CarProblemsDB

2002 GMC Sierra 2500 HD brakes problems

63 owners reported brakes problems — 62% of all 101 complaints about the 2002 GMC Sierra 2500 HD.

Brakes complaints by GMC Sierra 2500 HD year

200523
200437
200356
200263
200153

What owners report

May 9, 2015service brakes

Rear steel brake line failure while in parking lot, complete loss of braking ability

NHTSA complaint #10715461
Apr 24, 2015service brakes

Tl* the contact owns a 2002 GMC Sierra 2500 HD. The contact stated that while driving 5 MPH, when the brake pedal was depressed and the brakes failed. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was 60,000.

NHTSA complaint #10712739
Feb 28, 2015service brakes, fuel/propulsion system
Driving into driveway applied brakes , pedal went right to the floor no warning light or any indication of a problem got out of truck and found fluid dripping off frame by fuel tank. Ruptured line above tank on frame, other brake lines also look corroded. After some research I found this to be a common problem on GM trucks . Owners need to be made aware of this problem… Read more

Driving into driveway applied brakes , pedal went right to the floor no warning light or any indication of a problem got out of truck and found fluid dripping off frame by fuel tank. Ruptured line above tank on frame, other brake lines also look corroded. After some research I found this to be a common problem on GM trucks . Owners need to be made aware of this problem before someone is seriously hurt. I believe GM should be forced to repair the defective lines. *tr

NHTSA complaint #10691237
Nov 4, 2014service brakes

Pulling out of my driveway onto the street. Applied the brakes when reaching the end of the driveway and brake pedal when completely to the floor. Was able to stop, being that I was only going around 2 MPH at the time. When I got out of the truck, I saw a large amount of brake fluid on the driveway from a burst brake line. *tr

NHTSA complaint #10652609
Sep 12, 2014service brakes

Brakes failed while driving down road. All brake lines are severely rusted. Is their a galvanic reaction between lines and truck that is causing this? Have never had brake lines rust as badly on other vehicles that were older than this one. *tr

NHTSA complaint #10632686
Sep 6, 2014service brakes
I had been driving for 15-20 miles both on and off the highway and the vehicle stopped fine. I was traveling at about 60 MPH and was coming up on highway traffic that was at a standstill . I stepped on the brake peddle and it went strait to the floor, absolutely no brakes at all and no even a hint this was about to happen. I was able to swerve out of the way, narrowly… Read more

I had been driving for 15-20 miles both on and off the highway and the vehicle stopped fine. I was traveling at about 60 MPH and was coming up on highway traffic that was at a standstill . I stepped on the brake peddle and it went strait to the floor, absolutely no brakes at all and no even a hint this was about to happen. I was able to swerve out of the way, narrowly missing the vehicle in front of me, and used the transmission and e brake to get the vehicle stopped on a grassy shoulder. Had a vehicle been next to me or a less experienced driver been behind the wheel, it may have been a much worse outcome . I know at least 10 people who own similar vehicles and everyone has had a brake line failure at some point. GM needs to step up and cover this before someone else get hurt or killed! *tr

NHTSA complaint #10631205
Jul 20, 2014service brakes
2002 GMC sierra 2500hd 4x4 4dr complete brake failure when moving vehicle at hunt camp.brake pedal went completely to floor.rusted brake lines blew under drivers door location.local mechanic replaced lines from master cyl. To ABS device. If this had happened the day before,with truck loaded with supplies ,eqpt.,and towing an atv on a trailer,no way could I have stopped… Read more

2002 GMC sierra 2500hd 4x4 4dr complete brake failure when moving vehicle at hunt camp.brake pedal went completely to floor.rusted brake lines blew under drivers door location.local mechanic replaced lines from master cyl. To ABS device. If this had happened the day before,with truck loaded with supplies ,eqpt.,and towing an atv on a trailer,no way could I have stopped that vehicle! I still need to replace all remaining rusted lines going to wheels. *tr

NHTSA complaint #10614850
Jul 14, 2014service brakesCrash

Backing my truck down a boat launch to put a pwc in. As I applied the brake at the bottom of the ramp, the pedal went to the floor, losing all brakes. Since I was close to the water, by the time I got it into forward, it was already over the edge of the ramp into the water. Submerged up to the bottom of the roof. A total loss. *tr

