CarProblemsDB

2004 GMC Sierra 2500 HD brakes problems

37 owners reported brakes problems — 40% of all 93 complaints about the 2004 GMC Sierra 2500 HD.

Brakes complaints by GMC Sierra 2500 HD year

200523
200437
200356
200263
200153

What owners report

Jan 4, 2020steering, service brakes

During cold mornings (wisconsin) I start my truck and I have no power steering and soft brakes. It is my understanding that the power steering runs the brake boost. Also, it is my understanding that there is a service bulletin that says that the power steering fluid should be replaced with low/cold temp fluid. My concern is what happens if I lose power steering and brakes while I am driving.

NHTSA complaint #11297098
Mar 29, 2018service brakes

Pulling out of a parking lot, lost brakes. Steel brake lines by fuel tank, let go causing truck to loose brakes

NHTSA complaint #11082095
Feb 10, 2017electrical system, service brakes, engine
My vehicle had brake lines replace two times with less than 65,000 miles because breaks stop working. Fuel line replaced under 55,000 miles because it made check engine light come on speedometer erratic,oil pressure gauge high and low,fuel gauge erratic under 65,000 miles. Loud noise from engine service technician reported the exhaust manifold bolts has broken to call a… Read more

My vehicle had brake lines replace two times with less than 65,000 miles because breaks stop working. Fuel line replaced under 55,000 miles because it made check engine light come on speedometer erratic,oil pressure gauge high and low,fuel gauge erratic under 65,000 miles. Loud noise from engine service technician reported the exhaust manifold bolts has broken to call a white smoke from the motor. Everything happened with consider to be low mileage in talking to GM they don't care because enough report has not been made.

NHTSA complaint #10953952
Mar 18, 2016service brakes

Tl* the contact owns a 2004 GMC Sierra 2500 HD. While driving 10 MPH, the brakes failed without warning. It was diagnosed that all the brake lines needed to be replaced. The manufacturer was made aware of the failure. The approximate failure mileage was 176,395.

NHTSA complaint #10850446
Feb 9, 2015service brakes, hydraulic

The complaint is that the brake lines failed and are made of very poor material. The brake line failed on my way to work one day on march 10,2015.

NHTSA complaint #10733150
Feb 1, 2015service brakes
On 2/1/2015, at approximately 11:30 am, I was stopping at my brothers mailbox to get his mail while he was on vacation. When I went to stop at his mailbox, the brake pedal on my truck went to the floor with no resistance on the pedal. I pumped the brakes several times, put the truck in neutral and it came to a gradual stop over an extended braking distance of 20 to 30 feet… Read more

On 2/1/2015, at approximately 11:30 am, I was stopping at my brothers mailbox to get his mail while he was on vacation. When I went to stop at his mailbox, the brake pedal on my truck went to the floor with no resistance on the pedal. I pumped the brakes several times, put the truck in neutral and it came to a gradual stop over an extended braking distance of 20 to 30 feet (which is slightly uphill). There were no lights lit on the dash and the master cylinder was between the maximum and minimum levels on the reservoir, when I examined it after the occurrence. We live on a dirt road without much traffic, so I placed the truck in low range 4wd and drove it the 1/2 mile home. Upon returning home the top brake line which runs along the frame from the anti lock brake block back towards the drivers side rear of the truck had ruptured. The brake fluid in the master never went below the minimum level, so I attempted to refill it to see if I could get any brake pedal pressure back. The pedal went to the floor still after multiple tries with a full master cylinder. The brake line had ruptured where it is attached at a green plastic factory hanger. The brake line was corroded/rusted where it had failed. If I would not have stopped at my brothers mailbox, it is 1 mile down hill on an approximate 12 degree grade to the main road. The intersection at the bottom of the road is a 90 degree, t intersection in a creek bottom, where I am supposed to stop prior to entering the main road. We h

NHTSA complaint #10680368
Jan 9, 2015power train, service brakes

I was leaving a parking lot, and as I hit my brakes, there were no brakes. I limped home, using the e-brake and transmission to keep the truck under control. Upon inspection I found the front brake line rusted and leaking. *tr

