Oct 22, 2026structure
The contact owns a 2008 Honda CR-V. The vehicle was recently taken to a dealer to be repaired under NHTSA campaign number: 23v228000 (structure). The contact stated that the dealer was required to perform a rigorous 7-point safety inspection to ensure the frame was structurally sound for the rear trailing arm reinforcement brace to function properly. However, the dealer… Read more
The contact owns a 2008 Honda CR-V. The vehicle was recently taken to a dealer to be repaired under NHTSA campaign number: 23v228000 (structure). The contact stated that the dealer was required to perform a rigorous 7-point safety inspection to ensure the frame was structurally sound for the rear trailing arm reinforcement brace to function properly. However, the dealer overlooked a critical rust hole on the frame by the trailing arm brace. The dealer improperly completed the recall repair despite the structural failure and informed the contact that the recall repair was successfully performed. The contact became aware of the issue after arriving to the residence. The contact believed that the issue posed an immediate safety risk. The vehicle was taken back to the dealer for re-evaluation; however, the dealer refused to provide further assistance. The manufacturer was notified of the structural failure. The failure mileage was 191,000.
NHTSA complaint #11773077
Oct 5, 2026suspension, structure
While driving on october 2, 2026, the driver-side rear trailing arm and subframe mounting structure detached from the frame due to severe corrosion. The vehicle was immediately taken to brandon Honda (tampa, fl) for inspection under safety recall 23v228000 / campaign 23-032. Brandon Honda documented on repair order #250035 that the "driver rear sub-frame looks to be completely… Read more
While driving on october 2, 2026, the driver-side rear trailing arm and subframe mounting structure detached from the frame due to severe corrosion. The vehicle was immediately taken to brandon Honda (tampa, fl) for inspection under safety recall 23v228000 / campaign 23-032. Brandon Honda documented on repair order #250035 that the "driver rear sub-frame looks to be completely detached." however, instead of submitting required inspection failure photos to Honda techline for corporate repurchase evaluation as mandated by service bulletin 23-032, the dealership issued a $4,222.77 customer-pay body shop estimate from nu finish collision center (estimate #046670) to replace the suspension crossmember, trailing arm, and frame rails out of pocket. The vehicle has a completely detached rear trailing arm/subframe, fails the safety recall inspection, and is grounded at the dealership as unsafe to drive. The dealership is refusing to follow official recall failure protocol and attempting to shift financial responsibility onto the consumer for a safety defect covered under federal recall mandates.
NHTSA complaint #11768926
Jun 26, 2026structure
The contact owns a 2008 Honda CR-V. The contact stated that while driving at an undisclosed speed, the vehicle felt as if it was driving over a bump in the road, causing the steering wheel to be unstable. Upon inspecting the vehicle, the contact became aware that the rear trailing arm was rusted. The contact referenced NHTSA campaign number: 23v228000 (structure); as a… Read more
The contact owns a 2008 Honda CR-V. The contact stated that while driving at an undisclosed speed, the vehicle felt as if it was driving over a bump in the road, causing the steering wheel to be unstable. Upon inspecting the vehicle, the contact became aware that the rear trailing arm was rusted. The contact referenced NHTSA campaign number: 23v228000 (structure); as a possible cause for the failure; however, the recall repair was marked as completed. The dealer determined that the recall repair was not performed. The dealer was notified of the failure, but the vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was 202,713.
