengage the control. I braked very hard to stop short of a collision..... And got harsh words and looks from the adjacent toll collectors. I suspected t
NHTSA complaint #10330616
Oct 1, 2009service brakes, hydraulic, exterior lighting, equipment
I purchased a used 2002 ml320. Once the vehicle came of the lot it was fine in the beginning; however, the bas/esp continues to come on every two to three months. This prevents me from moving the gear shift from park to drive also the brake lights are not working (on or off when pressing on the brake pad)and when it does come on when I am driving at night other drivers cannot… Read more
I purchased a used 2002 ml320. Once the vehicle came of the lot it was fine in the beginning; however, the bas/esp continues to come on every two to three months. This prevents me from moving the gear shift from park to drive also the brake lights are not working (on or off when pressing on the brake pad)and when it does come on when I am driving at night other drivers cannot see any brake lights at all which puts my family and I in a safety situation or safety hazard which has occurred many times while driving. At first, I took it to napa on metro parkway in fort myers which they replaced the brake light switch and then two months to three months later the vehicle was taken back for the same situation. They replaced the switch and said the brake light switch they received was from mercedes benz. In the spring 2007 the same situation occurred and took it to mercedes benz of fort myers and they also replaced the switch as well. However, mercedes of fort myers changed and followed orders from corporate on what to do but to no avail. This has been an ongoing issue since the purchased of the ml320. Currently, october 1, 2009 the vehicle is at mercedes at fort myers for the same issue. My wife and I have contacted mercedes customer complaint with this issue but we feel enough is not being done to resolve. The situation began in the month of december 9, 2006 and continues presently which I have indicated. Other drivers came close to crashing into me due to no brakes lights. My
NHTSA complaint #10286007
Jan 11, 2009service brakes, hydraulic, fuel system, gasoline
Found identical problem per NHTSA action # ea08009 defect investigation. Constant loss of brake pressure. Warning lights indicated low brake fluid. Found fluid under car and in front left wheel-well. Upon inspection, found brake hard line from master cylinder was chaffed from adjacent fuel line, causing small pin-hole leak in brake line. When brakes were applied, brake fluid… Read more
Found identical problem per NHTSA action # ea08009 defect investigation. Constant loss of brake pressure. Warning lights indicated low brake fluid. Found fluid under car and in front left wheel-well. Upon inspection, found brake hard line from master cylinder was chaffed from adjacent fuel line, causing small pin-hole leak in brake line. When brakes were applied, brake fluid would spray out, resulting in insufficient braking pressure to hold vehicle at stops. Contacted mercedes dealership service department, they were un-aware of any problems associated with this. Estimated cost of repair was >$1000. ($112 for part, $975 for 6hrs labor) part number: a1634201526 purchased length of hardline myself at parts store. Constructed and installed my own replacement part for $155 including purchase of tools to complete job. *tr
NHTSA complaint #10254638
Jan 7, 2009service brakes, hydraulic, engine and engine cooling, electrical system
Tl*the contact owns a 2002 mercedes benz ml320. While driving less than 70 MPH, the front passenger side brake locked up and caused the vehicle to swerve into a median. The ABS warning indicator illuminated on the instrument panel at the same time the brakes locked. The contact never depressed the brake pedal nor the accelerator pedal for the brakes to lock. The vehicle… Read more
Tl*the contact owns a 2002 mercedes benz ml320. While driving less than 70 MPH, the front passenger side brake locked up and caused the vehicle to swerve into a median. The ABS warning indicator illuminated on the instrument panel at the same time the brakes locked. The contact never depressed the brake pedal nor the accelerator pedal for the brakes to lock. The vehicle was taken to the dealer and they stated that the yaw rate sensor failed. The repairs were scheduled under warranty. The failure and current mileages were 63,000. Updated 02/05/09 *bf the bas/esp light illuminated. The catalytic converter was cracked and the transmission electrical connector was leaking.. Updated 02/06/09.*jb
NHTSA complaint #10254094
May 4, 2007service brakes, hydraulic, electrical system, visibility
While driving, ml500 began to brake randomly . Also ABS turned on while stopping and accelerating. Also brakes were constantly screeching. Warning lights for ABS, bas, and washer fluid. Fluid level was fine. I told dealer about these problems before warranty had expired. They ran a diagnostics test and found nothing was wrong. They advised me to bring the vehicle in should the… Read more