NHTSA complaint #10671448
Sep 23, 2014service brakes
On 9-19-2014 the truck was stopped at a red light and started to inch forward. Slight pressure on the brake pedal stopped the movement. The event was so quick and slight I thought nothing about it. I turned on the freeway and drove 30 or 40 miles before touching the brake pedal again. When I did it went almost to the floor without slowing the truck speed any appreciable… Read more

On 9-19-2014 the truck was stopped at a red light and started to inch forward. Slight pressure on the brake pedal stopped the movement. The event was so quick and slight I thought nothing about it. I turned on the freeway and drove 30 or 40 miles before touching the brake pedal again. When I did it went almost to the floor without slowing the truck speed any appreciable amount. At that point I knew I had a serious problem. I geared the truck down and was able to avoid being involved in an accident. If I had needed to come to a full and fast stop it could easily have been a disaster. An internet search revealed GM has had this problem for some time without notice to truck owners that it exists. An inspection of the brake lines was done and indicated a failure in the brake line system due to rust. The fuel lines showed the same kind of deterioration. Pictures can be provided to verify the lack of advanced rust conditions to the underneath of the truck other than the brake line system, the fuel line system, and the drive shaft. The truck was purchased new in south carolina and has been driven there 90% on the total mileage on it. *tr

NHTSA complaint #10638398
Sep 22, 2014service brakes
This seldom used, well maintained, garaged truck, blew out the brake lines on left side on the frame, under the door, resulting in total brake failure. I had to use the parking brake to stop the vehicle. I was on my way to pick up a #9000 boat. If I had that boat behind the truck, it could have killed me, or others on the road. Brake lines are not a normal service part.… Read more

This seldom used, well maintained, garaged truck, blew out the brake lines on left side on the frame, under the door, resulting in total brake failure. I had to use the parking brake to stop the vehicle. I was on my way to pick up a #9000 boat. If I had that boat behind the truck, it could have killed me, or others on the road. Brake lines are not a normal service part. Replacing all the brake lines is costing me 1300, at a minimum. My neighbor next door has a similar 2004 GMC sierra, with about the same mileage, only his is a 1/2 ton, where mine is 3/4 ton. His truck had the same failure the week before, in the exact same location on the lines. Do a simple search looking for brake failures on these vehicles, and you find that its well documented. This should be a recall before people are killed. There is no way that I should be looking at brake line failure on a 10 year old garaged truck that has a tow capacity of over 10,000 #'s. How should someone detect the integrity of the brake lines to determine when the should be replaced? *tr

NHTSA complaint #10638025
Sep 12, 2014service brakes

Brake lines rusted and leaking. *tr

NHTSA complaint #10632803
Apr 19, 2014structure, service brakes

All the fluid lines corroded to the point where the vehicle was dangerous to drive with only 35000 original miles on it. *tr

NHTSA complaint #10583638
Mar 4, 2014service brakes
Brake pedal went to the floor. Almost impossible to drive like that. Takes over 100x longer to stop a 3/4 ton truck. I found that the brake lines rusted out. I also found several hundred reports of the same things on GM truck online. I also heard you were investigating this issue already. I wanted to make sure I am counted as one of the effected people. I also read where GM… Read more

Brake pedal went to the floor. Almost impossible to drive like that. Takes over 100x longer to stop a 3/4 ton truck. I found that the brake lines rusted out. I also found several hundred reports of the same things on GM truck online. I also heard you were investigating this issue already. I wanted to make sure I am counted as one of the effected people. I also read where GM does not consider this a safety issue. I disagree. The line from the master cylinder to the ABS unit blew so I had zero brake pressure and pedal. I think this should be recalled as it is a huge safety issue. I have already spent over $1000 and a week trying to fix this and replace all the rusted line. I still do not have the truck back on the road. Thanks *tr

NHTSA complaint #10567069
Sep 13, 2013service brakes
Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving 40 MPH, he applied the brakes but the vehicle did not respond. He continued applying pressure until the pedal touched the floorboard and finally, the vehicle came to a stop. The vehicle was taken to a dealer for diagnosis and the contact was informed that the steel brake lines exhibited… Read more

Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving 40 MPH, he applied the brakes but the vehicle did not respond. He continued applying pressure until the pedal touched the floorboard and finally, the vehicle came to a stop. The vehicle was taken to a dealer for diagnosis and the contact was informed that the steel brake lines exhibited massive corrosion and were leaking. The vehicle was taken to a different dealer where the repair was completed. The manufacturer was notified of the failure. The failure and current mileage was 80,000.