NHTSA complaint #10610520
Jul 13, 2014service brakes

Steel brake line ruptured with no warning under the drivers side floor panel. It was the line from the master cylinder to the anti-lock brake actuator. Read dozens of online postings about this being a huge problem and was encouraged to report it. Safely stopping the truck (empty) was very hard and I couldn't imaging what would have happened if I had been pulling a trailer, which is very common on this truck. *tr

NHTSA complaint #10610139
Jul 8, 2014service brakes

Approaching a stop light of a 55 MPH road and applied the brakes. The truck failed to stop. I went through the red light but did not hit any other cars. *js

NHTSA complaint #10608834
Jun 5, 2014service brakes
Brakes went out no warning, after looking on drivers side seat under truck where fluid was running out saw where brake line was rusted and it busted. So I took several pictures and called GMC, they in turn towed my truck to auffenberg of carbondale, illinois at no charge. At this time I started researching the rusted brake problem and found where alan adler (manager product… Read more

Brakes went out no warning, after looking on drivers side seat under truck where fluid was running out saw where brake line was rusted and it busted. So I took several pictures and called GMC, they in turn towed my truck to auffenberg of carbondale, illinois at no charge. At this time I started researching the rusted brake problem and found where alan adler (manager product safety communications) for GM said on (abc news rusted brake lines) where they were offering a (kit) to have the rusted brake lines repaired for a cost to us of $500.00. So now today 06/05/2014 my truck is done at a cost of $1188.05 to me for the dealer knows nothing of this. I have tried to contact alan adler through GM and no one knows who he is, I have sent many complaints and talked with many people and no one seems to know what I am talking about. My ref.# [xxx] with the complaint dept. So if this man can say on the news that they have this kit and that all the dealers were told about it how can they lie and charge the people what they want. Thank you information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr

NHTSA complaint #10596344
Apr 5, 2014service brakes

Rear brake line rusted out over fuel tank where line runs on top of frame rail. All brake lines rusted. Also fuel lines rusted. Can or will fail at anytime. May cause an accident. No brake failure light!!!! *tr

NHTSA complaint #10577616
Dec 13, 2013service brakesCrash
The vehicle was parked on a 35-40 degree sloped driveway. Got in, stepped on brake,started vehicle, released emergency brake, shift into reverse, and brake pedal went to the floor, with truck rolling backwards. Wheel was turned, and truck hit a side of retaining wall. It did not roll back excessively fast, but it could not stop in time to avoid hitting the wall. Found… Read more

The vehicle was parked on a 35-40 degree sloped driveway. Got in, stepped on brake,started vehicle, released emergency brake, shift into reverse, and brake pedal went to the floor, with truck rolling backwards. Wheel was turned, and truck hit a side of retaining wall. It did not roll back excessively fast, but it could not stop in time to avoid hitting the wall. Found badly corroded brake lines. One had ruptured right behind the driver's front wheel fender well. *tr

NHTSA complaint #10555963
Dec 8, 2013service brakes

Rotted out brake lines @ 118,000 miles . Should be a recall . No accident but was pulling my boat at time of failure. Could have been a very bad accident . Just finished changing all the brake lines what a job. Between this n the injectors this truck was a poor value. All done with GM had too many problems with their trucks with no support from GM or it's dealers. Lost lifetime customer. *tr

NHTSA complaint #10555214
Sep 25, 2013service brakes

No brakes! Pedal to the floor. Rusted brake lines. *js

NHTSA complaint #10545271
Jun 12, 2013service brakes

Tl* the contact owns a 2002 GMC Sierra 2500 HD. The contact stated that while driving 20 MPH, the brakes failed without warning. The vehicle was not repaired and the manufacturer was not notified. The approximate failure mileage was 123,000. *tr

NHTSA complaint #10519571
Dec 13, 2012service brakesCrash

I was exiting my driveway, which is very steep,the brake pedal went to the floor with no warning,lamps or otherwise. My vehicle surged across both lanes and wound up in the woods. *tr

NHTSA complaint #10488737
Nov 21, 2012steering, service brakes
Vehicle is a 2002 GMC hd 2500 pickup truck with a duramax diesel engine, and 5 speed allison transmission while driving on surface streets, the power brakes and steering both went out simultaneously. Stopping required both feet on pedal, and steering was nearly impossible. Problem traced to the "hydroboost" and the power steering pump. Both were replaced along with the… Read more

