Sep 9, 2026service brakes, forward collision avoidance
A malfunction of the sensotronic brake system (sbc) which is covered under mercedes campaign 2005110001 was amended to include model year 2006 cls 500 w219 (my model). While driving the vehicle sbc warning light came on and the vehicle slowed canceling acceleration and braking causing the vehicle to limp while in traffic. This is the second occurrence of this issue the first… Read more
A malfunction of the sensotronic brake system (sbc) which is covered under mercedes campaign 2005110001 was amended to include model year 2006 cls 500 w219 (my model). While driving the vehicle sbc warning light came on and the vehicle slowed canceling acceleration and braking causing the vehicle to limp while in traffic. This is the second occurrence of this issue the first only causing a loss of acceleration. This incident occurred 6 september 2026 with the first occurring 18 august 2026
NHTSA complaint #11763093
Oct 28, 2024service brakes, hydraulic
The contact owns a 2006 Mercedes-Benz cls500. The contact stated while driving approximately 20 MPH, the messages "reduced braking pressure, and “service required" was displayed and the vehicle experienced a loss in braking power. The contact was able to pull the vehicle over and proceed to inspect the vehicle. The vehicle was towed to an independent mechanic where the vehicle… Read more
The contact owns a 2006 Mercedes-Benz cls500. The contact stated while driving approximately 20 MPH, the messages "reduced braking pressure, and “service required" was displayed and the vehicle experienced a loss in braking power. The contact was able to pull the vehicle over and proceed to inspect the vehicle. The vehicle was towed to an independent mechanic where the vehicle was diagnosed. The contact was informed that the VIN on the svc (sensotronic-braking control unit) did not match with the VIN and that the contact had to bring the vehicle to a local dealer for repair. Upon becoming aware of the failure, the vehicle was towed to a local dealer where the vehicle was diagnosed; however, the contact was advised that the dealer could not replace the unit because the unit was not the correct unit for the vehicle. The contact was informed that the vehicle should not have an svc unit but instead should have an ABS unit. The vehicle was not repaired. The manufacturer was notified of the vehicle. The approximate failure mileage was 172,989.
NHTSA complaint #11622345
Feb 29, 2024service brakes
The contact owns a 2006 Mercedes-Benz cls500. The contact stated that while driving at undisclosed speeds, the brake pedal failed to depress properly. There was a message to “stop” displayed on the instrument panel. The vehicle was taken to an independent mechanic, who replaced the tls, but the failure recurred. The contact called the local dealer, who informed the contact… Read more
The contact owns a 2006 Mercedes-Benz cls500. The contact stated that while driving at undisclosed speeds, the brake pedal failed to depress properly. There was a message to “stop” displayed on the instrument panel. The vehicle was taken to an independent mechanic, who replaced the tls, but the failure recurred. The contact called the local dealer, who informed the contact that there were no recalls on the VIN. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 99,000.