While driving, ml500 began to brake randomly . Also ABS turned on while stopping and accelerating. Also brakes were constantly screeching. Warning lights for ABS, bas, and washer fluid. Fluid level was fine. I told dealer about these problems before warranty had expired. They ran a diagnostics test and found nothing was wrong. They advised me to bring the vehicle in should the same events occur. (the random breaking began to occur after warranty expired). The problem continued to persist and with the failure of ABS system, I brought the ml500 back to the service center. After two days, I retrieved the vehicle and the cost to repair was $1100.00. "conveniently" they found the same problems I spoke of before after the warranty was up. We had no choice but to pay to restore function to the vehicle. After taking it home we noticed that the there was no sound in the vehicle. The sound and navigation voice worked perfectly before getting service. And afterwards it did not. We called the service center, and they said to bring it back at our earliest convenience, and they will fix the problem. I assume that this was a mistake on their part. When I returned to restore the sound they approached me and told me that a "voice modulation unit" beneath the driver's seat had gone out, and that it would cost $750.00 parts and labor to repair. They tried to explain to me that this was just a coincidence, and that the unit was in no way related or circuit linked to the sensors they replaced. I
NHTSA complaint #10189784
Apr 5, 2006service brakes, hydraulic
Total brake failure on all four wheels directly in front of apolla high school during school hours. Mercedes says master cylinder failed. *jb
NHTSA complaint #10154644
Mar 21, 2006service brakes, hydraulic, power train
Dt*: the contact stated the vehicle had repeated problems with the brake assistance system. The problem presented itself by the illumination of the dashboard warning light. The vehicle was taken in seven times for service on the brake assistance system. The vehicle also had problems with the transmission. When the vehicle was parked, shut off, and restarted later, the… Read more
Dt*: the contact stated the vehicle had repeated problems with the brake assistance system. The problem presented itself by the illumination of the dashboard warning light. The vehicle was taken in seven times for service on the brake assistance system. The vehicle also had problems with the transmission. When the vehicle was parked, shut off, and restarted later, the gearshift became stuck in the park position. The vehicle was taken to a service dealer, and the dealer temporarily repaired both issues. The dealer determined that the two problems were related.*ak
NHTSA complaint #10153332
Nov 23, 2005service brakes, hydraulic
My concern is about safety. On two occasions I have sent my certified pre-owned 2002 Mercedes-Benz ml320 to the dealer with spongy brakes. In fact, under certain conditions, the brake pedal goes to the floor. I'm told that this is normal. I believe it to be unsafe. What should I do? *jb
NHTSA complaint #10143527
Oct 22, 2004service brakes, hydraulic
Warranty issues and/or manufacturing defects that should be covered by warranty. On october. 21, 2003 took my ml500 year 2002 to dealer for squealing and scraping brakes. Service department could not diagnose the problem the squealing and scraping and told me that brake disc and pads looks fine. However they advised me to buy newer version of brake pads, which would not… Read more
Warranty issues and/or manufacturing defects that should be covered by warranty. On october. 21, 2003 took my ml500 year 2002 to dealer for squealing and scraping brakes. Service department could not diagnose the problem the squealing and scraping and told me that brake disc and pads looks fine. However they advised me to buy newer version of brake pads, which would not squeal. I refused to buy brake pads, as they should be covered under warranty. I was not satisfied, therefore took the vehicle again next day (october 22,2003) and talked to the sales person from whom I bought the vehicle. He and service manager performed test drive. Dealership checked the brakes again and told the squealing and scrapping was due to a rock stuck between brake pads and disc. Since yesterday, I had driven my vehicle only 24 miles but now the pads and rotors have been damaged. Because of their negligence and unable to diagnose the problem, dealership charged me $348.04 for my 18 months old vehicle, that should have been covered under warranty. Dealership and mercedes benz did not honor the warranty. Same day, another customer came to the dealership with similar problem, his mercedes also had a rock stuck between brake pads and rotors. This appears to be a common defect in the mercedes that needs to be fixed for the safety of all. *ak
NHTSA complaint #10096242
Jun 29, 2004service brakes, hydraulic, air bags, seat belts, structure, equipment
Consumer stated he purchased a lemon. Since purchasing the vehicle it has been in the repair shop 4-5 times and each time at least a month. The air bag light came on and went off intermittently. When the consumer took the vehicle to the repair shop the air bag light went off and did not come back on, the doors would not open and the air conditioner malfunctioned. … Read more