NHTSA complaint #11746757
Dec 11, 2025structure
Hello, I have a recall for the corrosion on my Honda crv 2008, american Honda already has everything on file from the dealer ship I took to get it inspected and is been a whole month and american Honda hasn’t reached out to me. I have been asking american Honda if I could get a loaner car or rental as the service manager at the dealership has said he cannot provide a rental… Read more
Hello, I have a recall for the corrosion on my Honda crv 2008, american Honda already has everything on file from the dealer ship I took to get it inspected and is been a whole month and american Honda hasn’t reached out to me. I have been asking american Honda if I could get a loaner car or rental as the service manager at the dealership has said he cannot provide a rental until american Honda authorized since obviously some one has to pay for it. And I’m just reaching out if you guys could help me anyway to help me get this sorted out, dealership has already told me the car is un repairable at this point due to the bad corrosion and american Honda has acknowledged that and said someone from the median department or something like that was gonna reach out to me that was 2 weeks ago and I have reached out a week ago and they said someone would reach out and I have not received anything as I have told them, I really need a car since I recently had my baby and you know I need to come to work and go back home. Please if you guys can help me
NHTSA complaint #11704434
May 1, 2025structure
This is a complaint in reference to a current recall for the rear rust and corrosion issues on Honda crvs, part 573 safety recall report 23v-228. I brought my vehicle to matt burne Honda on january 7 2025 for this recall and they "inspected" and passed the vehicle, installed the brace, and said all was well as they handed me the keys. In early march I took the car in for its… Read more
This is a complaint in reference to a current recall for the rear rust and corrosion issues on Honda crvs, part 573 safety recall report 23v-228. I brought my vehicle to matt burne Honda on january 7 2025 for this recall and they "inspected" and passed the vehicle, installed the brace, and said all was well as they handed me the keys. In early march I took the car in for its state inspection and it failed due to all of the rust/corrosion/frame rot on the rear of this vehicle. When I called matt burne to find out why they installed the brace on this vehicle with all that rust, and why they never even bothered to mention the rust to me, they said that for the recall to pass all they needed to do was remove the bolt for the trailing arm and that all the rust didn't matter, and whether or not it could pass a state inspection didn't matter. This, put me and my family at risk. The rust and corrosion is severe. My family and I have been driving in it thinking it was all okay since the recall was completed. Yet they never thought to mention it. Isn't this recall in reference to rust and corrosion on the rear frame? Yes, I understand it involves the trailing arm, but wasn't there a punch test and a frame inspection that was supposed to be a part of this? How is it that the frame can rot away and practically disintegrate and yet that doesn't matter? After a month of trying to reach Honda, they finally told me I needed to take it to a Honda dealer because the 2 inspection centers I had
NHTSA complaint #11658299
Feb 13, 2025suspension, structure
The contact’s son owns a 2008 Honda CR-V. The contact stated that while his son was driving 45 MPH, the vehicle aggressively veered over to the right side of the road. The driver inspected the vehicle and noticed that the rear axle had detached from the frame. The driver was able to coast to the side of the road. The vehicle was towed to the dealer who was unable to fix the… Read more
The contact’s son owns a 2008 Honda CR-V. The contact stated that while his son was driving 45 MPH, the vehicle aggressively veered over to the right side of the road. The driver inspected the vehicle and noticed that the rear axle had detached from the frame. The driver was able to coast to the side of the road. The vehicle was towed to the dealer who was unable to fix the vehicle under NHTSA campaign number: 23v228000 (structure); because parts were not available, and there were additional damages that needed to be repaired. The manufacturer was made aware of the failure and was working with the dealer to have the vehicle inspected. The failure mileage was unknown. Parts distribution disconnect.
NHTSA complaint #11642485
Feb 10, 2025structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) and the vehicle was repaired under the recall; however, the contact was informed that the dealer had observed a 3x8 inch hole located 2 inches away from where the support brace was installed. The contact stated that despite the hole, the dealer determined that… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) and the vehicle was repaired under the recall; however, the contact was informed that the dealer had observed a 3x8 inch hole located 2 inches away from where the support brace was installed. The contact stated that despite the hole, the dealer determined that the vehicle was safe to drive, and the vehicle passed inspection. The contact believed that the recall repair failed to adequately address the safety concerns of the recall, potentially leaving the vehicle with a rear trailing arm that could still detached in the future. The manufacturer was made aware of the failure and a case was filed regarding a possible buyback; however, the request was denied due to the age of the vehicle. The failure mileage was 211,600.
NHTSA complaint #11641727
Jun 17, 2024structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The local dealer was contacted. The dealer informed the contact that there was an extreme amount of rust to the frame of the vehicle. The bolts failed to release due to the extreme rust. The… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The local dealer was contacted. The dealer informed the contact that there was an extreme amount of rust to the frame of the vehicle. The bolts failed to release due to the extreme rust. The vehicle was not able to be placed on the lift due to frame rust. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The approximate failure mileage was 133,267. Parts distribution disconnect.
NHTSA complaint #11594729
May 6, 2024structure
Two actuator for the doors were said to be replaced by the previous owner in 2015. However, all four of my actuators are not working. Sometimes, it unlocks by itself when driving and I have had issues at times when I am not able to unlock the door at all. This poses safety risk to not being able to get out at times from both inside and outside.
