Aug 16, 2026vehicle speed control, service brakes
My vehicle has experienced a complete failure of the ABS control module. A dealer diagnosis confirmed internal module failure. The symptoms are: - all ABS system warning lights illuminated (ABS, traction control, brake, sway bar) - odometer and speedometer stop working while driving - all brake lights remain on continuously - vehicle exhibits erratic shifting / rough braking … Read more
My vehicle has experienced a complete failure of the ABS control module. A dealer diagnosis confirmed internal module failure. The symptoms are: - all ABS system warning lights illuminated (ABS, traction control, brake, sway bar) - odometer and speedometer stop working while driving - all brake lights remain on continuously - vehicle exhibits erratic shifting / rough braking this is a documented safety defect affecting many chrysler/dodge/Jeep owners where the dealer confirms the ABS module is defective but cannot repair due to the part being on national backorder with no eta. I am being told the part is backordered indefinitely. I am left driving an unsafe vehicle with no functioning ABS, stability control, or accurate speed/odometer reading, or parking a vehicle I am still paying for and insuring. I am formally requesting: 1. Immediate provision of a replacement ABS module, or a loaner/rental vehicle at fca's expense until repair
NHTSA complaint #11757235
Jul 2, 2026air bags, vehicle speed control, service brakes
Most of the dash lights are on scan code u1412. Says traction control not working, ABS not working, speedometer not working, and airbags not working. The power control module (PCM) needs replaced. A known issue with the Jeep Wrangler jks. No one stocks the parts and used ones are way over priced. How can Jeep not have to replace it or at least stock a replacement part that has the issues resolved?
NHTSA complaint #11748027
Jun 17, 2026service brakes
ABS module failed the company no longer makes the chips to repair this module
NHTSA complaint #11744768
Mar 19, 2026service brakes
ABS module fails with c2200 code. No replacement parts are available, hence driving with no ABS (manual brakes). Jeep needs to address the nationwide backlog on ats moudles so proper repairs can be made and Jeep owners have the peace of mind that the ABS is functioning properly.
NHTSA complaint #11725651
Mar 13, 2026electrical system, unknown or other, service brakes
ABS module failure. Unable to get replacement. Manufacturer refuses to provide & unable to use used ones due to being programed to VIN#. It has been over 2 years and no resolution in site.
NHTSA complaint #11724075
Dec 10, 2025service brakes
Faulty ABS module. Dealer is unable to get part to fix. Car is dangerous to be driven with issue.
NHTSA complaint #11704160
Nov 5, 2025service brakes
Anti-lock brake system failure noted by dash board lights indicating system failure.
NHTSA complaint #11697712
Jul 23, 2025steering, vehicle speed control, service brakes
ABS failing. Loss of traction control & possible brake failure. Vehicle manufacturer failing to provide parts.
NHTSA complaint #11675581
Jun 26, 2025service brakes
ABS, traction control, & brake warning lights have come on due to issues with the ABS sensors. Repairs unavailable due to unavailability of parts.
NHTSA complaint #11669443
Jan 14, 2024service brakes
The ABS control module is reporting a dtc code c2200 indicating an ABS module internal failure. The instrument panel warning lights for esp, bas, ABS and the traction control are all continuously lit. This problem is continuous but has not been confirmed or inspected by a dealer. Independent service center, police or insurance representatives. It is, however, a well known… Read more
The ABS control module is reporting a dtc code c2200 indicating an ABS module internal failure. The instrument panel warning lights for esp, bas, ABS and the traction control are all continuously lit. This problem is continuous but has not been confirmed or inspected by a dealer. Independent service center, police or insurance representatives. It is, however, a well known issue reported on Jeep owner forums as an ABS dashboard christmas tree. I have not yet had an ABS related accident but it is extremely concerning that there is an internal ABS module failure that could cause an accident. I have attempted to replace the ABS module, part 68067458aa, but I am told this part is not available due to a hold for engineering review. I was told the engineering review should be completed by march 20 but until then I am unable to obtain a new replacement part.
NHTSA complaint #11565431
Feb 5, 2023power train, service brakes, engine
When starting the vehicle the check engine light comes on. Including the low tire pressure sensor comes on. The tires have been repaired yet the pressure system still says low. The car when shortly after it's been turned on only going several miles an hour and staying about 2rpms starts to kick forward in a abrupt motion as if it wants to accelerate. Sometimes it's a hit or… Read more
When starting the vehicle the check engine light comes on. Including the low tire pressure sensor comes on. The tires have been repaired yet the pressure system still says low. The car when shortly after it's been turned on only going several miles an hour and staying about 2rpms starts to kick forward in a abrupt motion as if it wants to accelerate. Sometimes it's a hit or miss to start the car so I have to put it in neutral to start it. In conclusion everytime the vehicle starts to move from a complete stop or braking a loud clanking noise repeats a 2-3 times (clank,clank,clank) continues then stops after driving continually, then repeats after every stop that is made. I'm not sure what to make of it but my guess it has to do with the braking system even though no warning lights for brakes have come up.