Vehicle is a 2002 GMC hd 2500 pickup truck with a duramax diesel engine, and 5 speed allison transmission while driving on surface streets, the power brakes and steering both went out simultaneously. Stopping required both feet on pedal, and steering was nearly impossible. Problem traced to the "hydroboost" and the power steering pump. Both were replaced along with the high pressure hose. Evidently, the pump failed to yield any boost pressure, which in turn rendered power steeling and brakes inoperative. A very dangerous situation. The tow truck that responded indicated that they have had multiple failures of the same items (87 ot 8 GMC hd trucks) and in blogs with other GMC/chevy diesel owners it appears to be a common defect. There were no noises, or other indicator of pending problems. Contact with the dealer revealed that " I should change the ps fluid every 2 years: (not in the maintenance section of owner manual). *tr

NHTSA complaint #10485398
Oct 18, 2012service brakes

The truck would not stop at stop sign and the brake goes clear to the floor before slows to a stop. *tr

NHTSA complaint #10480999
Oct 15, 2012service brakes

A brake line ruptured causing loss of stopping power. Truck was not able to slow enough to make originally-planned turn. Truck was safely returned home using emergency brake and engine braking. Upon inspection, a leaking brake line was found between the master cylinder and ABS module. All brake lines were found to be severely corroded. No warning lights illuminated on the dash. *tr

NHTSA complaint #10480160
Oct 12, 2012service brakes

I had an unexpected brake failure caused by the rust through of the brake line under the driver seat. It was fortunate that I was in a parking lot and going at a slow speed at the time. I had to replace the entire brake line system as there was rust on all the lines. The repair cost was $741.89. I have had other GM vehicles, and have never experienced this type of failure before. *tr

NHTSA complaint #10479945
Oct 10, 2012service brakes
Was traveling on a straight stretch of road approaching a red light. As I attempted to apply the brakes the brake pedal went straight to the floor - the vehicle would not stop. I then dropped the transmission from "d" or drive to "l1", engaged the "tow setting" of the transmission, and applied the parking brakes while maintaining the parking disengagement lever in the "up"… Read more

Was traveling on a straight stretch of road approaching a red light. As I attempted to apply the brakes the brake pedal went straight to the floor - the vehicle would not stop. I then dropped the transmission from "d" or drive to "l1", engaged the "tow setting" of the transmission, and applied the parking brakes while maintaining the parking disengagement lever in the "up" position in order to stop the truck. The brakes failed. GM dealership confirmed that the brake lines had rusted through. The entire brake system froze in place resulting in the replacement of the lines, rotors, discs. *tr

NHTSA complaint #10479522
Oct 1, 2012service brakes, hydraulic, service brakesCrash
I was driving my 2002 GMC Sierra 2500 HD on i95 when traffic came to a sudden stop. I slammed on the brakes at which point the ABS system started pulsing the brakes, but the brake pedal suddenly went to the floor with no further brake response. Thankfully, the brakes slowed the truck enough prior to failure to prevent a collision at 65 MPH. I hit the car in front of me at… Read more

I was driving my 2002 GMC Sierra 2500 HD on i95 when traffic came to a sudden stop. I slammed on the brakes at which point the ABS system started pulsing the brakes, but the brake pedal suddenly went to the floor with no further brake response. Thankfully, the brakes slowed the truck enough prior to failure to prevent a collision at 65 MPH. I hit the car in front of me at ~5-10 MPH, causing bumper damage to my truck and the car in front of me. I was able to get the car to the side of the road and to my horror I had no brakes. The vehicle was towed to a local authorized GMC dealer who has maintained the truck for me. They confirmed that the brake lines catastrophically failed when I slammed on the brakes. The rusted brake lines burst when I slammed on the brakes. They indicated that all of the brake lines had to be replaced do to rust throughout. I can't believe I have been driving this truck around with a pending catastrophic brake failure without warning from GM or the servicing dealer. If the word is not put out to owners of affected GMC truck, lives will be lost. I shudder to think what could have happened if I had been pulling up to a pedestrian filled crosswalk when the failure occurred. Updated 10/03/12*lj *tr

