Jun 30, 2015service brakes
I was moving the vehicle in the driveway when the break pedal went to the floor. The truck stopped so I got out and looked under it and saw break fluid pouring out of a break line that had completely rusted through. The former owner had already had another break line replaced because his breaks had ruptured due to the lines rusting through while driving at highway speeds and… Read more
I was moving the vehicle in the driveway when the break pedal went to the floor. The truck stopped so I got out and looked under it and saw break fluid pouring out of a break line that had completely rusted through. The former owner had already had another break line replaced because his breaks had ruptured due to the lines rusting through while driving at highway speeds and towing a fifth wheel camper. He was able to avoid wrecking and came to a stop. This truck has low miles and about 90% of its use has been during the summer so it has had limited contact with salted roads yet the entire undercarriage of the vehicle is rusting at an incredible rate. I am fortunate that I was simply moving the truck rather than hauling my camper on the highway which is it's typical use; I and/or others could have been severely injured or killed. The rusting through of the break lines is a safety issue!
NHTSA complaint #10731294
Feb 5, 2015service brakes
Came to intersection for turn, broke and pedal went to floor. *tr
NHTSA complaint #10681397
Oct 26, 2014fuel system, gasoline, power train, service brakes
Brake line leaks, brake stopped working because of rusted brake lines. Also fuel and transmission lines are rusted badly. *tr
NHTSA complaint #10650027
Sep 25, 2014service brakes
Complete brake failure while pulling a 10000 pound trailer in camp ground. The brake lines under the drivers side broke appeared to be corrosion. Truck was towed to repair location. All brake lines were replaced, cost $ 950 dollars. *tr
NHTSA complaint #10639142
Jun 3, 2014service brakes, hydraulic
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated while driving approximately 10 MPH, the brake pedal traveled to the floorboard when depressed. The vehicle eventually came to a stop and was taken to an independent mechanic. The technician diagnosed that both rear brake lines were corroded and needed to be replaced. The manufacturer was not notified of the… Read more
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated while driving approximately 10 MPH, the brake pedal traveled to the floorboard when depressed. The vehicle eventually came to a stop and was taken to an independent mechanic. The technician diagnosed that both rear brake lines were corroded and needed to be replaced. The manufacturer was not notified of the defect. The approximate failure mileage was 150,000. Updated 08/12/2014*lj
NHTSA complaint #10595883
May 4, 2014service brakes
I was driving my 03 sierra, approaching a stoplight at a busy intersection when I applied the brakes. The truck began to slow at first but then the peddle immediately went completely to the floor. I began to pump it but there was no response. I was heading toward the intersection, the light was red, with busy cross traffic. The street I was on is narrow and steep and I… Read more
I was driving my 03 sierra, approaching a stoplight at a busy intersection when I applied the brakes. The truck began to slow at first but then the peddle immediately went completely to the floor. I began to pump it but there was no response. I was heading toward the intersection, the light was red, with busy cross traffic. The street I was on is narrow and steep and I began to pick up speed. I shifted the trans into the lowest gear and stepped on the emergency brake. The truck finally came to a stop in the middle of the intersection, as oncoming cars luckily avoided hitting me. When I went to my mechanic to arrange to have the truck towed, he knew immediately what the problem was. He told me, sight unseen, that the brake line under the driver's side had ruptured. Later, upon inspection, he was correct. He also told me that this was a very common problem with that year. He replaced the line and I thought that had solved the problem; until two days ago. Again, I am driving down a hill and the same thing happened. I was towing a very large trailer this time and the emergency brake had little affect. Luckily, there was little traffic and I was able to ride it out without incident. I have since discovered that this is a problem with not only the 03 year but 4 or 5 years prior also. Another mechanic told me that the entire system of lines should be replaced since GM used a uncoated steel which begins to be compromised within just a few years where salt is heavily
NHTSA complaint #10586414
Feb 6, 2014service brakes
I was driving down the road when my brake peddle went to the floor, I had to use my emergency brake to stop my vehicle. Luckily I swerved to avoid traffic in front of me and was able to stop safely. Upon having my truck towed, my mechanic showed me that my brake line from my master cylinder had rusted out causing brake failure. *tr
NHTSA complaint #10563218
Oct 3, 2013service brakes
I had stopped at a gas station and when I left I was going approximately 35 miles per hour when I put pressure on the brakes and the brake lines ruptured . Was able to get to a repair shop and they said that the lines had rusted through. All lines had to be changed, *tr