NHTSA complaint #11587225
Mar 26, 2024structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the recall repair could not be completed due to the extent of corrosion on the vehicle. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair as the recall notice was received over a year ago and the… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the recall repair could not be completed due to the extent of corrosion on the vehicle. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair as the recall notice was received over a year ago and the inspection was completed 8 months ago. Also, as per the recall notification, depending on the extent of any corrosion damage, Honda might offer to repurchase the vehicle. The dealer was contacted and confirmed that the recall repair could not be completed due to the extensive corrosion. The manufacturer was contacted, and the contact stated no offer was made, however a case was opened. Parts distribution disconnect.
NHTSA complaint #11579450
Jan 26, 2024structure
When I unlock the key fob and put hand break to park the driver side door makes a loud squeeky sound.
NHTSA complaint #11567923
Dec 5, 2023structure
The contact owns a 2008 Honda CR-V. The contact stated that upon taking the vehicle into an independent mechanic for service, the contact was made aware that the rear trailing arm had severe frame corrosion, potentially compromising the vehicle safety. The vehicle was taken to the dealer, who confirmed the diagnosis and advised the contact that the vehicle could not be… Read more
The contact owns a 2008 Honda CR-V. The contact stated that upon taking the vehicle into an independent mechanic for service, the contact was made aware that the rear trailing arm had severe frame corrosion, potentially compromising the vehicle safety. The vehicle was taken to the dealer, who confirmed the diagnosis and advised the contact that the vehicle could not be repaired. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA campaign number: 23v228000 (structure) however, the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 150,000.
NHTSA complaint #11558551
Nov 3, 2023suspension, structure
Evidence of corrosion on the rear trailing arms as described in the recent salt belt recall of 07-11 Honda crv’s. Petition to expand the monitoring and repair scope of this recall to include the appalachian regions of north carolina and tennessee as the use of road salt is also prevalent in these areas.
NHTSA complaint #11553438
Sep 26, 2023structureCrash
On october 9, 2022, I filed a complaint with NHTSA regarding this vehicle due to excessive and extreme rear frame corrosion. On may 6, 2023, my son was driving this vehicle and was involved in an incident while the vehicle was in motion. The rear subframe separated from the vehicle on the driver side. My son lost control of the vehicle. Fortunately, my son was able to avoid a… Read more
On october 9, 2022, I filed a complaint with NHTSA regarding this vehicle due to excessive and extreme rear frame corrosion. On may 6, 2023, my son was driving this vehicle and was involved in an incident while the vehicle was in motion. The rear subframe separated from the vehicle on the driver side. My son lost control of the vehicle. Fortunately, my son was able to avoid a direct collision with oncoming traffic. On may 15, 2023, the vehicle was towed to victory Honda in monroe, michigan. The vehicle was inspected, and we were assigned a case number (#13814983). We were promised a loaner vehicle (which has never been made available). As a result, my son had to resign his position at work because he lost his mode of transportation. I have called american Honda on a weekly basis requesting an update. I've been told our case is almost completed. We have been waiting for more than 4 months for the buyback as promised. We were told we would be getting $7,900 for the CR-V, plus out of pocket costs paid for a rental car on two occasions and payment for recent mechanical improvements. Honda USA has failed to resolve this manner in a reasonable and timely manner. 100+ days is not timely. We have lost income due to the loss of use of this vehicle. We have not been provided the loaner vehicle as promised. Please escalate our complaint. This is the second time this matter is being reported to the NHTSA. Please note, this is more serious now since my son was driving the vehicle when the
NHTSA complaint #11546541
Sep 21, 2023structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11545800
Aug 9, 2023structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) and the vehicle was taken to the dealer for the recall repair; however, the dealer informed the contact that they could not install a support brace on the vehicle because unknown bolts failed to loosen for the repair. The dealer had not provided any additional… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) and the vehicle was taken to the dealer for the recall repair; however, the dealer informed the contact that they could not install a support brace on the vehicle because unknown bolts failed to loosen for the repair. The dealer had not provided any additional information regarding the failure. The contact was informed that photos had been sent to the manufacturer and the dealer was awaiting a response. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and informed the contact that an assessment and follow up would be made. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11537409
Jul 13, 2023structure, latches/locks/linkages
The contact owns a 2008 Honda CR-V. The contact stated that the vehicle was taken to the dealer for the recall repair of NHTSA campaign number: 23v228000 (structure) and an unknown door latch recall; however, while driving after the vehicle was returned, the contact became that the doors were no longer closing securely, and the vehicle failed to respond immediately while… Read more
The contact owns a 2008 Honda CR-V. The contact stated that the vehicle was taken to the dealer for the recall repair of NHTSA campaign number: 23v228000 (structure) and an unknown door latch recall; however, while driving after the vehicle was returned, the contact became that the doors were no longer closing securely, and the vehicle failed to respond immediately while depressing the brake pedal. There was no warning light illuminated. Additionally, the contact stated that the dealer had stated in the recall repair work order that the recall repair of NHTSA campaign number: 23v228000 (structure) could not be completed on the vehicle due to severe frame corrosion and that the sub frame needed to be replaced; however, the dealer installed support braces on the vehicle and marked the recall as complete. The vehicle was taken to an independent mechanic, where it was diagnosed that the brake caliper had seized. The independent mechanic notified the contact that the vehicle was unsafe to drive. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 402,685.