NHTSA complaint #11505618
Nov 21, 2022air bags, service brakes, forward collision avoidance
Airbag, brakes, traction control inoperative with c2200-00 code for internal brake control fault. Vehicle has 58k miles garage kept, now has no safety components working. It is a known problem apparently all over the internet. Why isn't this being addressed.
NHTSA complaint #11494421
Sep 21, 2022air bags, unknown or other, service brakes
Code c2116 - ABS pump motor supply low. This error code has been occurring for the past year. I have no ABS brake function, no air bag function, and no traction control function. The part from Jeep chrysler, ABS module, has been on back order for 1 year. I believe it is dangerous for me to be driving this vehicle. One year on back order, please do something and help.
NHTSA complaint #11485629
Feb 12, 2020service brakes
While driving vehicle at approx 45mph in the rh lane approaching an intersection with an illuminated green right-turn arrow(my lane), a vehicle in the same lane, traveling same direction, suddenly stopped at the green light at the intersection. I immediately applied hard pressure to brake pedal, only to have it slam straight to the floor-board with very little braking… Read more
While driving vehicle at approx 45mph in the rh lane approaching an intersection with an illuminated green right-turn arrow(my lane), a vehicle in the same lane, traveling same direction, suddenly stopped at the green light at the intersection. I immediately applied hard pressure to brake pedal, only to have it slam straight to the floor-board with very little braking action. I was able to quickly down-shift and apply parking brake in time to avoid collision with stopped vehicle. I carefully drove vehicle to my home, approx 3 miles from incident intersection. Upon inspection I noted brake master-cylinder empty (it was topped-off to "max" line when checked evening prior), and hydraulic fluid sprayed all-around right (passenger)-side front inner wheel and puddled/dripping at banjo-bolt. You-tube research found a similar situation with a Jeep 2 model years older than mine. Link to video: https://www.youtube.com/watch?v=nvdzj874xum&list=pldw3mie2v4tcrduua9d8rbclqv8qa1mfb&index=2&t=1230s when I removed the right brake hose assembly, the metal crimp-on fitting to the flex-hose was completely disintegrated by corrosion. I replaced the left brake hose assembly as well, and found nearly as-severe corrosion on the metal crimp-on fittings though no leakage had occurred from there during this incident. See attachments for digital pics taken throughout the repair process, and excerpts from the maintenance logbook I maintain on this vehicle. I have another, newer (2014) jee
NHTSA complaint #11308769
Jul 15, 2019air bags, electronic stability control (esc), service brakes
Tl* the contact owns a 2010 Jeep Wrangler. The contact received a recall notification for NHTSA campaign numbers: 16v290000 (service brakes, air, electronic stability control) and 18v021000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time to repair the vehicle. Jake sweeney chrysler Jeep (85 w kemper rd, cincinnati, oh 45246) confirmed… Read more
Tl* the contact owns a 2010 Jeep Wrangler. The contact received a recall notification for NHTSA campaign numbers: 16v290000 (service brakes, air, electronic stability control) and 18v021000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time to repair the vehicle. Jake sweeney chrysler Jeep (85 w kemper rd, cincinnati, oh 45246) confirmed that parts were not available to perform the recall repairs. The manufacturer was not notified. The contact also stated that an unknown warning indicator was illuminated. The failure mileage was unknown. Parts distribution disconnect.
NHTSA complaint #11232088
May 18, 2019service brakes
The front brake lines have an insulator that covers the hard pipe to rubber connection. This insulator allows moisture to collect between it and the metal fitting that connects the two different line materials. The connection rots through and then begins to leak. The rear lines do not have this insulator on that connection and they are in perfect condition. The insulator… Read more
The front brake lines have an insulator that covers the hard pipe to rubber connection. This insulator allows moisture to collect between it and the metal fitting that connects the two different line materials. The connection rots through and then begins to leak. The rear lines do not have this insulator on that connection and they are in perfect condition. The insulator appears to be the cause of the premature failure. I noted the loss of brake fluid while doing other maintenance on the Jeep.