NHTSA complaint #10546592
Sep 16, 2013service brakes
Going down a hill approaching a "t" intersection I pressed the brake and went to floor, tried pumping nothing so I put the truck in 3rd gear and then 2nd and shut off my lights to see if any cars where coming into "t" . I need to turn left, luckily no cars made it thru. But I had to cross a hwy before getting home. I did the same thing went from d to 3rd to 2nd, again no cars. Was very lucky. *tr
NHTSA complaint #10543795
Aug 7, 2013service brakes, hydraulic
While driving up to an intersection I applied the brakes and the pedal dropped to the floor, no brakes. The cross traffic was approaching at 50 MPH, and my road stopped so I had to make a left or right. Luckily, by some miracle the oncoming traffic just missed slamming into me. I have never received anything from GM asking for me to have the brake lines checked, even though… Read more
While driving up to an intersection I applied the brakes and the pedal dropped to the floor, no brakes. The cross traffic was approaching at 50 MPH, and my road stopped so I had to make a left or right. Luckily, by some miracle the oncoming traffic just missed slamming into me. I have never received anything from GM asking for me to have the brake lines checked, even though I see online that I am far from alone with this problem. I see you started investigating this issue in 2010 - why haven't you done anything about this? I was almost killed and no one is warning owners of GM trucks I guess when the government owns part of GM they don"t have to worry about recalls....... The consumer stated the reason the brakes failed, were due to rusted out brake lines.
NHTSA complaint #10534020
Jul 30, 2013service brakes
As I began backing out of my drive way my brake peddle went to the floor and I had a rapid decrease in braking power. Upon investigation I noticed brake fluid leaking from the brake lines right above the frame rail on the driver side. If this happened while driving it could have LED to injuries or fatalities especially when such a large and heavy truck suddenly loses braking power. *tr
NHTSA complaint #10532731
Feb 19, 2013service brakes
Was driving down road at speed limit, hit brakes, rear brake line burst (was severely rusted). I was unable to stop vehicle and proceeded through a red light at a busy intersection with my 2 year old on board in his car seat. How we both made it out of that incident unscathed is amazing. I was unable to stop and had to pull off to the shoulder and hit the parking brake. It… Read more
Was driving down road at speed limit, hit brakes, rear brake line burst (was severely rusted). I was unable to stop vehicle and proceeded through a red light at a busy intersection with my 2 year old on board in his car seat. How we both made it out of that incident unscathed is amazing. I was unable to stop and had to pull off to the shoulder and hit the parking brake. It took my son a good 2 months before he was able to rid himself of fear and anxiety due to what happened. *tr
NHTSA complaint #10499202
Jan 29, 2013service brakes
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated that while driving 30 MPH, he attempted to decelerate and the brake pedal went all the way to the floor. The vehicle was taken to a private mechanic who inspected the brakes and noticed there was a hole in the brake line that caused a leak. The mechanic stated that he needed to replace the entire brake line.… Read more
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated that while driving 30 MPH, he attempted to decelerate and the brake pedal went all the way to the floor. The vehicle was taken to a private mechanic who inspected the brakes and noticed there was a hole in the brake line that caused a leak. The mechanic stated that he needed to replace the entire brake line. The manufacturer was not notified. The failure mileage was 99,075. The VIN was not available.
NHTSA complaint #10495046
Nov 5, 2012service brakes
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated that while traveling 20 MPH, he attempted to stop and the brake pedal failed. The brake pedal could not be fully depressed. The contact was able to slow the vehicle to a stop and merge to the side of the road. The vehicle was towed to a private mechanic where it was determined that the brake lines were… Read more
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated that while traveling 20 MPH, he attempted to stop and the brake pedal failed. The brake pedal could not be fully depressed. The contact was able to slow the vehicle to a stop and merge to the side of the road. The vehicle was towed to a private mechanic where it was determined that the brake lines were completely rusted. The vehicle was repaired. The manufacturer was not contacted about the failure. The failure mileage was 108,500 and the current mileage was 108,505. The VIN was not available.
NHTSA complaint #10483431
Oct 18, 2012service brakes
Tl* the contact owns a 2003 GMC Sierra 2500 HD. While driving approximately 15 MPH, the contact depressed the brakes and the brake pedal abnormally traveled to the floorboard. The vehicle was towed to the dealer for diagnostic testing. The tow truck driver noticed that brake fluid was leaking onto the rear axle. The vehicle was not repaired. The approximate failure mileage was 76,000.