NHTSA complaint #10543468
Sep 5, 2013service brakes
While traveling on the pa turnpike at approx. 60 MPH, traffic suddenly slowed in front of me. I was pulling our 30 fifth wheel camper at the time. I applied the brake hard had a split second of braking action and then the brake pedal went to the floor. I was able to use the manual trailer brake control to slow the truck some, swerved into the left lane missing the car in front… Read more

While traveling on the pa turnpike at approx. 60 MPH, traffic suddenly slowed in front of me. I was pulling our 30 fifth wheel camper at the time. I applied the brake hard had a split second of braking action and then the brake pedal went to the floor. I was able to use the manual trailer brake control to slow the truck some, swerved into the left lane missing the car in front of me by inches and the car to the left of me swerved into the far left lane to avoid hitting me. (three lane highway) I managed to drive the truck to a rest area about a mile down the road using both the trailer brakes and the truck emergency brakes. The cause of the brake failure was that the brake line located under the drivers area had rusted through and ruptured. *jb

NHTSA complaint #10541983
Jun 25, 2013service brakes

My brake lines rusted at the rear of the lt front wheel splash area. This vehicle has low miles for the year and was not driven in salt or deice. The brake line should not need to be replaced at this time with so much service life left. I was lucky, the brake line burst in my driveway. *tr

NHTSA complaint #10521677
Apr 19, 2013service brakes
Rusty brake lines on 2004 GMC 2500hd sierra. Almost caused me to have an accident because the brake petal went to the floor immediately when the brake line burst. I have pictures of the old rusted brake lines if you would like to see the pictures. Since it seems to be a wide spread problem on GM pickup trucks from researching it on the internet, I'm curious to know when… Read more

Rusty brake lines on 2004 GMC 2500hd sierra. Almost caused me to have an accident because the brake petal went to the floor immediately when the brake line burst. I have pictures of the old rusted brake lines if you would like to see the pictures. Since it seems to be a wide spread problem on GM pickup trucks from researching it on the internet, I'm curious to know when they are going to recall them? Just saw on the news where there is a government recall on 2005-2009 subaru's for the same problem. It cost $1290.00 to repair all the brake lines. *tr

NHTSA complaint #10508778
Nov 11, 2012service brakes

Complete brake failure, when brake line blew out while trying to stop. Prior to hitting car in front, swerved into left turn lane and applied emergency brake. *tr

NHTSA complaint #10483980
Nov 5, 2012service brakes
Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving 40 MPH the vehicle began to shake violently. The contact mentioned that the vehicle was merged to the side of the road and after a few minute restarted the vehicle but the front wheel was locked and smoke was emitting from the hubcaps. After a considerable amount of time the wheels unlocked… Read more

Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving 40 MPH the vehicle began to shake violently. The contact mentioned that the vehicle was merged to the side of the road and after a few minute restarted the vehicle but the front wheel was locked and smoke was emitting from the hubcaps. After a considerable amount of time the wheels unlocked and the vehicle was driven to a dealer for diagnosis. He was informed that the seal in the boost had leaked and contaminated brake fluid and locked up the system. The vehicle was repaired. The failure and current mileage was 140,894. Updated 12/19/12 *cn the consumer stated while traveling 40mph the vehicle stared losing power. Upon further inspection it was found the brakes were smoking. After the smoke settled, the consumer attempted to press the brake pedal. It would not move. After about 3 hours the brakes released. The vehicle was then driven t a repair shop. Updated 1/9/2013 *js