NHTSA complaint #11574703
Jan 24, 2022service brakes
The 2006 mercedes benz cls500 was designed with a sbc braking system that uses a microcomputer to monitor the car and driver actions. The system sounds like a milestone achievement in braking technology, unfortunately its prone to failure. The entire system relies on electronics. Before long, wiring in the sbc braking system deteriorates, and suddenly the sbc system no… Read more
The 2006 mercedes benz cls500 was designed with a sbc braking system that uses a microcomputer to monitor the car and driver actions. The system sounds like a milestone achievement in braking technology, unfortunately its prone to failure. The entire system relies on electronics. Before long, wiring in the sbc braking system deteriorates, and suddenly the sbc system no longer functions. What happens is all of a sudden a warning light comes on and this message all in bright red saying, ‘brake malfunction. Ineffective braking,’” stepping on the brake, my foot was going down to the floor pretty easily. No resistance, no brakes. The atlantic motor car center receives hundreds of phone calls per year on this issue. Imagine yourself driving along and suddenly the dash goes red and you have no brakes, mercedes has extended the warranty on the sbc pump first to 10 years, then in 2018 to 25 years. Unfortunately, which happened to me and many others is when you take your car in to the dealer after the terrorizing experience they says they can not duplicate the problem or your car is not giving out a specific code. Although I had numerous fault codes relating to the sbc system, they informed me I did not have the code they wanted. The warranty is meant to prevent failures of the sbc system that result in no brakes. But when you take the car in they inform you it will be $3,000 dollars to replace the sbc pump. Just do some investigation on line to see what's going on. Does
NHTSA complaint #11448635
Dec 13, 2021service brakes
No notice brake failure. Coming up to the corner of my sub-division before making a right turn onto a busy 4 lane road, stepped on the brakes and nothing happened ! Swerved to the left to avoid hitting a jeep that was stopped in front of me also waiting for traffic to clear enough to make the right turn. My car traveled into the busy road, and its a miracle I didn't get… Read more
No notice brake failure. Coming up to the corner of my sub-division before making a right turn onto a busy 4 lane road, stepped on the brakes and nothing happened ! Swerved to the left to avoid hitting a jeep that was stopped in front of me also waiting for traffic to clear enough to make the right turn. My car traveled into the busy road, and its a miracle I didn't get killed by a truck traveling 50 MPH that might have t-boned my car on the driver side door. Car was beeping a loud noise and the instrument panel was lit up in red with the following alarm. Reduced braking power, visit workshop. Car would not accelerate over 5 MPH with the alarm blaring. Luckily was able to turn on emergency flasher and pull over to the side without getting hit. This is the first time I ever had a car that when you stepped on the brakes nothing happened. It scared the hell out of me and I refused to ever drive this car again. Absolutely, no warning that you no longer have brakes. I wonder how many people have been killed in accident from the same problem. Car is a 2006 mercedes benz cls 500.
NHTSA complaint #11443620
Oct 17, 2021electrical system, service brakes, fuel/propulsion system
Re 2006 mercedes benz cls500_ 211017_114326 on august 9, 2021, my brakes went out on the freeway when trying to dodge debris and other vehicles, when the brakes completely went out and caused me to run over major wood pallet debris, and scared for my.life to get to the far right lane to make it off te exit with no brakes whatsoever. And causing major under-carriage… Read more
Re 2006 mercedes benz cls500_ 211017_114326 on august 9, 2021, my brakes went out on the freeway when trying to dodge debris and other vehicles, when the brakes completely went out and caused me to run over major wood pallet debris, and scared for my.life to get to the far right lane to make it off te exit with no brakes whatsoever. And causing major under-carriage repairs. Rather than hit the cars on each side of me, all I could do at that point was get over lanes with no brakes, and make it off the exit before I killed myself and/or someone else. The damage done from the brakes going out, came to over $4000 in damage repairs to the under-carriage and left me without a vehicle for 45 days while in the shop this not only effected my income since the vehicle was used for lyft,, but I also was evicted from my apt. 30 days later, while my vehicle was in the shop, and unable to work to pay my rent. Once getting the car back these past few weeks, even though repairs were done, the car has continued to threaten my life and others, as the brakes continue to randomly go out at a light, on the freeway, behind a merging car, and ive come so close to having another bad accident. Not to mention since the accident, I am now getting gasoline fumes that seep throughout my car while driving, so profusely, its causing me migraines. But most of all the risk of a fire!
NHTSA complaint #11437059
Jul 31, 2020power train, electronic stability control (esc), service brakes
Brakes keep going out. Brake pedal going to the floor. Esp light comes on and car throttling to a slow creep even on the highway. Extremely dangerous for me and my wife and child.