NHTSA complaint #10480974
Oct 15, 2012service brakes
Tl* the contact owns a 2003 GMC Sierra 2500 HD utility truck. The contact stated that while traveling 30 MPH, the brakes became inoperable. The contact was able to merge off road where the vehicle was towed to the dealer. The dealer confirmed that the brake lines and brake pressure control module failed. The vehicle was not repaired. The manufacturer was not contacted. The… Read more
Tl* the contact owns a 2003 GMC Sierra 2500 HD utility truck. The contact stated that while traveling 30 MPH, the brakes became inoperable. The contact was able to merge off road where the vehicle was towed to the dealer. The dealer confirmed that the brake lines and brake pressure control module failed. The vehicle was not repaired. The manufacturer was not contacted. The failure and current mileages were not available. The VIN was not available.
NHTSA complaint #10480183
Sep 22, 2012service brakes
During a tire rotation at costco , they discovered brake fluid leaking from the brake lines. Upon a further investigation ,the brake lines are leaking and found to be rusted out. I have been using the vehicle to tow a 2010 air stream and thank god no accident or injury has occurred. *tr
NHTSA complaint #10476753
Sep 14, 2012service brakes
Applied brakes brake light came on along with brake system service needed lost pressure on pedal and all lost fluid still had small amount of braking (brake lines corroded and leaked out fluid ,lines should have been made from stainless steel not cheap steel.) *tr
NHTSA complaint #10475408
Sep 5, 2012service brakes
Trip from long island new york to freeport maine. Traveling 65-70 MPH during trip on highway 95. Arrived in freeport. Checked into hotel. Went out to truck 2 hours later with the intention of attending an event. Stepped on brake, started truck, brake pedal went to the floor. Pumped the brake pedal but it would not recover from the floor. Checked under truck for leaks and… Read more
Trip from long island new york to freeport maine. Traveling 65-70 MPH during trip on highway 95. Arrived in freeport. Checked into hotel. Went out to truck 2 hours later with the intention of attending an event. Stepped on brake, started truck, brake pedal went to the floor. Pumped the brake pedal but it would not recover from the floor. Checked under truck for leaks and found badly rusted brake lines had burst releasing copious amounts of brake fluid. The truck was towed to sears auto department who had to rebuild the entire brake system from the master cylinder to each wheel. Sears had to replace brake lines and calipers since the calipers were also so rusted that they could not be bled. If these lines had burst on the highway; my wife, my son and me would have possibly been killed or severely injured and others on the road may have suffered the same fate. I have never seen this type of rust on any auto I have ever owned. This truck has never been exposed to salt water. Roads are salted in winter on long island. (as an aside, I had to replace the front bumper prior to starting the trip because it had rusted through from behind. It seems that inferior materials were purchased by GM). *tr
NHTSA complaint #10473896
May 15, 2012service brakes, hydraulic, power train
Front brake lines failed on boat ramp on 9/15/2010 rear brake lines failed on 7/20/2011, transmission lines fail on 5/10/2012 I am sure gas lines are next. Truck is a complete rust bucket underneath.
NHTSA complaint #10459420
Mar 29, 2012service brakes, hydraulic
Took truck to dealer for other work and they reported to me the line was leaking and about to rupture. I have 2 jeep products , both in the late 80's with original brake lines and they are fine. You would think that a "younger vehicle would be up to the task of lasting longer than 9 yrs. I've owned older cars and trucks and have never seen anything like this, even my 1964… Read more
Took truck to dealer for other work and they reported to me the line was leaking and about to rupture. I have 2 jeep products , both in the late 80's with original brake lines and they are fine. You would think that a "younger vehicle would be up to the task of lasting longer than 9 yrs. I've owned older cars and trucks and have never seen anything like this, even my 1964 chevy c-10 didn't have this problem and I sold it in 1991 . A co-worker bought my old chevy and at the 30 year mark for it, the brake lines were fine. I believe that along with the manufacture the government should be held accountable also, they allow this subpar equipment on the roads and highways to carry our kids and families, do you think obama's kids would be subjected to danger in this manner. If the director of NHTSA had a failure of this caliber he or she'd be all over this demanding and enforcing a recall . *js
NHTSA complaint #10453473
Mar 1, 2012service brakes, hydraulicCrash
Driving down driveway brake pedal went to floor ran into snow bank unable to stop. *tr
NHTSA complaint #10449991
Feb 20, 2012service brakes, hydraulic
Total brake failure. Discovered brake lines had rusted in several locations through and all needed and were replaced by dealer. *tr
NHTSA complaint #10448527
Feb 18, 2012service brakes, hydraulic
Brake pedal went to floor at 10 MPH from failed brake line, due to excess corrosion on brake lines. *tr
NHTSA complaint #10448403
Dec 26, 2011steering, service brakes, hydraulic, structure
Many components under the truck are severely rusted. Two brake lines failed in august 2011 due to rust. The rest are ready to fail soon. The power steering line rusted out this month (december). Rust at sensors of ABS system causes erratic ABS operation. *tr
NHTSA complaint #10441253
Dec 6, 2011service brakes, hydraulicFire
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated while driving 35 MPH and applying the brake they extended to the floor. He also saw smoke underneath the hood. He drove into a parking lot, checked under the hood and notice that the brake line was broken and sprayed fuel on top of the exhaust. The vehicle was driven to his home. The contact notified the… Read more
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated while driving 35 MPH and applying the brake they extended to the floor. He also saw smoke underneath the hood. He drove into a parking lot, checked under the hood and notice that the brake line was broken and sprayed fuel on top of the exhaust. The vehicle was driven to his home. The contact notified the dealer who stated there were no recalls related to the failure and the vehicle will be repaired at the owners expense. The manufacturer was not notified. The failure mileage was 83,000.