NHTSA complaint #10483364
Sep 18, 2012service brakes
Leaving work I pulled out from the parking lot and drove about 500 yards. Went to apply brakes and pedal went to the floor. I was able to make it back to my work parking lot and stopped the truck. Noticed that brake fluid was pouring from under the truck in two places. One leak was under the drivers area and the other was in front of the left rear wheel. The place I work… Read more

Leaving work I pulled out from the parking lot and drove about 500 yards. Went to apply brakes and pedal went to the floor. I was able to make it back to my work parking lot and stopped the truck. Noticed that brake fluid was pouring from under the truck in two places. One leak was under the drivers area and the other was in front of the left rear wheel. The place I work has a car lift. Put the truck on the lift and the brake lines were rusted through. The truck has enormous amounts of rust on the frame, suspension, and axles. This truck is not my daily driver. I do not live near the ocean nor do I push snow with it. I have never seen brake lines rust out like this. GM stated that I had to take it to a dealer for inspection. After reading up on the topic I know GM won't do anything about the lines. I already ordered stainless steel brake lines for the truck and will install them. Hopefully GM will reimburse owner for this expense. *tr

NHTSA complaint #10475854
Jun 26, 2012service brakes
Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving 25 MPH downhill, the driver was attempting to brake and the pedal depressed to the floor. The contact mentioned that the failure occurred twice before. The vehicle was taken to the dealer, who diagnosed that the brake lines were completely corroded. The manufacturer was made aware of the… Read more

Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving 25 MPH downhill, the driver was attempting to brake and the pedal depressed to the floor. The contact mentioned that the failure occurred twice before. The vehicle was taken to the dealer, who diagnosed that the brake lines were completely corroded. The manufacturer was made aware of the failure and did not offer any assistance. The vehicle was not repaired. The failure mileage was 33,000 and the current mileage was 36,000.

NHTSA complaint #10463144
Mar 26, 2012service brakes, hydraulic, electrical system, electronic stability control (esc)
My truck is a work truck driven by an employee, I have just recently become aware of a condition regarding the instrument cluster, wherein the whole panel does not work, I was advised by the employee that this happened quite some time ago, but was never made aware. I contacted GMC but apparently, because this is considered a special policy recall (only if someone complains -… Read more

My truck is a work truck driven by an employee, I have just recently become aware of a condition regarding the instrument cluster, wherein the whole panel does not work, I was advised by the employee that this happened quite some time ago, but was never made aware. I contacted GMC but apparently, because this is considered a special policy recall (only if someone complains - and within a specified time period 7 yrs or 80,000 miles) they will not repair this defect. I never received a notice, nor was I aware of the problem within that time period. I was further informed by my worker that at the time the panel went out, the fan for the heater/air condition unit appeared to smoke and now it does not work. Here again, I have not received any recall notices for this defect either. Finally, in my attempts to get the cluster repaired, I have been informed that there is a recall on the hydro boost accumulator... I have not once received a recall notice on this vehicle and I purchased this vehicle new. My vehicle has 101,000 miles on it. You would think that a vehicle of this nature would last longer than 100,000. But apparently not... Also, when these is such a major recall out on a vehicle you would think that GMC would contact you and advise you of this problem.. *tr

NHTSA complaint #10453140
Nov 17, 2011service brakes, hydraulic
Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving approximately 50 MPH and attempting to decelerate, the brake pedal went straight to the floorboard abnormally. The vehicle was taken to a dealer where they advised him that the driver side rear steel brake line had failed. They advised him that all brake lines needed to be replaced due to the… Read more

Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that while driving approximately 50 MPH and attempting to decelerate, the brake pedal went straight to the floorboard abnormally. The vehicle was taken to a dealer where they advised him that the driver side rear steel brake line had failed. They advised him that all brake lines needed to be replaced due to the severity of the corrosion. The vehicle was not repaired. The manufacturer was contacted and they offered no assistance. The failure and the current mileages were approximately 38,400.

