The vehicle engine has failed with 5,525 miles and it will require a full engine replacement.
2026 GMC Yukon engine problems
39 owners reported engine & cooling problems — 76% of all 51 complaints about the 2026 GMC Yukon.
Engine & cooling complaints by GMC Yukon year
What owners report
My 2026 GMC Yukon denali ultimate with the 6.2l v8 had a major engine failure on november 2, 2026, while driving with only 3,668 miles on it. I bought it brand new in july. The dealership told me it was likely a rod or rod bearing failure and found metal in the oil. The entire engine has to be replaced. This is a serious safety concern, especially if the engine fails while… Read more
My 2026 GMC Yukon denali ultimate with the 6.2l v8 had a major engine failure on november 2, 2026, while driving with only 3,668 miles on it. I bought it brand new in july. The dealership told me it was likely a rod or rod bearing failure and found metal in the oil. The entire engine has to be replaced. This is a serious safety concern, especially if the engine fails while driving at highway speeds. A brand-new vehicle should not have a catastrophic engine failure with less than 4,000 miles. I’m concerned other 2026 yukons with the 6.2l engine could have the same issue.
Car with $13000 miles had sudden engine failure. Have heard numerous other new yukons have had this issue.
Has 3600 miles and engine suddenly lost power and had back knocking/squealing noise and check engine light started flashing.
Engine failure. While driving on the highway at a speed of approximately 70 MPH the engine made a noise and the vehicle lost power. The safety factor is that I was on the highway with trucks and busses in which I had to coast the vehicle to the shoulder of the road and call for police assistance. No warning lamps. Vehicle was towed and inspected by the dealer in which I… Read more
Engine failure. While driving on the highway at a speed of approximately 70 MPH the engine made a noise and the vehicle lost power. The safety factor is that I was on the highway with trucks and busses in which I had to coast the vehicle to the shoulder of the road and call for police assistance. No warning lamps. Vehicle was towed and inspected by the dealer in which I was informed that the engine bearings had locked up. The vehicle needed a new engine.
My 2026 GMC Yukon denali ultimate has had the vadar chrome peel in the first 7000 miles. After that a wiring pinch made the 4 wheel drive unusable during the winter months that I needed it to get into my driveway during summer months the infotainment center completely failed to a black screen and since does not function having the dealership tell me that it will need to be… Read more
My 2026 GMC Yukon denali ultimate has had the vadar chrome peel in the first 7000 miles. After that a wiring pinch made the 4 wheel drive unusable during the winter months that I needed it to get into my driveway during summer months the infotainment center completely failed to a black screen and since does not function having the dealership tell me that it will need to be replaced. The 6.2 motor started ticking at 25000 miles, I took it to the dealership yesterday 10/14, the dealership is keeping the vehicle for an estimated 6 weeks to tear the motor apart. The motor is making the noise where it is reported to shut down at high speeds had I not got it in when I did. The vehicle has had no warning to indicate problems.
Was operating Yukon on st route 5 doing 55mph when the yukons engine blew up and the vehicle shut down on me in the middle of the road.
While traveling on a state route in pennsylvania the engine unexpectedly locked up. This was confirmed by the dealer once it was towed to their lot and they were able to inspect it. To date, a replacement engine has not been able to be located yet, its been four weeks and no updates have been received.
This engine failed while I was driving. You need to speed up the process and make GM know that their 6.2 engines are failing still to this day . People can get in accidents due to this happening. GM needs to be held accountable for their mistakes. I was lucky my vehicle engine failed near my home and not on the interstate. Please get to the bottom of this . There is no reason that these engines are failing in 2026.
Engine failed . Stalled in the middle of the road . Engine ran bad . Shaking knocking and trebling. No engine lights on .