NHTSA complaint #11532152
Jul 11, 2023structure
The rear frame of my crv has corroded and deteriorated. The rear trailing arm is at risk of falling off and could cause a loss of vehicle control, increasing the risk of a crash. The recall paperwork I received from american Honda motor co. Inc. States, “your Honda dealer will inspect the rear frame for corrosion. Depending on the extent of corrosion, the dealer may attach a… Read more
The rear frame of my crv has corroded and deteriorated. The rear trailing arm is at risk of falling off and could cause a loss of vehicle control, increasing the risk of a crash. The recall paperwork I received from american Honda motor co. Inc. States, “your Honda dealer will inspect the rear frame for corrosion. Depending on the extent of corrosion, the dealer may attach a support brace to the rear frame and/or repair the rear frame, for free. If the rear frame cannot be repaired, Honda may offer to repurchase the vehicle from you. If you paid out of pocket to have these specific recall repairs performed on your vehicle, you may be eligible for reimbursement.” I took my vehicle to Honda north for the repair. They attached the support brace, yet told me my vehicle is still unsafe to drive and refused to pass my vehicle for the required pa state inspection. I believe they need to move to the next step on the recall (repair of the rear frame) since the addition of the support brace did nothing to correct the safety issue on my vehicle. I took my vehicle to get two second opinions and both stated the vehicle is unsafe to drive due to the rear frame corrosion. I do not understand how Honda can put out a recall specific to the rear frame, then refuse to make the appropriate corrections so that the vehicle is safe. Why bother attaching the support brace if it does nothing to correct the reason for Honda’s recall? I filed a complaint with american Honda, but I have not hea
NHTSA complaint #11531678
Jun 28, 2023structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) and the vehicle was taken to the dealer for the recall repair. However, the dealer fractured the rear trailing arm bolts while inspecting the vehicle and informed the contact that they could not complete the recall repair due to corrosion. The dealer advised… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) and the vehicle was taken to the dealer for the recall repair. However, the dealer fractured the rear trailing arm bolts while inspecting the vehicle and informed the contact that they could not complete the recall repair due to corrosion. The dealer advised the contact that the manufacturer was notified of the issue, and the dealer was awaiting a decision from the manufacturer whether to buy back the vehicle. The contact stated that the vehicle was undrivable and he had not received assistance from the manufacturer or the dealer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and a case was opened. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11529415
Jun 27, 2023steering, structure
The contact owns a 2008 Honda CR-V. The contact stated that the vehicle was previously repaired under NHTSA campaign number: 23v228000 (structure). The contact stated that while driving at an undisclosed speed, the vehicle made an abnormal sound. The contact self-inspected the vehicle and noticed that the power steering fluid level was low. The contact filled the power… Read more
The contact owns a 2008 Honda CR-V. The contact stated that the vehicle was previously repaired under NHTSA campaign number: 23v228000 (structure). The contact stated that while driving at an undisclosed speed, the vehicle made an abnormal sound. The contact self-inspected the vehicle and noticed that the power steering fluid level was low. The contact filled the power steering fluid reservoir; however, two days later, the failure recurred. The vehicle was taken to the dealer, where the passenger’s side front ball joints were replaced, the power steering kit was installed, and the drive belt was replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 135,500.