NHTSA complaint #10436234
Oct 19, 2011service brakes, hydraulic

Brake lines are rotted out. I pushed on my brake pedal while coming to a red light and it went to the floor, the rusted lines had broken and my brakes did not work. Luckily I was not going to fast or to close to the car in front of me so I was able to slow enough to turn off the road by pushing in my parking brake. *tr

NHTSA complaint #10430898
Sep 2, 2011service brakes, hydraulic
While towing 4000# boat, approached traffic signal and applied brakes while moving at approx 10 MPH, the brakes applied and the pedal then bottomed out on the floor. The vehicle veered left and came to a stop after much continued braking effort. The vehicle was driven off the highway at the first safe intersection and examined. Inspection under the drivers side of the frame… Read more

While towing 4000# boat, approached traffic signal and applied brakes while moving at approx 10 MPH, the brakes applied and the pedal then bottomed out on the floor. The vehicle veered left and came to a stop after much continued braking effort. The vehicle was driven off the highway at the first safe intersection and examined. Inspection under the drivers side of the frame revealed rusted through steel brake line from master cylinder and leaking brake fluid onto the street. Vehicle and boat were towed, later inspection revealed four of five steel brake lines at the proportioning valve were rusted to point that replacement was necessary.

NHTSA complaint #10423733
Aug 22, 2011service brakes, hydraulic
This complaint covers my 2004 GMC sierra 2500hd crew cab 4wd. Almost one year ago I had a main brake line blow underneath the drivers side of the truck. The line was so corroded it was no wonder. This incident happened on 9-7-10. I was hooked to my fifth wheel camper and was preparing to pull out of driveway and when I placed foot on brake to shift into drive it blew. … Read more

This complaint covers my 2004 GMC sierra 2500hd crew cab 4wd. Almost one year ago I had a main brake line blow underneath the drivers side of the truck. The line was so corroded it was no wonder. This incident happened on 9-7-10. I was hooked to my fifth wheel camper and was preparing to pull out of driveway and when I placed foot on brake to shift into drive it blew. Thankfully I was just beginning to move. I had the truck towed to my local mechanic and he replaced the line and flushed system. Now again on 8-22-11 same situation occurred. The line blew in exactly the same position as first time only a different line this time. Not to mention the other corrosion on the brake calipers and hardware that rendered my rear brakes useless. Had to replace rotors and pads due to sticking brake pad wearing to point of metal to metal contact. Did I mention I purchased this truck new and it now has only 38,500 miles. Rarely does it get driven in snow and salt. I have all receipts for parts that this problem has caused me. Im just thankful that I wasn't towing as I usually do when im driving this truck. I've talked to my local dealership don hall in ashland, ky and they cite hundreds of trucks having this same problem. When are they going to do something about this. I am a loyal GM fan but I worked at a toyota dealership for two years selling used vehicles. I made it a habit of checking all of our GM truck trade-ins for this rust problem and they too had this. I saw eve

NHTSA complaint #10421078
Aug 22, 2011service brakes, hydraulic
Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact was driving 25 MPH and applied the brakes for a traffic stop when there was a pulsation coming from the brakes. This caused the brakes to be depressed abnormally into the floorboard. The contact could not stop the vehicle until he engaged the emergency brakes. The vehicle was driven to the dealer and after inspection,… Read more

Tl* the contact owns a 2004 GMC Sierra 2500 HD. The contact was driving 25 MPH and applied the brakes for a traffic stop when there was a pulsation coming from the brakes. This caused the brakes to be depressed abnormally into the floorboard. The contact could not stop the vehicle until he engaged the emergency brakes. The vehicle was driven to the dealer and after inspection, the dealer informed him that the brake line was rusted and had ruptured. In addition, the dealer advised that there were no recalls for the failure. The manufacturer was contacted who advised that a representative would later return his call. The vehicle was not repaired. The failure mileage was 42,000. Updated 09/28/2011 *ln *tr

NHTSA complaint #10420915
Aug 14, 2011service brakes, hydraulic
I own a 2004 GMC sierra 2500hd 4wd truck. It has 90,500 miles on it. Multiple brake lines under the driver side door have rusted and are leaking brake fluid. The vehicle is unsafe to drive at this point unless repairs are made costing me over $1000. I cannot drive the truck until repairs are made. It appears after doing some online research that there is already a NHTSA… Read more