On 7/25/26 (a saturday), we started to hear a noise in my vehicle and shortly thereafter, were sent a service alert through the GMC app and the check engine light came on. We immediately parked the vehicle and took it to the dealership when they opened on 7/27/2026 (monday). Later that day, we were informed that my Yukon denali, with 9,226 miles on it, has metal fragments in… Read more
On 7/25/26 (a saturday), we started to hear a noise in my vehicle and shortly thereafter, were sent a service alert through the GMC app and the check engine light came on. We immediately parked the vehicle and took it to the dealership when they opened on 7/27/2026 (monday). Later that day, we were informed that my Yukon denali, with 9,226 miles on it, has metal fragments in the oil caused by some sort of failure in the bottom half of the engine and the engine needs to be replaced. The engine was replaced and I picked up my car on 8/17/2026. The check engine light came on again on 8/20/2026 and after three trips to the dealership, my catalytic converter was replaced. Since purchasing my car on december 4, 2025, I have taken it back to the dealership 5 times for non-routine services (and once for a routine oil change). Since purchasing a brand new 2026 GMC denali (a car that cost over $100,000) less than 10 months ago, I have been without my car for 33 days for manufacturing related issues that are all under warranty. I still don't think the engine issues are fixed (or I have another bad engine). My vehicle sounds metallic at start up (different than it sounded when I purchased the vehicle and different than other 2024-2026 GMC yukons with the same engine) and idles rougher than it used to. I am nervous driving my car on road trips now, which is one of the primary reasons we purchased the vehicle. I did my research before purchasing this vehicle and based on information f
Engine stopped. Would not restart. I had it towed to dealership. They told me the engine is blown. There is only 7700 miles on the truck.
Engine failed on this 2026 GMC Yukon denali.. It had only 18000 miles on it, it failed in middle of hwy in indiana. Got it towed to dealership.. They haven’t touched it since last 2 days.
While traveling at highway speeds of approximately 82 MPH in a 2026 GMC Yukon denali (6.2l v8 l87 engine), the engine experienced a sudden, catastrophic internal failure and completely seized without warning. This resulted in an immediate, total loss of motive power, power steering assist, and power braking assist while surrounded by high-speed traffic. The sudden deceleration… Read more
While traveling at highway speeds of approximately 82 MPH in a 2026 GMC Yukon denali (6.2l v8 l87 engine), the engine experienced a sudden, catastrophic internal failure and completely seized without warning. This resulted in an immediate, total loss of motive power, power steering assist, and power braking assist while surrounded by high-speed traffic. The sudden deceleration and lack of vehicle control created an extreme, life-threatening safety hazard, forcing an emergency maneuver across multiple lanes to reach the shoulder. Stranded on shoulder at night(pitch black) with lots of 18 wheelers passing.
-transmission started to slip when shifting above 2000rpms -engine light came on and took to dealership -error code confirmed for valve body, valve #3 failure -new valve body installed after order but also failed as I left the dealership -new valve body currently on order
The engine issue was caused by a misfire in cylinder #5, which resulted in white smoke coming from the vehicle’s exhaust. While driving on the highway, the vehicle lost power and would not accelerate properly, creating a serious safety hazard due to the inability to maintain speed and safely respond to traffic conditions.
The engine issue was caused by a misfire in cylinder #5, which resulted in white smoke coming from the vehicle’s exhaust. While driving on the highway, the vehicle lost power and would not accelerate properly, creating a serious safety hazard due to the inability to maintain speed and safely respond to traffic conditions.
The engine issue was caused by a misfire in cylinder #5, which resulted in white smoke coming from the vehicle’s exhaust. While driving on the highway, the vehicle lost power and would not accelerate properly, creating a serious safety hazard due to the inability to maintain speed and safely respond to traffic conditions.
The engine failed at 5383 miles while driving on remote highway in nebraska.
Driving down highway the engine made a squeeling noise. The engine shuttered and kept making noise then said to reduce speed. Then quit running all together.