NHTSA complaint #11529128
Jun 26, 2023structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) and requested to be removed from the recall distribution list. The local dealer was contacted. The manufacturer was not contacted.
NHTSA complaint #11528978
Jun 22, 2023structure, latches/locks/linkages
Door locks they lock and unlock by themselves and make a noise when locking. Also paint on car doors and back hood paling off car you see medal.
NHTSA complaint #11528335
Jun 14, 2023structure
The contact owns a 2008 Honda CR-V. The contact stated that while having an inspection performed on the vehicle, she was informed that the rear sub frame was corroded and had holes. The vehicle was taken to the local dealer where the vehicle was repaired under NHTSA campaign number: 23v228000 (structure). The contact stated that the rear support brace was added. The vehicle… Read more
The contact owns a 2008 Honda CR-V. The contact stated that while having an inspection performed on the vehicle, she was informed that the rear sub frame was corroded and had holes. The vehicle was taken to the local dealer where the vehicle was repaired under NHTSA campaign number: 23v228000 (structure). The contact stated that the rear support brace was added. The vehicle was repaired but the mechanic informed the contact that the vehicle was not drivable. The manufacturer was contacted but provided no additional assistance. The failure mileage was approximately 128,000.
NHTSA complaint #11526964
Jun 13, 2023structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11526809
Jun 6, 2023structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11525637
May 18, 2023structure
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The… Read more
The contact owns a 2008 Honda CR-V. The contact received notification of NHTSA campaign number: 23v228000 (structure) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11522717
May 18, 2023structure
The contact's son owned a 2008 Honda CR-V. The contact stated that while her son was driving at approximately 35 MPH, the rear axle detached from the vehicle. No warning lights were illuminated. A police report was filed. The vehicle was towed to a local dealer. The vehicle was then towed on two occasions to two separate independent mechanics, who related the failure to NHTSA… Read more
The contact's son owned a 2008 Honda CR-V. The contact stated that while her son was driving at approximately 35 MPH, the rear axle detached from the vehicle. No warning lights were illuminated. A police report was filed. The vehicle was towed to a local dealer. The vehicle was then towed on two occasions to two separate independent mechanics, who related the failure to NHTSA campaign number: 23v228000 (structure) and deemed the vehicle inoperable. The vehicle was not repaired and was towed to a salvage yard. The manufacturer was made aware of the failure. The approximate failure mileage was 130,000. The VIN was not available.
NHTSA complaint #11522644
Apr 21, 2023structure
The contact owns a 2008 Honda CR-V. The contact stated that while her son was driving at 35 MPH, the rear subframe detached. The vehicle was towed to the residence. The contact related the failure to NHTSA campaign number: 23v228000 (structure). The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure. The… Read more
The contact owns a 2008 Honda CR-V. The contact stated that while her son was driving at 35 MPH, the rear subframe detached. The vehicle was towed to the residence. The contact related the failure to NHTSA campaign number: 23v228000 (structure). The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 155,000.