NHTSA complaint #11342610
Mar 8, 2020service brakes
I was exiting the highway when I began to push on the break pedal it went all the way the the floor. Good thing it was a little traffic because I was going about 40 MPH so I was able to turn off the highway in the grass and stop. But this is a major safety issue and this could have well ended bad for me. Without warning the brakes just stopped working and gave the error 'depress brake pedal stop vehicle'
NHTSA complaint #11316895
Sep 25, 2019service brakes
Tl* the contact owns a 2006 Mercedes-Benz cls500. While driving 15 MPH, the 'depress brake pedal stop vehicle' warning indicator illuminated. The brake pedal was depressed all the way to the floorboard, but the vehicle did not stop. The vehicle coasted until it came to a complete stop. The vehicle was restarted and was able to function normally. Mercedes-Benz of south orlando… Read more
Tl* the contact owns a 2006 Mercedes-Benz cls500. While driving 15 MPH, the 'depress brake pedal stop vehicle' warning indicator illuminated. The brake pedal was depressed all the way to the floorboard, but the vehicle did not stop. The vehicle coasted until it came to a complete stop. The vehicle was restarted and was able to function normally. Mercedes-Benz of south orlando (4301 millenia blvd, orlando, fl 32839, (407) 374-0033) was contacted and informed the contact that there was no recall for the failure. The vehicle was not taken to a dealer or independent mechanic for diagnostic testing or repairs. The manufacturer was not made aware of the failure. The failure mileage was 133,726.
NHTSA complaint #11258011
Oct 21, 2018service brakes
Sensomatic braking control has been observed to have failed. Related brake warning light inhibits the car from braking properly or driving at a comfortable speed. Brake wire has been replaced and brake pads and the problem still persists. There is a recall on this that I was unaware existed. I need help. I'm in a dangerous situation that is unsafe for me and my family. Braking… Read more
Sensomatic braking control has been observed to have failed. Related brake warning light inhibits the car from braking properly or driving at a comfortable speed. Brake wire has been replaced and brake pads and the problem still persists. There is a recall on this that I was unaware existed. I need help. I'm in a dangerous situation that is unsafe for me and my family. Braking the vehicle takes considerable amount of pressure and seems to be delayed.
NHTSA complaint #11141636
Oct 16, 2018power train, service brakes, fuel/propulsion system
Bought the 2006 cls 500 2 years ago, since that second day I have issues with sbc module, I call mb dealer they told me my car was out of warranty, since the production date was 2004, okay after that I try several other mechanics and nobody have the star tool to fix up, the car is not safe to drive and I continue take the risk couple months until the fuel line starts leak on… Read more
Bought the 2006 cls 500 2 years ago, since that second day I have issues with sbc module, I call mb dealer they told me my car was out of warranty, since the production date was 2004, okay after that I try several other mechanics and nobody have the star tool to fix up, the car is not safe to drive and I continue take the risk couple months until the fuel line starts leak on the pump, this could generate a spark and burn my car, I call again mb dealer and they told me is probably unsafe to start the car. After all this years I parked the car and all my suspension was broke as well, call again the mb dealer they estimated $ 1800 to replace the air shocks, so I buy from arnott the same mb sell and I replace all 4, so the car is up again, next week I decide to sell the vehicle after driving in 3 years 9,000 miles only, try to move the car from the garage, guess what, my transmission go to limp mode because the breaks are not working, so far I decide to write in here to complain why a such beautiful car have so many issues and mb does not care for the old mb. I almost get on accident when my breaks complete frozen to the end !!!
NHTSA complaint #11140687
May 21, 2018service brakes
I was driving and the brake light came on and my brakes went straight to the floor which could have caused me to crash. Mb should have recalled this problem from this sensotronic module which they new about
NHTSA complaint #11096992
Jan 30, 2018service brakes
The Mercedes-Benz cls 500 has a issue on sbc module that occur on models like mine, this sbc system cannot stop the vehicle and mb know this occur and is replacement only, they do not replogram to clean the error.