NHTSA complaint #10478215
May 24, 2012service brakes
Was heading down the street, coming to a stop sign. Slowing down, got to about 9 MPH, and then the brake pedal went to the floor, and was unable to stop in time and went into the intersection and finally stopped 30 feet after the stop sign with the brake pedal all the way on the floor. Got the truck home, somewhat safely, and found out that all of the brake lines were rusted,… Read more

Was heading down the street, coming to a stop sign. Slowing down, got to about 9 MPH, and then the brake pedal went to the floor, and was unable to stop in time and went into the intersection and finally stopped 30 feet after the stop sign with the brake pedal all the way on the floor. Got the truck home, somewhat safely, and found out that all of the brake lines were rusted, and ended up having to replace all of the lines due to them crumbling when touching them. *tr

NHTSA complaint #10459586
Mar 3, 2012service brakes, hydraulic

Brake line failure due to rust. All brake lines had to be replaced. *tr

NHTSA complaint #10450168
Jan 21, 2012service brakes, hydraulicCrash1 injured

GMC Sierra 2500 HD 2002 rotted brake lines failure caused $4500 in damage to the truck . Wrist injury to my wife. Oil and tranny fluid all over driveway stained. $5000 in damage to my vw beetle resulting in a total loss to this vehicle!!!! *tr

NHTSA complaint #10444734
Dec 6, 2011service brakes, hydraulic

Brake lines are severely corroded and look ready to fail, and I find out that this is a common complaint and all the brake lines should and must be replaced by general motors. The GMC and chevrolet 2500hd models are notorious for this malady, and the ntsb should do their job and force GM to replace at no charge, the vehicles brake lines. *tr

NHTSA complaint #10438768
Aug 4, 2011service brakes, hydraulic

Tl* the contact owns a 2002 GMC Sierra 2500 HD. The contact stated that the brake lines broke as a result of corrosion. The vehicle was not taken to the dealer. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure and current mileage was 101,000. Updated 9/13/11 *cn updated 11/23/11

NHTSA complaint #10417111
Jul 19, 2011service brakes, hydraulic

During routine maintenance in the shop the truck was started to move it and the brake line burst near the point the brake line exits the frame rail near the rear axle. All rear braking was lost. If this had occurred on the highway it could have been a catastrophic event. *kb

NHTSA complaint #10413575
Apr 25, 2011service brakes, hydraulic
Tl* the contact owns a 2002 GMC Sierra 2500 HD. The contact stated that the ABS activated independently at reduced speeds when coming to a complete stop. The vehicle was taken to a local repair shop but the vehicle was not inspected or repaired. The contact called the manufacturer who advised that the vehicle was not included in the recall under NHTSA campaign id number:… Read more

Tl* the contact owns a 2002 GMC Sierra 2500 HD. The contact stated that the ABS activated independently at reduced speeds when coming to a complete stop. The vehicle was taken to a local repair shop but the vehicle was not inspected or repaired. The contact called the manufacturer who advised that the vehicle was not included in the recall under NHTSA campaign id number: 05v379000 (service brakes, hydraulic: antilock). The vehicle was not repaired. The current mileage was approximately 89,000 and the failure mileage was approximately 88,000. Updated 06/01/11*lj updated 06/02/11

NHTSA complaint #10397355
Apr 23, 2011service brakes, hydraulic, equipment
I applied my brakes on my GMC truck and they failed . The brake tubing rusted thru at the ABS unit. Upon further inspection it was determined that all the brake lines were rusted severely. I tried to find pre bent lines and they are not avail. From GM and not avail from aftermarket for a 2002 GMC 2500hd 2wd or any GMC from dealer.frme and undercarriage is rusted worse the my… Read more

I applied my brakes on my GMC truck and they failed . The brake tubing rusted thru at the ABS unit. Upon further inspection it was determined that all the brake lines were rusted severely. I tried to find pre bent lines and they are not avail. From GM and not avail from aftermarket for a 2002 GMC 2500hd 2wd or any GMC from dealer.frme and undercarriage is rusted worse the my 1983 and brake rotors rusted and flaked away. *tr

