CarProblemsDB

2013 Jeep Wrangler stability control problems

18 owners reported stability control problems — 3% of all 657 complaints about the 2013 Jeep Wrangler.

Stability control complaints by Jeep Wrangler year

20203
20199
201846
20177
201613
201514
201410
201318
201230
20118
20109
20099
200822
200713
20061
20052
20041
20011

What owners report

Jun 10, 2020steering, electronic stability control (esc)

I'm experiencing the death wobble and I wanted to see if there's a way it can be fix or if a recall is out for this. *tr

NHTSA complaint #11328261
Aug 6, 2019power train, vehicle speed control, electronic stability control (esc)
The vehicle keeps losing power at the most inopportune times (passing a vehicle; in a construction zone with no shoulder; on a highway). I have almost gotten into 4 accidents b/c of this problem. Whenever the vehicle goes faster than 70 MPH...power is lost. It continually throws off a code of 0369. The dealership has replaced the following to try to fix the problem:… Read more

The vehicle keeps losing power at the most inopportune times (passing a vehicle; in a construction zone with no shoulder; on a highway). I have almost gotten into 4 accidents b/c of this problem. Whenever the vehicle goes faster than 70 MPH...power is lost. It continually throws off a code of 0369. The dealership has replaced the following to try to fix the problem: replaced ABS system; replaced stability control system; replaced oil filter housing; replaced the cam twice; swapped the cam; replaced the cam phaser; replaced all 4 cam phasers; re-flashed the PCM; replaced the PCM. Today it goes in to the dealership for the 10th time to try to get it fixed. It is a death trap to all that share the road with it, not to mention extremely unreliable. It has never been off-roaded and is well maintained.

NHTSA complaint #11242011
May 7, 2019electronic stability control (esc), service brakes
After sitting idle all night, started vehicle in morning and ABS and ESC lights came on. I was unable to accelerate as the rear brakes were being engaged by a faulty sensor. I shifted into neutral and back to drive and lights went out and back to normal operation. I pulled out onto the main thoroughfare and the Jeep stuttered upon acceleration and felt like it was losing… Read more

After sitting idle all night, started vehicle in morning and ABS and ESC lights came on. I was unable to accelerate as the rear brakes were being engaged by a faulty sensor. I shifted into neutral and back to drive and lights went out and back to normal operation. I pulled out onto the main thoroughfare and the Jeep stuttered upon acceleration and felt like it was losing power before it stopped. Both lights came back on. After shifting back to neutral, I was able to get back onto the street and to the dealer for service. This is the second time this condition occurred in this vehicle. In july of 2016 the right rear wheel speed sensor was replaced by fitzgerald Jeep in clearwater. Codes c1035 and c1049 were present at the time of the repair. This faulty sensor could have caused an accident with injuries, at best, or a fatality/fatalities at worst. The computer program that allows a faulty sensor to override the drivers action is a malfunction that needs to be addressed.

NHTSA complaint #11205978
May 2, 2019vehicle speed control, electronic stability control (esc)
While driving with cruise control engaged on the highway at roughly 80mph, the cruise control kicks off. Check engine light displays and the ESC light comes on. Vehicle loses power and decelerates on its own. Have to floor the gas pedal to keep the vehicle moving. Experiences momentary bursts of speed but then speed declines again although the gas pedal is still pressed to… Read more

While driving with cruise control engaged on the highway at roughly 80mph, the cruise control kicks off. Check engine light displays and the ESC light comes on. Vehicle loses power and decelerates on its own. Have to floor the gas pedal to keep the vehicle moving. Experiences momentary bursts of speed but then speed declines again although the gas pedal is still pressed to the floor. I believe this is attributed to the clockspring assembly but my vehicle was not included in the recall. Can my VIN be added so I can get this issue resolved?

NHTSA complaint #11205240
← All 2013 Jeep Wrangler problems & recalls