I own a 2004 GMC sierra 2500hd 4wd truck. It has 90,500 miles on it. Multiple brake lines under the driver side door have rusted and are leaking brake fluid. The vehicle is unsafe to drive at this point unless repairs are made costing me over $1000. I cannot drive the truck until repairs are made. It appears after doing some online research that there is already a NHTSA investigation concerning premature brake line rusting/failure on GM trucks. I have driven cars that are over 30 years old and they do not have the kind of rust I have on my GMC sierra that is only 7 years old!!! Please make GM do a recall on this design failure. They are endangering the lives of their customers! *tr

NHTSA complaint #10419339
Jun 19, 2011service brakes, hydraulic
Wife and child driving truck, brake pedal went to the floor and service brake indicator came on while on interstate. Stopped at a gas station and filled master cylinder reservoir with fluid. Drove vehicle 8 more miles and traded with me, when I got to the vehicle, I found brake fluid leaking onto ground, found lines corroded beyond belief on driver side frame around wheel… Read more

Wife and child driving truck, brake pedal went to the floor and service brake indicator came on while on interstate. Stopped at a gas station and filled master cylinder reservoir with fluid. Drove vehicle 8 more miles and traded with me, when I got to the vehicle, I found brake fluid leaking onto ground, found lines corroded beyond belief on driver side frame around wheel well. Drove truck home using emergency brake, low speed, and down shifting. No repairs have been performed due to strong belief this is a manufacturer defect. *tr

NHTSA complaint #10407413
Mar 30, 2011service brakes, hydraulicCrash
Lost brakes while driving 35 MPH was able to stop and noticed brake fluid dripping from above gas tank just forward of rear axle on drivers side. New brake line was installed at GMC dealer in july 2010 after it burst going 45 MPH same problem as in july 2010 that caused an accident with property damage to my vehicle and others property after sudden complete brake failure. New… Read more

Lost brakes while driving 35 MPH was able to stop and noticed brake fluid dripping from above gas tank just forward of rear axle on drivers side. New brake line was installed at GMC dealer in july 2010 after it burst going 45 MPH same problem as in july 2010 that caused an accident with property damage to my vehicle and others property after sudden complete brake failure. New line is severely corroded at each green plastic clip after only 7 months.

NHTSA complaint #10394593
Mar 23, 2011service brakes, hydraulic
Tl*the contact owns a 2004 GMC sierra k2500 hd. The contact stated that the anti lock brake system failure was similar to NHTSA campaign id number: 05v379000 (service brakes, hydraulic:antilock). The dealer replaced the brakes in 2008; however, the failure continued to occur. The manufacturer advised the contact that his vehicle was not included in the previous recall and… Read more

Tl*the contact owns a 2004 GMC sierra k2500 hd. The contact stated that the anti lock brake system failure was similar to NHTSA campaign id number: 05v379000 (service brakes, hydraulic:antilock). The dealer replaced the brakes in 2008; however, the failure continued to occur. The manufacturer advised the contact that his vehicle was not included in the previous recall and offered no additional assistance. The current mileage was 29,000 and the failure mileage was 24,000. Updated 09/21/2011 *ln *tr

NHTSA complaint #10392643
Sep 1, 2010service brakes, hydraulic, structure
I was approaching an intersection in my 2004 GMC sierra 4x4 2500hd pickup truck with a 2800 pound trailer when I pressed the brakes to stop. The brake pedal went to the floor and I was unable to stop. The trailer brakes were not enough to stop the vehicle and I continued into the intersection and was almost struck by two other vehicles. They just missed hitting my vehicle… Read more

