CarProblemsDB

2005 Jeep Wrangler electrical system problems

20 owners reported electrical system problems — 3% of all 650 complaints about the 2005 Jeep Wrangler.

Electrical system complaints by Jeep Wrangler year

20263
202540
2024432
2023201
2022175
2021310
2020183
2019153
2018269
201745
201657
201582
201482
2013104
2012148
201184
201086
200935
2008178
200782
200626
200520
200412
20039
20027
200137
200023

What owners report

Jul 14, 2021power train, electrical system, engine

The dashboard will display odd behavior and all of a sudden the ignition will cut. Total loss of power. This has happened in the past with children in the vehicle. Very dangerous. Resetting the key will reset but it is random.

NHTSA complaint #11424836
Jun 28, 2021electrical system, engine
Engine failed, speedometer, tach went to 0, all gauges went to 0, power steering failed after I declutched and then coasted to a full stop (power brakes failed but still had some brake input) safely on the shoulder of an off ramp. (this not the first time this has happened, however it was the first time pulling a full trailer, so I drive as if it could happen again) vehicle… Read more

Engine failed, speedometer, tach went to 0, all gauges went to 0, power steering failed after I declutched and then coasted to a full stop (power brakes failed but still had some brake input) safely on the shoulder of an off ramp. (this not the first time this has happened, however it was the first time pulling a full trailer, so I drive as if it could happen again) vehicle was at branhaven Jeep in branford, ct last july @ 64429 miles... They were unable to duplicate. It is now at gengras Jeep in east hartford, ct, same story. I've asked gengras to replace the ignition switch again. I have the ignition switch from branhaven which I found the copper plate worn off to steel and evidence of arcing on the contacts

NHTSA complaint #11422633
Oct 22, 2020electrical system

Ecu stoped working no reason.

NHTSA complaint #11365817
Sep 29, 2020electrical system

The PCM has a known high failure rate due to the vibration. The components are covered in a resin that you can not remove. The PCM is 500-1300 to get a repaired and reprogramed one. I have a 2005 and the PCM has failed and gives bad performance and does not run on teh 14.7 stokes for air/fuel/ it dumps fuels and I do not think it meets emisson levels in this condition.

NHTSA complaint #11361908
Mar 26, 2018electrical system
005-2006 Jeep wranglers are incurring an apparent large number of PCM/ecu failures (as evidenced in many online forums and a high backlog of PCM orders which Jeep/chrysler is unable to fill or provide an eta for). The failure of the PCM reveals itself in many ways including emissions system failures (and resultant vehicle inspection failures I will add), transmissions failing… Read more

005-2006 Jeep wranglers are incurring an apparent large number of PCM/ecu failures (as evidenced in many online forums and a high backlog of PCM orders which Jeep/chrysler is unable to fill or provide an eta for). The failure of the PCM reveals itself in many ways including emissions system failures (and resultant vehicle inspection failures I will add), transmissions failing to shift, hard forceful transmission shifts with vehicle lunges and more. On my vehicle specifically the transmission codes are coming on and the vehicle will randomly not shift out of second gear and randomly shifts to neutral while driving at highway speeds and presents itself as a safety hazard when entering high speed freeways and interstates. To the PCM and further online investigation indicates this a frequent and recurring issue. When I attempted to replace the PCM through Jeep/chrysler I am unable to because the part is ba cklogged. I have placed a pricey $1600 order for the part but thus far over 3 months my vehicle has not been able to obtain a working replacement part based on the large number and type of issues reported online with this PCM I am left wondering why it is not a safety, emissions and/or recall issue.

NHTSA complaint #11081325
Nov 27, 2017power train, electrical system, engine

Over a period of several days the vehicle started shifting hard and eventually went into "limp" mode and started throwing different codes for various sensors. After many visits to different mechanics I researched the problem myself and pinpointed the PCM as the problem.

NHTSA complaint #11048589
Jun 26, 2017electrical systemFire

2014: dash and rear lights stopped working. Had to replace multi-function switch. Module and wiring melted and fused together. 2017: during install of new stereo, mechanic discovered multi-function switch and module melted again. Replaced all wiring with heavier gauge, replaced all bulbs with lower wattage leds. Wondering when next electrical problem will surface.

NHTSA complaint #11001549
Oct 16, 2014electrical system, exterior lighting

Fog lights would not shut off, had to pull fuse. Mechanic found left side multi function switch had an internal defect and the connector was melted at the switch. Both the switch and the connector had to be replaced. Concerned that this a potential fire hazard. *tr

NHTSA complaint #10645022
Aug 22, 2014electrical systemFire
Turned my Jeep on and the check engine light, sentry key light, fuel light came on and fuel gauge went to 0, Jeep ran for approx 30sec and shut off. Fuses were checked, nothing found out of place. Tried it again, same thing happened. Was towed to dealership to check and fix. Was informed that the main wiring harness near an o2 sensor was "fried" and that wires were fused… Read more

Turned my Jeep on and the check engine light, sentry key light, fuel light came on and fuel gauge went to 0, Jeep ran for approx 30sec and shut off. Fuses were checked, nothing found out of place. Tried it again, same thing happened. Was towed to dealership to check and fix. Was informed that the main wiring harness near an o2 sensor was "fried" and that wires were fused and melted together. Granted, my Jeep is 9 years old, but this is a design issue, not a wear and tear issue. Why would wiring be placed close enough to a heat source to where it's able to catch fire and fuse together? *tr

NHTSA complaint #10627410
Aug 2, 2014electrical system

Have had ongoing electrical issues beginning in august, 2010. Check engine lights that have been proven inaccurate. Have replaced fan motor resistor x 2, electrical control unit x1, fan blower x1. Wiring is melted (burnt) at locations indicating fuse system/ wiring harness is not functioning properly. *tr