NHTSA complaint #10397194
Mar 26, 2011service brakes, hydraulic

Brake failure due to rusted brake line, truck lost all brake fluid! *tr

NHTSA complaint #10392965
Jan 23, 2011service brakes, hydraulic
Three brake lines ruptured simultaneously causing an inability to stop the vehicle. The cause of failure was related to an extensive amount of corrosion on all of the brake lines on the vehicle. Complete replace is necessary. There is a regional recall on this exact issue but does not include my state. There are considerable reports of this failure across the country but GM… Read more

Three brake lines ruptured simultaneously causing an inability to stop the vehicle. The cause of failure was related to an extensive amount of corrosion on all of the brake lines on the vehicle. Complete replace is necessary. There is a regional recall on this exact issue but does not include my state. There are considerable reports of this failure across the country but GM and even worse NHTSA fails to force a nationwide recall of this potentiality deadly failure. A simple search of the internet will prove this defect is not constrained to only the rust belt states. My '66 chevy still has the original brake lines with no signs of degradation however my '02 GMC requires the replacement of all metal lines on the vehicle. The existence of a current regional recall proves that GM admits to the problem! This failure needs to be corrected nationwide. *ln

NHTSA complaint #10378349
Oct 13, 2010service brakes, hydraulic

The anti-lock brakes system failed. While braking at approximately 2-10 MPH, the brakes lock up. This lock-up occurs at all stop situations. The lock-up causes skidding, and longer stopping distance. *tr

NHTSA complaint #10360378
Sep 11, 2010service brakes, hydraulic, structure

Backing up to my trailer when my brake lines blew out on my 2002 GMC Sierra 2500 HD. Also underneath of truck is soo rusted and bottom of doors are also rusting through. *tr

NHTSA complaint #10354991
Sep 3, 2010service brakes, hydraulic, parking brake, structure
I was parked in a friends driveway and was about to leave when I released the parking brake stepped on the brake pedal and put my 2002 GMC 2500hd truck into gear. I started driving down the street and approached a stop sign, when I applied the brakes the pedal went straight to the floor. I pulled off to the side of the road and opened the hood when I noticed brake fluid all… Read more

I was parked in a friends driveway and was about to leave when I released the parking brake stepped on the brake pedal and put my 2002 GMC 2500hd truck into gear. I started driving down the street and approached a stop sign, when I applied the brakes the pedal went straight to the floor. I pulled off to the side of the road and opened the hood when I noticed brake fluid all over the frame in the engine compartment. Upon further investigation I found all the brake lines to be severely rusted and at least one of them ruptured. I was driving with my 9 month old son at the time of the incident and thank god nobody was coming the other way down the road. I had the truck towed to my home where it sits awaiting a total brake line replacement. The underneath of the truck is so severely rusted I think GMC is liable and should issue a recall to correct the problem. *tr

NHTSA complaint #10353829
Jun 15, 2010service brakes, hydraulicCrash

Brake lines burst under heavy braking due to accident avoidance situations. First time the rear line burst, second time the front left line burst by the ABS unit. *tr

NHTSA complaint #10336546
May 24, 2010service brakes, hydraulic

ABS triggers for no apparent reason when applying brakes to my 2002 GMC Sierra 2500 HD. I'm told there was some type of a recall due t corrosion of an ABS wheel speed sensor, but no dealer will speak to me. *tr

NHTSA complaint #10331891
Apr 10, 2010service brakes, hydraulic
I was plowing snow on the common driveway that I share with 3 other neighbors and came around a bend to meet my neighbor's son on his atv. I slammed on the brakes and the pedal went to the floor. Fortunately the pile of snow in front of the plow helped stop my truck. The atv operator dodged in to the snow bank. There was no contact. I found that I had multiple brakeline… Read more

I was plowing snow on the common driveway that I share with 3 other neighbors and came around a bend to meet my neighbor's son on his atv. I slammed on the brakes and the pedal went to the floor. Fortunately the pile of snow in front of the plow helped stop my truck. The atv operator dodged in to the snow bank. There was no contact. I found that I had multiple brakeline failures on my truck. I have had a previous brake line failure in 2008 but could not find the work order for repairs to verify date and mileage. *tr

NHTSA complaint #10324885
Apr 10, 2010service brakes, electric

Depressed ab brakes to avoid deer, brake went all the way to floor board before stopping. Brake lines corroded and had to be replaced. *tr

NHTSA complaint #10324861
← All 2002 GMC Sierra 2500 HD problems & recalls