I was approaching an intersection in my 2004 GMC sierra 4x4 2500hd pickup truck with a 2800 pound trailer when I pressed the brakes to stop. The brake pedal went to the floor and I was unable to stop. The trailer brakes were not enough to stop the vehicle and I continued into the intersection and was almost struck by two other vehicles. They just missed hitting my vehicle and causing serious injuries to myself and my passenger, as well as themselves. When I opened the hood there was brake fluid all over the drivers side of the engine compartment. I had the vehicle towed to the nearest GMC dealer. The dealer told me that a brake line had burst and needed to be replaced. He also stated that all the brake lines were corroded and needed to be replaced at $750.00 per side. He told me that this was a common problem for these vehicles and that these lines only last 4-7 years on average. There is also significant corrosion on the frame. My vehicle is always garaged and regular maintenance is done. The dealer then told me that since we live in a snow belt state that I should expect this and that GMC will not help with the repair. I told him that I am very upset and that I have been a firefighter/paramedic for over 25 years, and if what he just said was true, then I would have had to rescue an awful lot of people from their crashed vehicles if on average brake lines only lasted 4-7 years. I feel that this needs to be reported and investigated because it is a very serious sa

NHTSA complaint #10353376
Jun 26, 2010service brakes, hydraulic

1. Applied brakes when leaving driveway. 2. Brakes failed completely. 3. Brake lines completely rusted out. Right front failed allowing brake fluid and requisite pressure to escape. I replaced the failed section. *tr

NHTSA complaint #10340215
Nov 23, 2009service brakes, hydraulic

At slow speed as I'm coming to a stop I'll feel the ABS brakes kick in and the pedal will go down some more and steering wheel kick to the left and the truck will move a little farther instead of stopping. *tr

NHTSA complaint #10293243
Oct 8, 2008service brakes, hydraulic
Tl*the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that both rear brake pads and rotors were worn, in addition to the front passenger side brake pad and rotor. The contact feels that the brake pads and rotors should not have failed at 36,000 miles. The manufacturer took a report and stated that the failure was not a defect, but rather a part of normal… Read more

Tl*the contact owns a 2004 GMC Sierra 2500 HD. The contact stated that both rear brake pads and rotors were worn, in addition to the front passenger side brake pad and rotor. The contact feels that the brake pads and rotors should not have failed at 36,000 miles. The manufacturer took a report and stated that the failure was not a defect, but rather a part of normal maintenance. They refused to assist with the repair. The vehicle has not been repaired. The current and failure mileages were 36,000. Updated 11/14/08 *cn the consumer stated the brake pads would not move on slides. Updated 11/19/08. *jb

NHTSA complaint #10244715
Apr 21, 2008service brakes, hydraulic
When slowing using the brake system, the vehicle actually loses braking effectiveness for a short time (less than 1 second) just before the vehicle actually stops- at about 3 to 5 MPH. The is then a pulsing feel in the brake pedal and the vehicle then stops. The point is that there is actually a momentary loss of braking effectiveness in the last few moments of a normal stop.… Read more

When slowing using the brake system, the vehicle actually loses braking effectiveness for a short time (less than 1 second) just before the vehicle actually stops- at about 3 to 5 MPH. The is then a pulsing feel in the brake pedal and the vehicle then stops. The point is that there is actually a momentary loss of braking effectiveness in the last few moments of a normal stop. Fortunately, them, only "low speeds" are involved; unfortunately, this is very unsettling when stopping at a busy intersection or in congested traffic. It leaves one wondering if/when the brake function will actually fail altogether. I had the problem investigated by my dealer and was told that it involved the anti lock sensors which may be fixed by cleaning. If that wouldn't fix the problem, the sensors would have to be replaced. Costs: cleaning $160; replacement: $1250. Cleaning did not correct the problem. *tr

NHTSA complaint #10225210
Sep 12, 2007service brakes, hydraulic

Tl*the contact owns a 2004 GMC Sierra 2500 HD. While driving 30 MPH, the brake pedal extended to the floorboard when depressed. The dealer stated that there was rust on the bolt that attached the wheel sensor. As of september 12, 2007, the dealer had not repaired the vehicle. The failure mileage was 40,000 and current mileage was 58,800.

NHTSA complaint #10202782
Aug 1, 2006service brakes, hydraulic

Dt*: the contact stated that the vehicle experienced excessive stopping distance while depressing the brake pedal. The dealer could not duplicate the problem.

NHTSA complaint #10164082
← All 2004 GMC Sierra 2500 HD problems & recalls