Consumer stated he purchased a lemon. Since purchasing the vehicle it has been in the repair shop 4-5 times and each time at least a month. The air bag light came on and went off intermittently. When the consumer took the vehicle to the repair shop the air bag light went off and did not come back on, the doors would not open and the air conditioner malfunctioned. The mechanic was unable to resolve the problems. The vehicle was unsafe to drive. *ak the driver's seat belt was problematic, the cigarette lighters in the rear doors were inoperative, there was a hesitation upon acceleration, the left front low beam light would come on the display, the voice operation was hard to hear on both receiving and answering, the brakes felt soft, the trunk springs were broken and would not open properly, the cell phone was inoperative, and the check engine light had come on. (model/s500) *sc *jb
NHTSA complaint #10057758
Jan 23, 2004service brakes, hydraulic
Warranty issues and/or manufacturing defects that should be covered by warranty. *ph at the first 10,000 miles, the consumer noticed brake travel was too long and was advised by an service advisor that this was normal. However at less than 3,000 miles, the brakes were still not adequate and there was a squeaking noise from the rear brakes when braking. This time, the… Read more
Warranty issues and/or manufacturing defects that should be covered by warranty. *ph at the first 10,000 miles, the consumer noticed brake travel was too long and was advised by an service advisor that this was normal. However at less than 3,000 miles, the brakes were still not adequate and there was a squeaking noise from the rear brakes when braking. This time, the consumer was advised that the rear brake pads were gone and the rotors were scored due to too much city driving and the service advisor would not honor repairs under warranty. *tt *jb
NHTSA complaint #10057273
Jan 15, 2004service brakes, hydraulic
One day after washing the car, the rear brake sticks until pressing the gas pedal and force the brake to release. It makes a loud cracking noise during the force release. The noise is so loud that you may think you hit something from your bumper if you don't know the problem. Mbz said that's normal because of the rust overnight. They did took the brake apart, clean and put… Read more
One day after washing the car, the rear brake sticks until pressing the gas pedal and force the brake to release. It makes a loud cracking noise during the force release. The noise is so loud that you may think you hit something from your bumper if you don't know the problem. Mbz said that's normal because of the rust overnight. They did took the brake apart, clean and put them back together. They told me it's my responsiblity to drive the car after I wash to car to get rid of the excess water within the brake pads. Yesterday, it was a rainly day and I parked the car in the garage after driving. It happened again next day. I don't know how can I drive the car to get rid of the water when there is a rainly day. I'm still waiting for the manager to give me an answer and I don't think they will do anyting to resolve the problem since they claimed that this is normal for this brake.
NHTSA complaint #10070801
Nov 20, 2003service brakes, hydraulic
Dash board brake light went on and the brakes failed. *la
NHTSA complaint #10047273
Aug 25, 2003parking brake
Emergency brakes failed to release unless stepped on gas to forward or reverse. A day later after wheels were washed and dried up, emergency brakes would not release totally until stepping on the gas pedal. You can hear a loud noise(feel like hitting your bumper to something) when stepping on the gas pedal during the release of the brakes. Local dealer said their regional… Read more
Emergency brakes failed to release unless stepped on gas to forward or reverse. A day later after wheels were washed and dried up, emergency brakes would not release totally until stepping on the gas pedal. You can hear a loud noise(feel like hitting your bumper to something) when stepping on the gas pedal during the release of the brakes. Local dealer said their regional technician told them that this was normal. It's my repsonsibility to drive the car until the brake pads are dried up, then park the car. I told them it is dangerous for someone who may not know and thought the car won't move and step on the gas excessively. They did not seem care. I can not believe that they told me the pads have to be dried up before parking. I told them serveral times since I bought the car and they could not reproduce the problem until I called their roadside assistance and came to my house to verify it. They eventually confirmed the problem and reproduced the problem at their shop. However, they did not seem to comeup with a solution except to tell me that it's my repsonsibility to drive the car until the pads are dried up before I park the car. *ak
NHTSA complaint #10033499