NHTSA complaint #11518203
Dec 12, 2022structure
Door not latching properly NHTSA recall id: 12v338000 my doors on my 2008 problems with the CR-V door locks include: door not latching properly doors not unlocking doors locking and unlocking on their own was not made aware of the recall to fix this issue. I would like Honda to fix this issue for free at my delaership
NHTSA complaint #11497003
Oct 9, 2022structure
Honda is aware of an issue affecting many CR-V's. Honda has recently issued a recall of the 2007-2011 model-year CR-V's in canada for a rusting problem that could result in a rear suspension control arm separating from the vehicle. This recall applies to vehicles in all provinces from ontario east, which experience heavy road salt usage and humid operating environments.… Read more
Honda is aware of an issue affecting many CR-V's. Honda has recently issued a recall of the 2007-2011 model-year CR-V's in canada for a rusting problem that could result in a rear suspension control arm separating from the vehicle. This recall applies to vehicles in all provinces from ontario east, which experience heavy road salt usage and humid operating environments. Dealers were instructed to inspect the rear frame stiffeners and to apply corrosion protection. When a vehicle does not pass the inspection, Honda will offer to repurchase it. My son is 17 years old and is driving an affected CR-V. We live near detroit in michigan. I contacted Honda USA and lodged a complaint. I was given the following case #013293139 and instructed to set an appointment with a local Honda dealership for an inspection. Following the inspection, I was told and given a service invoice which stated, "subframe inspection for Honda case number 13293139 tech found rear of frame rusted through, tech advised starting with removing rear part of frame and welding in new metal. Vehicle not safe to operate in current condition. American Honda will not cover repair." this rust problem also affects other Honda vehicles and Honda is slowly issuing recalls. Recently, american Honda recalled 2006-2014 ridgelines for "rear frame corrosion." I would like Honda to repair my son's CR-V. This is not normal wear and tear. The corrosion problem continues to be focused on the rear driver side (subframe mounting to
NHTSA complaint #11488535
Apr 21, 2022structure
The contact owns a 2008 Honda CR-V. The contact stated while driving approximately 20-25 MPH, the rear passenger's side frame stiffeners detached and separated from the vehicle. The contact veered to the side of the road. The vehicle was towed to the contact's residence. Additionally, the contact stated that the frame stiffeners were severely rusted. The dealer and the… Read more
The contact owns a 2008 Honda CR-V. The contact stated while driving approximately 20-25 MPH, the rear passenger's side frame stiffeners detached and separated from the vehicle. The contact veered to the side of the road. The vehicle was towed to the contact's residence. Additionally, the contact stated that the frame stiffeners were severely rusted. The dealer and the manufacturer were not notified of the failure. The vehicle was not diagnosed or repaired. The failure mileage was approximately 262,000.
NHTSA complaint #11461618
Feb 28, 2022suspension, structure, wheels
This vehicle had a wheel separation while traveling at low speed. The right rear wheel separated from the car. The cause is excessive rust to the trailing arm and specifically to the subframe to which the trailing arm is attached. The car is available for inspection. I also have photographs that show the problem. The safety issue is clear. After separation the car… Read more
This vehicle had a wheel separation while traveling at low speed. The right rear wheel separated from the car. The cause is excessive rust to the trailing arm and specifically to the subframe to which the trailing arm is attached. The car is available for inspection. I also have photographs that show the problem. The safety issue is clear. After separation the car cannot be controlled if in motion. This particular vehicle has not been inspected. The wheel separation was reported by me to Honda in north america, to "chris" in "client relations." a case number was issued for my complaint, #00499145. An insurance claim was made, but the insurer denied the claim. My research shows that this model crv has been recalled in canada for this precise problem. In canada, Honda states that this model crv has "excessive" rust, leading to failure. Further, that the problem is not readily apparent on inspection, and in fact this car is inspected annually as part of north carolina licensure, and no inspection ever revealed the excessive rust threat. Here is the Honda press release: " january 23, 2019 Honda has voluntarily recalled approximately 83,953 2007-2011 CR-V vehicles in canada to address potential excessive corrosion to the rear frame stiffener(s). On affected vehicles, one or both rear frame stiffener(s) may become excessively corroded over time. Such excessive corrosion may be more prevalent where a vehicle is regularly operated in regions where road de-icing
NHTSA complaint #11454417
Jul 19, 2021structure
I had my car in the shop as I had an issue with my starter. The mechanic sent us photos as he found as serious problem with rust and corrosion around the rear axle. He thought it would be okay to drive home (not after that). He was wrong and the rear axle fell off. My dad was driving and as far as I know he is okay. I did research and it seems the vins starting with 5 were… Read more
I had my car in the shop as I had an issue with my starter. The mechanic sent us photos as he found as serious problem with rust and corrosion around the rear axle. He thought it would be okay to drive home (not after that). He was wrong and the rear axle fell off. My dad was driving and as far as I know he is okay. I did research and it seems the vins starting with 5 were made in ohio (I bought the car in ohio) and it the message boards are correct, were in the same batch as the canadian ones they recalled. They have not recalled these in the u.s. For the rear axle but they did in canada. Why? I drive my son every other weekend hours each way as his dad lives out of state. We travel I-65, I-70, and highways. We could have died! Honda needs to recall these immediately before someone dies. Please let me know if you need more photos. I will take more photos when the tow driver gets my car home.
NHTSA complaint #11425501
Jan 3, 2021structure
The entire vehicles paint is blotchy. As if acid was mixed in with a bad batch of paint.