The contact owns a 2026 GMC Yukon. The contact stated that while driving approximately 15-20 MPH and approaching a stop in nebraska, there was an abnormal sound coming from the vehicle. The vehicle was shaking and vibrating abnormally. The contact called the local dealer, and an appointment was scheduled. The failures persisted while waiting for the appointment. While driving… Read more
The contact owns a 2026 GMC Yukon. The contact stated that while driving approximately 15-20 MPH and approaching a stop in nebraska, there was an abnormal sound coming from the vehicle. The vehicle was shaking and vibrating abnormally. The contact called the local dealer, and an appointment was scheduled. The failures persisted while waiting for the appointment. While driving at an undisclosed speed, the vehicle lost motive power and stalled. The driver alerted onstar about the failure. The vehicle failed to restart. The vehicle was towed to the local dealer, where it was diagnosed with complete engine failure. The contact was informed that the engine needed to be replaced. The vehicle was repaired; however, the contact no longer wanted the vehicle. The manufacturer was contacted and opened a case and escalated the concerns. The failure mileage was approximately 4,700.
While we were visiting canada, our GMC Yukon had fewer than 5,000 miles when its engine seized on the highway. The vehicle was taken to a GMC dealership in canada. The dealer advised that the engine needed to be replaced, and it has now been replaced. We need to back to canada to pick up the vehicle.
While traveling on [xxx] from houston back to san antonio, my truck engine just blew up without any warning whatsoever. We purchased the truck with 3 miles on it, and we have only put 5,000 miles on it. New cars that cost early $100k shouldn’t be having engine failures like this. I’m lost for words now! Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
My Yukon denali ultimate had only 3,788 miles on it and on 7/27 while merging onto a highway my vehicle made a sound like it was trying to shift into gear but couldn't and then while I'm pressing the accelerator pedal it's slowing down. There were tractor trailer and vehicles speeding up behind me but I couldn't speed up and I was able to pull over on the shoulder luckily and… Read more
My Yukon denali ultimate had only 3,788 miles on it and on 7/27 while merging onto a highway my vehicle made a sound like it was trying to shift into gear but couldn't and then while I'm pressing the accelerator pedal it's slowing down. There were tractor trailer and vehicles speeding up behind me but I couldn't speed up and I was able to pull over on the shoulder luckily and I'm thankful it did not cause an accident. My Yukon would not start no matter what I tried and I ended calling a tow truck and had it towed to my local GMC delearship where I was informed that the engine had seized and they would order a new replacement engine. My Yukon is still sitting at the dealership waiting for the repair.
GMC should be haulted from selling trucks with the 6.2l engine. My brand new 2026 GMC Yukon denali engine imploded on the interstate going 75mph that nearly killed my entire family. No warning, just out of no where died on the highway, with 4k miles on it. This is sadly going to get someone critically injured and when is enough going to be enough? GMC has some explaining to… Read more
GMC should be haulted from selling trucks with the 6.2l engine. My brand new 2026 GMC Yukon denali engine imploded on the interstate going 75mph that nearly killed my entire family. No warning, just out of no where died on the highway, with 4k miles on it. This is sadly going to get someone critically injured and when is enough going to be enough? GMC has some explaining to do, when they charge $85k-$100k for trucks that blow up as soon as you buy them.
GMC should be haulted from selling trucks with the 6.2l engine. My brand new 2026 GMC Yukon denali engine imploded on the interstate going 75mph that nearly killed my entire family. No warning, just out of no where died on the highway, with 4k miles on it. This is sadly going to get someone critically injured and when is enough going to be enough? GMC has some explaining to… Read more
GMC should be haulted from selling trucks with the 6.2l engine. My brand new 2026 GMC Yukon denali engine imploded on the interstate going 75mph that nearly killed my entire family. No warning, just out of no where died on the highway, with 4k miles on it. This is sadly going to get someone critically injured and when is enough going to be enough? GMC has some explaining to do, when they charge $85k-$100k for trucks that blow up as soon as you buy them.
The contact owns a 2026 GMC Yukon. The contact stated that while driving 55 MPH and depressing the accelerator pedal, the vehicle failed to respond as intended. The contact pulled over to the side of the road, turned off and restarted the vehicle; however, the failure persisted. A dealer was contacted. The vehicle was towed to the dealer to be diagnosed, and the contact was… Read more
The contact owns a 2026 GMC Yukon. The contact stated that while driving 55 MPH and depressing the accelerator pedal, the vehicle failed to respond as intended. The contact pulled over to the side of the road, turned off and restarted the vehicle; however, the failure persisted. A dealer was contacted. The vehicle was towed to the dealer to be diagnosed, and the contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that there was a wait for the replacement engine. The approximate failure mileage was 3,788.