NHTSA complaint #11065877
Dec 28, 2017service brakes
I was driving and the reduce braking light came on. I pulled over stopped my vehicle because it stated that I needed to do so, restarted the vehicle and tried to make it home. I began to loose control of the steering and even though I was pushing the brake pedal to stop, the pedal went to the floor. I was in rush traffic and so scared that I would hurt someone or myself. I… Read more
I was driving and the reduce braking light came on. I pulled over stopped my vehicle because it stated that I needed to do so, restarted the vehicle and tried to make it home. I began to loose control of the steering and even though I was pushing the brake pedal to stop, the pedal went to the floor. I was in rush traffic and so scared that I would hurt someone or myself. I recently had my brakes and rotors replaced, months in advance. I barely made it home and since then I have tried to take my vehicle to the shop but in doing so the same problem arose. Again, I was frighten to put it on the road I placed it back in the garage. Please help. I am not understanding why I am having these problems. I brought the car in september of 2013 and this is the only major issue I have had. I love my car. I also read that in 2006 some type of braking system was discontinued and that there was a recall on the sbc pump.
NHTSA complaint #11057260
Dec 22, 2017service brakes
Tl* the contact owns a 2006 Mercedes-Benz cls500. While driving 70 MPH, the "reduce brake" and "stop the vehicle" indicators illuminated. The vehicle was pulled over to the shoulder lane where it was able to restart and resume normal operation. The vehicle was taken to an independent mechanic where it was diagnosed that the sbc unit failed and needed to be replaced. The… Read more
Tl* the contact owns a 2006 Mercedes-Benz cls500. While driving 70 MPH, the "reduce brake" and "stop the vehicle" indicators illuminated. The vehicle was pulled over to the shoulder lane where it was able to restart and resume normal operation. The vehicle was taken to an independent mechanic where it was diagnosed that the sbc unit failed and needed to be replaced. The vehicle was not repaired. The local dealer was not contacted. The manufacturer was not notified of the failure. The failure mileage was approximately 170,000.
NHTSA complaint #11056058
Sep 7, 2017service brakes
I was entering onto a highway (100). At the point of the highway I was entering(from cty rd 81) it opens the highway to a 3rd lane on the right side of the highway. At the same place it opens the highway up, there is an immediate exit(42nd ave). As I am accelerating to highway speeds, just prior to the new lane availability that drivers must enter to get off on 42nd, my car… Read more
I was entering onto a highway (100). At the point of the highway I was entering(from cty rd 81) it opens the highway to a 3rd lane on the right side of the highway. At the same place it opens the highway up, there is an immediate exit(42nd ave). As I am accelerating to highway speeds, just prior to the new lane availability that drivers must enter to get off on 42nd, my car starts chiming and there's a red warning on my dash that states "stop, reduced braking power. Depress brake fully." or something quite similar. There is no shoulder, I'm going like 10 MPH, terrified. People are honking and trying to get over to get off on 42nd ave in a lane where I'm going 10 MPH and they were at a speed of approx 60 MPH(posted hwy speed). As I limp my car past this exit to a shoulder I then attempt to brake and have no braking power. I eventually rolled to a stop. Turned my vehicle off to determine my next move. I turned the vehicle back on to see what exactly the warning light said- there was nothing there. Tested my brakes a little on the shoulder and they were fine. I was able to drive the rest of the way to my destinations without any problems. This has since occurred a couple more times. Through a trip to the mechanic and thorough research it is determined the problem lies in my sensotronic brake pump. This is a pump that mercedes warrantied for 10 years due to this issue. This will occur to all other drivers of this vehicle that haven't had this part replaced. I never knew of the s
NHTSA complaint #11022130
Aug 11, 2017electrical system, service brakes
Tl* the contact owns a 2006 Mercedes-Benz cls500. While driving approximately 60 MPH, a message appeared on the instrument panel stating that the brake system had malfunctioned and the vehicle would not stop. The driver stopped the vehicle and shut off the engine. After restarting the vehicle, the message re-appeared. In addition, while operating the vehicle, the speedometer… Read more
Tl* the contact owns a 2006 Mercedes-Benz cls500. While driving approximately 60 MPH, a message appeared on the instrument panel stating that the brake system had malfunctioned and the vehicle would not stop. The driver stopped the vehicle and shut off the engine. After restarting the vehicle, the message re-appeared. In addition, while operating the vehicle, the speedometer would display inaccurate speeds. The failures were not diagnosed. The vehicle was not repaired. The manufacturer was notified of the failures, but no assistance was offered. The contact was informed that the vehicle was not included in NHTSA campaign numbers: 05v133000 (service brakes) and 08v303000 (electrical system). The contact stated that the vehicle experienced the same failures listed in the recalls. The local dealer was not notified. The failure mileage was unknown.