NHTSA complaint #11208394
Mar 2, 2019electronic stability control (esc), service brakes
All the break lights came on at one time (esp, bas, ABS) and the traction control will not go off. I was slowing down at a stop sign in a school parking lot. No rain or other weather events occured, on dry pavement
NHTSA complaint #11183641
Nov 18, 2018service brakes
Took the vehicle in for a yearly inspection and garage told me there was a problem with the brake lines rubbing on the tires when the wheels were turned all the way. Mechanic showed me the wear and asked if I put any after market parts on the vihicle. I confirmed everything was stock. Told me there should be a recall being this was a manufacturing problem where the brake lines… Read more
Took the vehicle in for a yearly inspection and garage told me there was a problem with the brake lines rubbing on the tires when the wheels were turned all the way. Mechanic showed me the wear and asked if I put any after market parts on the vihicle. I confirmed everything was stock. Told me there should be a recall being this was a manufacturing problem where the brake lines were routed too close to the tires and almost wore through the brake lines. Took it to the dealership to have lines rerouted and no recalls were issued for this problem. Did some research and found other similar complaints on several Jeep forums. Dealership said they had never heard of such problems.
NHTSA complaint #11152292
Jul 28, 2018service brakes
Breaks: when the Jeep is off the pedal will pump up with pressure but when im driving the pedal goes to the floor if I just press it one time.
NHTSA complaint #11114270
May 17, 2018service brakesCrash
The emergency brake on my 2010 Wrangler does not hold the vehicle on any sort of incline. The virginia code for a parking/ emergency brake states that it must stall the vehicle in 2nd gear (it does) but the brake will not maintain the position of the vehicle on the slightest incline. I'm concerned that the vehicle may roll away into the road and cause harm to others.… Read more
The emergency brake on my 2010 Wrangler does not hold the vehicle on any sort of incline. The virginia code for a parking/ emergency brake states that it must stall the vehicle in 2nd gear (it does) but the brake will not maintain the position of the vehicle on the slightest incline. I'm concerned that the vehicle may roll away into the road and cause harm to others. Furthermore, if I were to be in the vehicle then I may become trapped with it rolling in to traffic. This is a common issue on the early 2007-2017 body style Wrangler and needs attention before it causes serious harm.
NHTSA complaint #11096635
Feb 9, 2017exterior lighting, service brakes
First, I was driving on the highway and hit the brakes, when the vehicle locked all the brakes completely, the vehicle started skidding almost causing an accident because I lost control of the vehicle. A few weeks later, I was driving up the hill when all the dash lights lighted up, I stopped the vehicle and turned it off but they did not went off . I went to the dealer and… Read more
First, I was driving on the highway and hit the brakes, when the vehicle locked all the brakes completely, the vehicle started skidding almost causing an accident because I lost control of the vehicle. A few weeks later, I was driving up the hill when all the dash lights lighted up, I stopped the vehicle and turned it off but they did not went off . I went to the dealer and they told to replace the ABS module (68067458aa) costing $215.00 plus $160 on labor. They also told me that a few customers are complaining about the same issue. The vehicle is also turning off the headlights at night. Right know the problem is intermittent. The check engine code is b162f, right low beam control. According to the dealer, the tipm needs to be replaced, it cost around $400. When I looked in the internet, there are several cases of that issue since 2010.it creates a possible hazard driving at night.
NHTSA complaint #10953661
Jul 28, 2015structure, service brakes, engineFire
I was driving my Jeep to work when all the sudden white smoke entered the cap. I rolled the window down to vent the smoke and saw flames at my feet. I pulled the Jeep over to the side of the highway just in time for the brakes to fail. After putting the emergency brake on so it would roll into another car I jumped out of the car just in time to see the flames eat the hood… Read more
I was driving my Jeep to work when all the sudden white smoke entered the cap. I rolled the window down to vent the smoke and saw flames at my feet. I pulled the Jeep over to the side of the highway just in time for the brakes to fail. After putting the emergency brake on so it would roll into another car I jumped out of the car just in time to see the flames eat the hood of my Jeep and work its way back through my entire vehicle. I watched as the fire department put out the fire over and over and over. Since it had a full tank of gas my Jeep was distroyed. I put $70,000 of parts into my Jeep and it was all eaten by a fire in 20 minutes. I got the oil changed done at the dealership and was never told about a recall. I never recieved any piece of mail notifying me of any recall. I didn't know about the fire issues until I started to research what the problem might have been. The fire department said that they will investigate it but that there really isn't anything left of the Jeep to find the origin. I have video of the fire when it was occuring as well as pictures of the before, during, and after the fire....updated 09/22/15 *bf updated 12/11/2017*cn
NHTSA complaint #10744081
Jun 10, 2015electrical system, unknown or other, service brakesFire
While the vehicle was driven about 20mph, first on line to a traffic light and on about 20 t0 25 feet before the intersection and light was red, and when the brake was applied it did not stop and the vehicle kept moving and it was stopped by the emergency brake. A burning smell got inside the vehicle and people stopped yelling that the vehicle was on fire. When the hood was… Read more
While the vehicle was driven about 20mph, first on line to a traffic light and on about 20 t0 25 feet before the intersection and light was red, and when the brake was applied it did not stop and the vehicle kept moving and it was stopped by the emergency brake. A burning smell got inside the vehicle and people stopped yelling that the vehicle was on fire. When the hood was opened and the fire put out we notices that the fire started at the brakes pump sensor. It burned all the wiring around there to include plastic cover of left hand side wheel, the steering column rubber joint, sensors, the hood and other parts in that side.