NHTSA complaint #10438697
Nov 26, 2011service brakes, hydraulic
Corroded brake lines. *tr
NHTSA complaint #10437325
Nov 14, 2011service brakes, hydraulic
I was traveling down the road at approx ~30 miles an hour approaching an intersection with a red light. I went to apply the brakes, the pedal depressed with no resistance and no braking response. I applied the brakes harder, with pedal all the way down and received light brake response, enough to stop the vehicle just short of the intersection. I took the truck to an… Read more
I was traveling down the road at approx ~30 miles an hour approaching an intersection with a red light. I went to apply the brakes, the pedal depressed with no resistance and no braking response. I applied the brakes harder, with pedal all the way down and received light brake response, enough to stop the vehicle just short of the intersection. I took the truck to an ase-certified napa auto center, where the diagnosis was that the brake lines were completely corroded, as well as the emergency brake cables. The corrosion of the brake lines/cable resulted in significant loss of brake fluid, and rendered the emergency brake useless. The total cost of repair is upwards of $1800.00 there was no advanced warning of this failure--no warning lights appeared before or after the failure. This could have been catastrophic and feel that this is a design, assembly or materials flaw that puts public safety at risk. *tr
NHTSA complaint #10435527
Oct 2, 2011service brakes, hydraulic
On 09-30-2011 as I left my residence I got approximately one block away and started down a small but steep hill that intersects with an other subdivision street. At that intersection there is a stop sign, when I applied the brakes to slow for the stop sign the brake pedal went to the floor. I tried pumping the brakes and still had very little to no brakes. There were no other… Read more
On 09-30-2011 as I left my residence I got approximately one block away and started down a small but steep hill that intersects with an other subdivision street. At that intersection there is a stop sign, when I applied the brakes to slow for the stop sign the brake pedal went to the floor. I tried pumping the brakes and still had very little to no brakes. There were no other vehicle in the area, and was able to gear down and ended up slowing going into the intersection where I finally got the vehicle stopped. I was able to get the truck back to the house by going very slow in low gear and using the parking brake. Upon parking the truck and inspecting the system, found the brake fluid level was low. Upon further inspection I found fluid on the ground under the drives seat area. On checking I found the brake lines in the area of the brake controller area were extremely rusted and the line going to the rear brakes had rusted through. I will have all the brake lines to and from the brake controller replaced this week due to the extremely poor condition of the lines from the rust. *tr
NHTSA complaint #10428174
Sep 17, 2011service brakes, hydraulic
Fortunately I was in my driveway when my brake pedal went to the floor. I had it towed and the mechanic replaced a line. He went for a road test and another line blew out. This was fixed and I was told that all of the lines look bad and it would be $700 to replace all and this seemed to be common on the chevy and GMC trucks. This truck is garage kept - why would all of the… Read more
Fortunately I was in my driveway when my brake pedal went to the floor. I had it towed and the mechanic replaced a line. He went for a road test and another line blew out. This was fixed and I was told that all of the lines look bad and it would be $700 to replace all and this seemed to be common on the chevy and GMC trucks. This truck is garage kept - why would all of the brake lines be bad? This is a GMC sierra 2500hd extended cab 4wd truck. *tt
NHTSA complaint #10425883
Aug 16, 2011service brakes, hydraulicCrash
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated that while driving 15 MPH, the brakes were depressed, but the vehicle did not stop until coasting into a tree. The contact also stated that the vehicle was not destroyed and he did not consider the incident to be a crash. The vehicle was taken to an authorized dealer and the failure diagnostic test indicated… Read more