NHTSA complaint #11014702
Feb 19, 2017service brakes
I own a 2006 Mercedes-Benz cls 500 4 door I took to mb dealer to check for any open recall on sbc breaks and the the answer by mb was that my vehicle manufacture date was past the recall on the breaks. My vehicle that I pay top money is not safe to drive, is parked into my garage for almost 12 months, I keep looking for sale and when the mb dealer see the brake red light… Read more
I own a 2006 Mercedes-Benz cls 500 4 door I took to mb dealer to check for any open recall on sbc breaks and the the answer by mb was that my vehicle manufacture date was past the recall on the breaks. My vehicle that I pay top money is not safe to drive, is parked into my garage for almost 12 months, I keep looking for sale and when the mb dealer see the brake red light on dash, they walk away with less than $ 3,000 dollars for my vehicle that I paid $ 18,000. Mb estimated around $ 4700 to fix my vehicle. The sbc module needs to be replace complete to be reprogram again and be a safe drive vehicle. My wife e-500 also have the same issues and they said the same, but doe s not show any recalls on the sbc module. Just wondering why mb do not fix the problem and let the owners like me continue on the mb family.
NHTSA complaint #10955480
Nov 27, 2016service brakes
Vehicle sbs system. System at end of life according to code stored. Dealer advises that recall for my vehicle expired august 2015. Never received notice from mb. Costing me a fortune. Afraid to drive vehicle because of how sudden the system shuts down. Dealer tells me the system in the pump is breaking down.
NHTSA complaint #10928142
Aug 18, 2016service brakes
Tl* the contact owns a 2006 Mercedes-Benz cls500. While driving 65 MPH, the ABS warning indicator illuminated. The contact stated that the brakes failed to engage and was forced to drive off to the side of the road in order to stop the vehicle from crashing. The vehicle was towed to the contact's residence. The dealer was notified of the failure. The vehicle was not repaired. The failure mileage was 103,000.
NHTSA complaint #10896842
Apr 13, 2016service brakes
Tl* the contact owns a 2006 mercedes benz cls55. The contact stated that while depressing the brake pedal to stop the vehicle, the brake pedal traveled to the floorboard. The contact stated that the brakes had to be pumped in order to slow down and the emergency brake was engaged to stop the vehicle. The vehicle was taken to an independent mechanic where it was diagnosed that… Read more
Tl* the contact owns a 2006 mercedes benz cls55. The contact stated that while depressing the brake pedal to stop the vehicle, the brake pedal traveled to the floorboard. The contact stated that the brakes had to be pumped in order to slow down and the emergency brake was engaged to stop the vehicle. The vehicle was taken to an independent mechanic where it was diagnosed that the sbc pump had failed and would need to be replaced. The manufacturer was made aware failure. The failure mileage was 80,000. The VIN was not available.
NHTSA complaint #10855264
Feb 12, 2016service brakes
Tl* the contact owns a 2006 mercedes benz cls500. The contact stated that while driving at various speeds and attempting to depress the brake pedal, it traveled to the floorboard causing a greater stopping distance. The contact stated that the failure nearly caused accidents on several occasions. The vehicle was taken to the dealer where it was diagnosed that the sensotronic… Read more
Tl* the contact owns a 2006 mercedes benz cls500. The contact stated that while driving at various speeds and attempting to depress the brake pedal, it traveled to the floorboard causing a greater stopping distance. The contact stated that the failure nearly caused accidents on several occasions. The vehicle was taken to the dealer where it was diagnosed that the sensotronic brake control hydraulic pump had failed and would need to be repaired. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 177,000.