NHTSA complaint #10618398
Jul 26, 2014electrical system

Key switch spindle went bad, had to replace key, then had to replace the complete key spindle and the wiring harness, it started to short out and cause a fire. Had to go to the dealership for repairs, cost $ 2087.00 dollars. *tr

NHTSA complaint #10616466
Nov 3, 2013electrical system, exterior lightingFire
Had been noticing a plastic burning smell for a couple months, never found a cause or anything not working properly. Driving home early one morning I noticed my headlights were not working, the brights worked and so did the fog lights, but no low beams. After looking on Jeep forums and noticing a lot of people were having the same problem I decided to take the cover off my… Read more

Had been noticing a plastic burning smell for a couple months, never found a cause or anything not working properly. Driving home early one morning I noticed my headlights were not working, the brights worked and so did the fog lights, but no low beams. After looking on Jeep forums and noticing a lot of people were having the same problem I decided to take the cover off my column and take a look. The wiring harness connected to my multifunction switch was burnt, proof of at least one small electrical fire, if not multiple small fires. I cannot be the only one with this problem, multiple posters on Jeep forums have reported similar events. *tr

NHTSA complaint #10550669
Feb 25, 2013electrical system
In trying to start my vehicle, a part inside of the ignition broke. I am told I cannot get the part that broke and I must purchase an entire steering column to replace this part in between the key and the electrical component that starts my vehicle. It is a small part, and I cannot see having the entire steering column to replace this small part. I am told by chrysler that… Read more

In trying to start my vehicle, a part inside of the ignition broke. I am told I cannot get the part that broke and I must purchase an entire steering column to replace this part in between the key and the electrical component that starts my vehicle. It is a small part, and I cannot see having the entire steering column to replace this small part. I am told by chrysler that the cost to repair this is about $800.00. I think this is entirely unreasonable and irresponsible on the part of the manufacturer. This part is used daily and should not fail after 60,000 miles of wear. My seven year / 70,000 mi warranty has just expired and I am appalled that such a large company cannot afford to fix or even stand behind their product. This is obviously a defective piece of equipment to have failed so prematurely. It is used every time you start this vehicle, and upon closer examination of this part, it seems that it is made of sub-standard material to be a part that must endure daily use.

NHTSA complaint #10501622
Apr 24, 2012electrical systemFire
2005 Jeep Wrangler. Consumer states within two weeks of purchase vehicle began experiencing electrical problems *tgw the consumer stated the heater/fan switch was replaced numerous times. On march 22, 2010, smoke began emitting from the vents into the interior of the vehicle. Within minutes, the vehicle was fully engulfed in flames and burned completely to the frame. … Read more

2005 Jeep Wrangler. Consumer states within two weeks of purchase vehicle began experiencing electrical problems *tgw the consumer stated the heater/fan switch was replaced numerous times. On march 22, 2010, smoke began emitting from the vents into the interior of the vehicle. Within minutes, the vehicle was fully engulfed in flames and burned completely to the frame. Chrysler determined there were no manufacturing defects despite the numerous problems the consumer encountered with the vehicle. *jb

NHTSA complaint #10456244
Jul 6, 2011electrical systemFire
I purchased my Jeep Wrangler rubicon sahara in july 2005. Over the years, the biggest problems I had were the infamous shaking of the car at speeds over about 55mph and the constant need to jump the car and buy new batteries. The latter problem seemed like something I could live with but over time it became worse and you could no longer rely on the car to start. Jeep has… Read more

I purchased my Jeep Wrangler rubicon sahara in july 2005. Over the years, the biggest problems I had were the infamous shaking of the car at speeds over about 55mph and the constant need to jump the car and buy new batteries. The latter problem seemed like something I could live with but over time it became worse and you could no longer rely on the car to start. Jeep has always been very cavalier about these problems, but they are real. My car now has only about 17,000 miles on it because of the reliability problem. In january 2011 there was an electrical explosion and smoke in the car. It was towed to lithia Jeep in santa fe nm (where I originally bought it). They couldn't really figure out the problem, but charged me for some rewiring and sent it back to me. Within days, the battery was dead again, so I bought a new battery. Within days, that battery was dead and the car was again towed to Jeep. This time, I filed a formal complaint with chrysler, who accepted the case.the dealer fiddled around with the car without success for a month, before chrysler agreed to accept most of the charges for a comprehensive rewiring of the car. The dealer also informed me at the time that it was unable to do the recall work on the car's transmission, because the bolts securing the transmission had been stripped at the factory. This seemed odd to me, that a dealer was telling me it couldn't do the recall work on a dangerous condition, so I just had to live with it. In march the de

NHTSA complaint #10410794
Sep 20, 2006electrical systemFire
Noticed a burning smell and thought it was one of four trucks ahead of me. Pulled off onto my exit and continued to notice the smell. Smoke began pouring from the dash. I had seen the service department the same morning and informed them my blower motor had been working intermittently. They verified the problem and ordered a new motor. Upon inspection of my vehicle I… Read more

Noticed a burning smell and thought it was one of four trucks ahead of me. Pulled off onto my exit and continued to notice the smell. Smoke began pouring from the dash. I had seen the service department the same morning and informed them my blower motor had been working intermittently. They verified the problem and ordered a new motor. Upon inspection of my vehicle I notice that the area around the blower motor is extremely hot. Blower motor has the following: label 1 valeo:kjlhd 929520g rev a -- pass 11-18-4 10:10:50 label 2 bosch made in mexico dpl 653 12v 9 000 025 075 19 904 929431h cw 49104 1. *nm

NHTSA complaint #10168749
← All 2005 Jeep Wrangler problems & recalls