Tl* the contact owns a 2003 GMC Sierra 2500 HD. The contact stated that while driving 15 MPH, the brakes were depressed, but the vehicle did not stop until coasting into a tree. The contact also stated that the vehicle was not destroyed and he did not consider the incident to be a crash. The vehicle was taken to an authorized dealer and the failure diagnostic test indicated that the ABS system failed to operate sufficiently. The manufacturer was notified and the vehicle was repaired. The failure mileage was 41,692 and the current mileage was 41,750. Updated 09/21/11*lj the dealer repalced the left and front speed sensor. Updated 11/04/11
NHTSA complaint #10419612
Jun 7, 2011service brakes, hydraulic
Brake lines are all corroded and rusty. *tr
NHTSA complaint #10405383
May 23, 2011service brakes, hydraulic
Tl* the contact owns a 2003 GMC sierra 2500. The contact stated that when applying the brakes, the brake pedal was depressed to the floorboard. The contact then discovered that the brake lines were rusted. The dealer was not informed and the manufacturer was not made aware of the failure. The vehicle was taken to a private mechanic where the vehicle was repaired. The… Read more
Tl* the contact owns a 2003 GMC sierra 2500. The contact stated that when applying the brakes, the brake pedal was depressed to the floorboard. The contact then discovered that the brake lines were rusted. The dealer was not informed and the manufacturer was not made aware of the failure. The vehicle was taken to a private mechanic where the vehicle was repaired. The current mileage was 70,000 and the approximate failure mileage was 21,000.
NHTSA complaint #10402386
May 23, 2011service brakes, hydraulic
Hydraulic brakes failed without warning while driving on a back road pulling the trailer with a 500 lb mower in the trailer. Brake fluid poured from the behind the driver door under from the frame near the fuel filter and brake line distribution block. Front brake lines replaced one year ago after an accident where the brakes also failed and front brake lines replaced. … Read more
Hydraulic brakes failed without warning while driving on a back road pulling the trailer with a 500 lb mower in the trailer. Brake fluid poured from the behind the driver door under from the frame near the fuel filter and brake line distribution block. Front brake lines replaced one year ago after an accident where the brakes also failed and front brake lines replaced. 2003 GMC sierra 2500 4wd with about 40k mileage. Brake failure has occurred twice with this vehicle...I have another car, dodge grand caravan with 97k and no brake line problems. Stays in the same driveway and drives the same roads. *tr
NHTSA complaint #10402369
Mar 13, 2011service brakes, hydraulic
Rupture brake line above gas tank just applying depressing the brake pedal causing one brake line to rupture from rust. *tr
NHTSA complaint #10390003
Jan 27, 2011service brakes, hydraulic
Both front ABS sensors failed due to corrosion, causing increased stopping distance. *tr
NHTSA complaint #10379358
Jan 27, 2011service brakes, hydraulic
While applying brakes in traffic brake pedal went to floor and truck would not stop. Brake line underneath vehicle was corroded and burst, causing brake fluid leak. *tr
NHTSA complaint #10379352
Jan 27, 2011parking brake
Parking brake failure. *tr
NHTSA complaint #10379356
Dec 31, 2010service brakes, hydraulic
Brake line rupture, 2003 GMC sierra 2500hd pickup. Total loss of braking while stopping for traffic at 60 MPH. All lines were rotted and had to replaced. Crash was avoided because other cars realized I had lost braking and moved out the way. Did not report until now(dec 2010) because I thought it was an isolated incident. Now finding out that it is prevalent, so much, that… Read more
Brake line rupture, 2003 GMC sierra 2500hd pickup. Total loss of braking while stopping for traffic at 60 MPH. All lines were rotted and had to replaced. Crash was avoided because other cars realized I had lost braking and moved out the way. Did not report until now(dec 2010) because I thought it was an isolated incident. Now finding out that it is prevalent, so much, that I have warned friends about it and am finding it to be quite common. *tr
NHTSA complaint #10373592
Oct 8, 2010service brakes, hydraulic
The brakes failed when I tried to stop. The truck was taken a auto repair shop. They told me the brake lines had failed due to rust. The brake lines from the master cylinder and the hydraulic pump had to be replaced. The brake lines from the hydraulic pump and the front wheels had to replaced also. *tr
NHTSA complaint #10359666