NHTSA complaint #10825826
Feb 12, 2016service brakes
Tl* the contact owns a 2006 mercedes benz cls500. The contact stated that while depressing the brake pedal at 70 MPH, the vehicle failed to stop and the reduce brake error message displayed. The contact was able to avoid an accident. The vehicle was towed to the dealer where it was diagnosed that the hydraulic pump and the sbc brake system failed and needed to be replaced. The… Read more
Tl* the contact owns a 2006 mercedes benz cls500. The contact stated that while depressing the brake pedal at 70 MPH, the vehicle failed to stop and the reduce brake error message displayed. The contact was able to avoid an accident. The vehicle was towed to the dealer where it was diagnosed that the hydraulic pump and the sbc brake system failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and mentioned that the vehicle was previously serviced under NHTSA campaign number: 05v133000 (service brakes, hydraulic). The failure mileage was 107,500.
NHTSA complaint #10825786
Feb 1, 2016service brakes
This vehicle is equipped with sensotronic brake control that has a service threshold. When this threshold is reached the brake system defaults to non power assisted hydraulic mode to the front wheels only. This occurs without any prior warning and results in increased stopping distance. I have sent a copy of the mercedes service bulletin s142.46-p-0012a which addresses this… Read more
This vehicle is equipped with sensotronic brake control that has a service threshold. When this threshold is reached the brake system defaults to non power assisted hydraulic mode to the front wheels only. This occurs without any prior warning and results in increased stopping distance. I have sent a copy of the mercedes service bulletin s142.46-p-0012a which addresses this issue. Mercedes stopped installing this system in 2006. At the very least, mercedes should issue a mandatory recall to interrogate these vehicles with star das to determine how close to the service threshold the sbc unit is and replace them at the dealer's expense. The warranty has been extended to 10 years, unlimited mileage, so mb knows of the defect. Unfortunately, many vehicles are outside this 10-year window, yet the problem should be fixed. This is a major safety issue that needs to be addressed.
NHTSA complaint #10823623
Nov 1, 2015service brakes, fuel/propulsion system
The vehicle was sended to inspection due to a "brake warning" started showing at the gauges control panel. Mercedes benz dealer service manager indicates that they not have a correct tool to recode to actualize the brake system and /or fix the problem at that time. Three visits and several phone calls been made to the dealer. The service advisor is always with other customer.… Read more
The vehicle was sended to inspection due to a "brake warning" started showing at the gauges control panel. Mercedes benz dealer service manager indicates that they not have a correct tool to recode to actualize the brake system and /or fix the problem at that time. Three visits and several phone calls been made to the dealer. The service advisor is always with other customer. I'm stop to drive my vehicle, because I never knew how deep is the problem. Doing a visual inspection I observed that the rear brake pads are not applying good enough, the surfaces of the rotors are different. The mercedes benz dealer representative still not notify me. This is a safety issue. This vehicle is not making any noise or have any vibration during braking. But I notice that is braking more at front than the rear. *brake fluid is been changed by the dealer. Service advisor stated that this car have an "extended recall" for brake mal-function/on different areas, but nothing is been done to fix the codes: hydraulic faults/c25d0/c2514/c249f/c22b5 & c223c. This may be the ABS control box fault. After been waiting from 07:30 - 13:00 (5.5 hrs) on my last visit. I received my car back just with few words front the advisor; " we need to order a part to re-coded your system, we contact you later (21 aug 2015). Note: recall # 05v133000 did you can assist me with this problem/ situation? Thanks in advance. V/ respectfully, mr. W.ortiz
NHTSA complaint #10787494
Sep 12, 2014service brakes
Tl* the contact owns a 2006 mercedes benz cls500. While driving approximately 45 MPH, the "braking power insufficient" warning indicator illuminated. The contact had to depress the brake pedal to the floorboard in order to stop the vehicle. The vehicle was not diagnosed or repaired. The manufacturer was notified. The approximate failure mileage was 86,000.