NHTSA complaint #11386218
Aug 5, 2020structure
I brought my vehicle to a licensed garage to be inspected.they told me the rear frame stiffeners in my vehicle are corroded and will not pass new york state inspection. I was also warned it is extremely dangerous to continue to drive my car as the rear tire attaches to the rusted out spot on the frame. There is the potential for the rear tire assembly to detach while going… Read more
I brought my vehicle to a licensed garage to be inspected.they told me the rear frame stiffeners in my vehicle are corroded and will not pass new york state inspection. I was also warned it is extremely dangerous to continue to drive my car as the rear tire attaches to the rusted out spot on the frame. There is the potential for the rear tire assembly to detach while going down the road and cause loss of control. There is an open recall in canada for this exact problem for the years 2007 to 2011. There is currently no recall in the us.
NHTSA complaint #11343461
Dec 29, 2019suspension, structure
2008 CR-V subframe/rear control arm rusted so severely came apart while driving. Very fortunate there was not an accident, this caused sudden loss of control of vehicle. Had to be towed and is now inoperable and unable to be repaired. There is a recall in canada to address this condition, why not the united states? We contacted Honda customer service to inquire and no response… Read more
2008 CR-V subframe/rear control arm rusted so severely came apart while driving. Very fortunate there was not an accident, this caused sudden loss of control of vehicle. Had to be towed and is now inoperable and unable to be repaired. There is a recall in canada to address this condition, why not the united states? We contacted Honda customer service to inquire and no response from them. This is a very dangerous condition that gave no warning. The body is not rusted.
NHTSA complaint #11291820
Oct 10, 2019structure
Hello, the front right door of my car doesn't unlock at all and the back left door doesn't lock. Honda already has acknowledged the issue but this expired on 2015. Because the front door doesn't unlock it's a safety issue and the cost to fix is very expensive as the door needs to be deassembled. There cost to open the door and fix it is almost 500 dollars. I have called Honda… Read more
Hello, the front right door of my car doesn't unlock at all and the back left door doesn't lock. Honda already has acknowledged the issue but this expired on 2015. Because the front door doesn't unlock it's a safety issue and the cost to fix is very expensive as the door needs to be deassembled. There cost to open the door and fix it is almost 500 dollars. I have called Honda but they are saying the product warranty expired on 2015.
NHTSA complaint #11267660
Oct 10, 2019structure, unknown or other
The sunroof has become unattached and also I wash and wax my car I see oxidation in the paint
NHTSA complaint #11267583
Mar 18, 2019structure, latches/locks/linkages
Tl* the contact owns a 2008 Honda CR-V. The contact stated that the front driver and passenger doors did not lock. The contact also stated that the doors made an abnormal winding sound as if something was pulling the doors. An unknown warning indicator illuminated. The vehicle was taken to mcconnell Honda (2840 eastern blvd, montgomery, al 36116, (334) 271-2500) where the… Read more
Tl* the contact owns a 2008 Honda CR-V. The contact stated that the front driver and passenger doors did not lock. The contact also stated that the doors made an abnormal winding sound as if something was pulling the doors. An unknown warning indicator illuminated. The vehicle was taken to mcconnell Honda (2840 eastern blvd, montgomery, al 36116, (334) 271-2500) where the passenger door was repaired; however, the failure recurred. The front driver's door was not repaired because the mechanic stated that there was no recall. The manufacturer was not made aware of the failure. The failure mileage was 21,000.
NHTSA complaint #11189693
Nov 5, 2018electrical system, structure
Tl* the contact owns a 2008 Honda CR-V. While the vehicle was stationary, the door actuator failed and a strange noise was heard when the front driver's side door was opened. The contact also heard a buzzing noise coming from the front driver's side door when it was locked with the key fob. An independent mechanic and thelen Honda (1020 north euclid avenue, bay city, michigan… Read more
Tl* the contact owns a 2008 Honda CR-V. While the vehicle was stationary, the door actuator failed and a strange noise was heard when the front driver's side door was opened. The contact also heard a buzzing noise coming from the front driver's side door when it was locked with the key fob. An independent mechanic and thelen Honda (1020 north euclid avenue, bay city, michigan 48706, (989) 671-1150) were made aware of the failure. The dealer indicated that the vehicle was repaired per an unknown recall in 2015. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 158,000.
NHTSA complaint #11145381