On july 30th 2026, I was driving on the highway at about 75 miles per hour and the engine shut down. We were fortunate that we could pull over to the side of the highway. We had the truck towed to oxendale GMC. Today 8/4/26 I was informed that in fact the engine needs to be replace. No warnings no symptoms, the truck just shut down while driving.
Engine failed at 12, 430 miles. Dealer said it required a new engine. This happened on 06/06/2026 and I am still without my very expensive vehicle. There were no wanring lamps or other engine failure notificatioins before this occurred.
So the ultimate failure is from a catastrophically failed crankshaft journal thrust bearing. Which could be caused from one of two things: 1) the crankshaft thrust bearings they are putting in these motors are made with inferior materials, probably cheap chinese crap or 2) the crankshaft end play tolerance was never set properly, giving the crankshaft the ability to move… Read more
So the ultimate failure is from a catastrophically failed crankshaft journal thrust bearing. Which could be caused from one of two things: 1) the crankshaft thrust bearings they are putting in these motors are made with inferior materials, probably cheap chinese crap or 2) the crankshaft end play tolerance was never set properly, giving the crankshaft the ability to move forward and backward in the engine more than it was designed to. Which will over time beat up on the thrust bearing until it fails. In either case it would result in the same progressive issue showing itself. It will start as a squeak here and there. Which, as the soft thrust bearing material is unable to hold the proper oil film thickness for lubrication, will spiral into more and more heat being sent into the adjacent components, plus the buildup of metal particles being sent through the entire engine oiling system. Which will then start killing connecting rod and crankshaft bearings one by one. If the engine survived to this point, it’s now a ticking time bomb. It is either going to just seize up and not run anymore or the exciting route would be a connecting rod breaks and makes a window sized hole in the side of the engine block.
My engine with less than 5,000 miles died (engine was blown). While driving on highway engine died and wheels locked and almost caused a major accident. I had to get a tow and bill cost me 700.00. GMC is giving me the run around. Dealer stated that engine will need to be replaced. GMC is doing nothing to assist me, I have a car note with no truck GMC is the biggest scam.
The contact owns a 2026 GMC Yukon. The contact stated that while driving at 65 MPH the engine seized. All the warning lights illuminated after the failure. The vehicle was towed to the local dealer, where it was diagnosed that an engine replacement was needed. The vehicle was not repaired due to the part being backordered. The manufacturer was not contacted. The failure mileage was approximately 10,000.
The vehicle experienced repeated failures involving the electronic stability control (ESC), traction control system, and check engine system. Warning indicators for the ESC, traction control, and check engine illuminated while operating the vehicle. The issue has occurred on two separate occasions. The first incident occurred on may 4, 2026. The vehicle was taken to the… Read more
The vehicle experienced repeated failures involving the electronic stability control (ESC), traction control system, and check engine system. Warning indicators for the ESC, traction control, and check engine illuminated while operating the vehicle. The issue has occurred on two separate occasions. The first incident occurred on may 4, 2026. The vehicle was taken to the dealership for inspection and repair, and the dealership advised that the issue had been corrected. However, the same problem reoccurred on may 7, 2026. The vehicle has been inspected by the dealership service department, and the malfunction was confirmed. The affected components and vehicle are available for inspection upon request. The failure created a significant safety concern because the ESC and traction control systems are critical safety features designed to assist with vehicle stability, traction, and driver control, particularly during emergency maneuvers or adverse road conditions. The warning indicators raised concerns that the vehicle could unexpectedly lose stability assistance, traction management, or engine performance while driving. This placed the driver and others at risk because the vehicle’s ability to respond safely during normal or emergency driving conditions could have been compromised. The repeated recurrence of the issue, even after dealership repair attempts, raises concern regarding the reliability and effectiveness of the corrective action performed.