NHTSA complaint #10632672
Nov 26, 2012service brakes
Tl* the contact owns a 2006 mercedes cls500. The contact stated that she believes the vehicle was included in recall NHTSA campaign id number: 05v133000 (service brakes, hydraulic). The vehicle was taken to the dealer for the recall repair. The technician stated the sbc unit needed to be replaced but was not covered under the recall. The technician stated the only part covered… Read more
Tl* the contact owns a 2006 mercedes cls500. The contact stated that she believes the vehicle was included in recall NHTSA campaign id number: 05v133000 (service brakes, hydraulic). The vehicle was taken to the dealer for the recall repair. The technician stated the sbc unit needed to be replaced but was not covered under the recall. The technician stated the only part covered was the sbc pump. The contact was waiting to hear back from the manufacturer for possible assistance. The vehicle was not repaired. The approximate failure mileage was 59,767.
NHTSA complaint #10486053
Jul 5, 2012electronic stability control (esc), service brakes
Driving at steady speed, tried to brake- brake pedal sank to the floor, driver's side front wheel locked up- no apparent braking actually happened, despite pressing on the brake pedal. Locking up of driver's side front wheel caused total loss of vehicle control, causing a 360 degree spin. Car malfunctioned afterwards, could not drive until turned off the engine and restarted… Read more
Driving at steady speed, tried to brake- brake pedal sank to the floor, driver's side front wheel locked up- no apparent braking actually happened, despite pressing on the brake pedal. Locking up of driver's side front wheel caused total loss of vehicle control, causing a 360 degree spin. Car malfunctioned afterwards, could not drive until turned off the engine and restarted the car. There were no warning lights afterward- no brake light, no check engine light, no error message in the dashboard relating to brake failure. *tr
NHTSA complaint #10464371
Jun 21, 2012fuel system, gasoline, electrical system, air bags, service brakes
Tl* the contact owns a 2006 mercedes benz cls 500. The contact stated while in his home, he could smell gasoline fuel leaking from the vehicle while parked in the residential garage. The contact was unable to locate a fuel leak and took the vehicle to the dealer for inspection. The dealer advised the contact that the fuel pump needed to be replaced. The vehicle was not… Read more
Tl* the contact owns a 2006 mercedes benz cls 500. The contact stated while in his home, he could smell gasoline fuel leaking from the vehicle while parked in the residential garage. The contact was unable to locate a fuel leak and took the vehicle to the dealer for inspection. The dealer advised the contact that the fuel pump needed to be replaced. The vehicle was not repaired. The manufacturer was not notified. The failure mileage was 48,000.... Updated 08/15/12 *bf updated 08/16/2012 *js
NHTSA complaint #10462549
Feb 9, 2010service brakes, hydraulic
Brakes on 2006 mbz cls 500. Replaced twice with brand new brakes from mbz dealer, drove less than 3000 miles, brakes squeak like a train three weeks after each installation. Dealer wants to wash their hands by saying its normal. How can brand new brakes squeak twice after new replacement and very few miles of driving? They really need a check up and recall. Its ridiculous for… Read more
Brakes on 2006 mbz cls 500. Replaced twice with brand new brakes from mbz dealer, drove less than 3000 miles, brakes squeak like a train three weeks after each installation. Dealer wants to wash their hands by saying its normal. How can brand new brakes squeak twice after new replacement and very few miles of driving? They really need a check up and recall. Its ridiculous for new brakes to squeak that loud, you can hear me from another corner. *tr
NHTSA complaint #10307695
Aug 14, 2006service brakes, hydraulic
Dt*: the contact stated when applying the brakes there was a grinding and squeaking noise and diminished stopping power. There were no lights illuminated on the dash. The dealership was contacted.
NHTSA complaint #10165432