NHTSA complaint #10724655
May 15, 2014steering, suspension, service brakesCrash
Vehicle was parked in front of a house . I left the vehicle in 1st gear then set the parking brake and turned the wheels into the curb to prevent roll back and I got out of the vehicle. I went inside and the vehicle rolled down a hill and into a house. When the police came they found it still in gear and the emergency brake was still on . *tr
NHTSA complaint #10588514
May 16, 2012service brakesCrash
I tried to stop at a traffic light. I had about 150 to 200 feet to the back of the next vehicle. I was traveling about 40 MPH. I depressed the brake pedal, it went all the way to the floor and the brakes were pulsating. The vehicle would not stop and I release and pressed the brakes again. The vehicle never stopped and continued to hit the vehicle in front of me. The police… Read more
I tried to stop at a traffic light. I had about 150 to 200 feet to the back of the next vehicle. I was traveling about 40 MPH. I depressed the brake pedal, it went all the way to the floor and the brakes were pulsating. The vehicle would not stop and I release and pressed the brakes again. The vehicle never stopped and continued to hit the vehicle in front of me. The police would not let me drive it away from the scene, the dealer insisted that I pay a tow truck to bring it back to the dealer and after the second day I have no transportation or any hope of any? I want to know what failed, can or will they fix it and what can I do to get to work now? I bought it new in oct 2010 and it has 35286 miles on it. Well within warrenty.
NHTSA complaint #10458751
Mar 14, 2012service brakes, hydraulic, engine and engine coolingFire
Stock 2010 Jeep Wrangler unlimited rubicon ~25,000 miles while driving ~ 25mph on a city street, brakes failed and I drove through a stop sign - I noticed smoke coming from the dash and attempted to pull the vehicle to the side of the road. Before I could, the power steering failed and I noticed flames from the drivers side window. I jumped from the Jeep. Fire services were… Read more
Stock 2010 Jeep Wrangler unlimited rubicon ~25,000 miles while driving ~ 25mph on a city street, brakes failed and I drove through a stop sign - I noticed smoke coming from the dash and attempted to pull the vehicle to the side of the road. Before I could, the power steering failed and I noticed flames from the drivers side window. I jumped from the Jeep. Fire services were on scene w/I 2 minutes and Jeep was completely engulfed in flames (around engine compartment) w/I 30 seconds. *tr
NHTSA complaint #10451570
Jun 7, 2011parking brake, equipmentCrash
In april 2011, my Jeep went in for service at herb chambers. There were safety recalls that needed to be fixed and I expressed my concern to the service associate about my parking brake being loose and not properly adjusted. When I returned to the dealership the diagnosis I received from the service associate was that a massachusetts registered safety inspector examined my… Read more
In april 2011, my Jeep went in for service at herb chambers. There were safety recalls that needed to be fixed and I expressed my concern to the service associate about my parking brake being loose and not properly adjusted. When I returned to the dealership the diagnosis I received from the service associate was that a massachusetts registered safety inspector examined my parking brake and it was functioning properly. In may 2011, approximately a month after my vehicle was in for service, I parked my vehicle in its parking spot at my house and when I returned to my vehicle five minutes later it had rolled into the woods. When the Jeep rolled into the woods it hit three trees resulting in the rear passenger side fender ripping off. When I contacted customer service at Jeep they stated I needed to file a claim through my insurance company and there was nothing they could assist me with. A claim was filed through my insurance company and chrysler company. Currently the Jeep is being repaired through my insurance company. I feel that once the body work is complete on my Jeep the mechanical parts of the Jeep will still be defective. I am concerned that the parking brake will fail again and could significantly damage property or a bystander. Chrysler sent out a private contractor, hank sullivan, who inspected the parking brake. When requested to be on site of his investigation of my vehicle my requested was denied. Once his investigation was complete I requested paperwork to verif
NHTSA complaint #10405511