Nothing has happened yet. However, after only 308 miles… my 2026 denali is knocking and ticking very loud. Why? How is this possible? We’ve only had it 2 weeks! I have only driven it 5-6 times in the past 14-15 days, too worried that this might happen. But I was reassured by the dealership it wouldn’t. But here I am now. I am so disappointed. Being a disabled vet I thought we… Read more
Nothing has happened yet. However, after only 308 miles… my 2026 denali is knocking and ticking very loud. Why? How is this possible? We’ve only had it 2 weeks! I have only driven it 5-6 times in the past 14-15 days, too worried that this might happen. But I was reassured by the dealership it wouldn’t. But here I am now. I am so disappointed. Being a disabled vet I thought we could have something that we both liked. Now I am upset because I feel betrayed and lied to. I did a video but it’s too large to upload so I can’t get it under 10mb.
Engine starting clicking during highway drive then engine failed mid-drive and engine was trying to restart on its own mid drive. Vehicle totally stalled out in the street, with numerous attempts the engine did not start. Total mileage on car was 2,900.
The engine started a soft, cyclic tapping sound intermittently on 2/28/26 while I was out of town on a trip. No alerts showed on the GM systems app. On 3/1, while driving home from the trip, the car started hard braking at cruising speed and the engine died and would not restart. I had the car towed to the closest GM dealership and have been told the engine locked up. I just… Read more
The engine started a soft, cyclic tapping sound intermittently on 2/28/26 while I was out of town on a trip. No alerts showed on the GM systems app. On 3/1, while driving home from the trip, the car started hard braking at cruising speed and the engine died and would not restart. I had the car towed to the closest GM dealership and have been told the engine locked up. I just rolled 6000 miles and showed 18% oil life from the original engine oil it came with from the factory. I had been watching the engine problems for years now and waiting for them to be resolved before buying a new GM; only to be lied to that the issue was resolved. Now they're going to install yet another defective engine.
2026 Yukon elevation with 3,957miles. I was driving down the road and pulled into the turn lane at an intersection. Vehicle cut off with the auto start/stop function and would not start back up. I continued and tried to restart the vehicle but would not start; I was blocking the lane with cars continuously going around me. Vehicle stated service transmission on the display- I… Read more
2026 Yukon elevation with 3,957miles. I was driving down the road and pulled into the turn lane at an intersection. Vehicle cut off with the auto start/stop function and would not start back up. I continued and tried to restart the vehicle but would not start; I was blocking the lane with cars continuously going around me. Vehicle stated service transmission on the display- I was unable to put it into neutral to push it out of traffic; you are only allowed to put it into neutral when crank and couldnt get the accessory mode to come on without the vehicle trying to start. I called the local police department and they sent an officer to direct traffic until a tow truck showed up. Both observed the vehicle not starting. There were no symptoms prior to the vehicle cutting off, only once auto start/stop initiated did the vehicle not restart. Vehicle will be sent back to the dealership tomorrow to resolve this issue. I have dash cam footage of the incident and photos of the display on the screen.
Engine failure while driving 75 miles per hour in highway in brand new Yukon denali. 3,000 miles and got a “decreased acceleration” warning. Then couldn’t accelerate and loud knocking noise from the engine, likely a lifter issue. I will have to get a new engine according to GMC. Unbelievable. Recall was for 2021-2024, but my 2026 is havin the same issue.
The contact owns a 2026 GMC Yukon denali. The contact stated that while driving approximately 55 MPH, the vehicle stalled and failed to return to normal operation. The message "shifting to neutral" was displayed on the instrument panel. The vehicle was towed to the dealer, where it was diagnosed, and determined that the engine needed to be replaced. The vehicle was not… Read more
The contact owns a 2026 GMC Yukon denali. The contact stated that while driving approximately 55 MPH, the vehicle stalled and failed to return to normal operation. The message "shifting to neutral" was displayed on the instrument panel. The vehicle was towed to the dealer, where it was diagnosed, and determined that the engine needed to be replaced. The vehicle was not repaired. The contact researched and became aware of an unknown recall however, the VIN was not under recall. The manufacturer was notified of the failure and referred the contact to the NHTSA hotline to report the failure. The failure mileage was approximately 3,303.