Nov 16, 2026engine
Vehicle: 2020 GMC Sierra 1500 at4, 6.2l v8 (l87), VIN [xxx], approximately 106,000 miles. The engine began running rough, the check engine light came on, and the truck set code p0305 (cylinder 5 misfire). The truck is at jim ellis GMC, [xxx]. On xxx, jim ellis GMC diagnosed low compression on cylinder 5 with an active misfire and recommends engine replacement, estimate… Read more
Vehicle: 2020 GMC Sierra 1500 at4, 6.2l v8 (l87), VIN [xxx], approximately 106,000 miles. The engine began running rough, the check engine light came on, and the truck set code p0305 (cylinder 5 misfire). The truck is at jim ellis GMC, [xxx]. On xxx, jim ellis GMC diagnosed low compression on cylinder 5 with an active misfire and recommends engine replacement, estimate $14,209.11, with the oil cooler and hoses included in the estimate in case metal is found in the oil. The l87 engine in this truck is the same engine at issue in [xxx] et al. V. General motors, no. Xxx ([xxx]d[xxx]), covering 2019–2024 sierra 1500s with the 6.2l l87. My 2020 has the same l87 engine but falls outside the recall model years, so no recall remedy is available. I am requesting that NHTSA record this failure and consider whether the defect population should include 2019–2020 l87 engines. Dealer: jim ellis GMC, [xxx] — diagnosis: low compression on cylinder 5 with active misfire; engine replacement recommended, estimate $14,209.11. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
NHTSA complaint #11778253
Oct 28, 2026engine
6.2 liter engine failed at 59,300 miles. Being replaced right now with remanufactured engine. 2020 GMC sierra is not part of recall but others have had problems as well
NHTSA complaint #11774319
Oct 23, 2026power train, engine
I own a 2020 GMC sierra at4. It has developed a shudder when cruising on the highway or driving in town around 1500rpm. I believe it is coming from the transmission. A local shop mentioned the torque converter. The shudder feels like a delay in power and makes it difficult to hold speed or accelerate when needed.
NHTSA complaint #11773333
Oct 23, 2026steering, engine
This morning it seems as if my 6.2l GM motor threw a rod. All the initial sounds and check engine information point toward that. I will be taking it to a dealer to confirm the issue. Data center driving ability and sounds indicate steering was affected as well or is somehow connected.
NHTSA complaint #11773206
Oct 19, 2026engine
I was driving and my truck shut down on me while I was driving down the road, I had to get it towed to the dealership where it was confirmed that the motor would need to be replaced. There was no warning, it just turned off and luckily I was able to coast to a safe area to wait for the tow truck.
NHTSA complaint #11772065
Oct 17, 2026power train, engine, fuel/propulsion system
[xxx] general motors company p.o. Box 33170 detroit, mi 48232-5170 c/o franklin, customer support re: formal demand for buyback – 2020 GMC sierra at4 black widow VIN: [xxx] | 6.2l engine recall ~ 25v-274. Plus ~ GM 10-speed transmission, multiple recalls dear GMC legal, I am providing written notice as required by 15 u.s.c. §2310 and new york state lemon law. This vehicle… Read more
[xxx] general motors company p.o. Box 33170 detroit, mi 48232-5170 c/o franklin, customer support re: formal demand for buyback – 2020 GMC sierra at4 black widow VIN: [xxx] | 6.2l engine recall ~ 25v-274. Plus ~ GM 10-speed transmission, multiple recalls dear GMC legal, I am providing written notice as required by 15 u.s.c. §2310 and new york state lemon law. This vehicle substantially impairs the safety, use, and value of my truck, and I am requesting a full buyback. The facts: on [xxx], the vehicle was taken out of service and remained at the shop for 11 weeks. It was returned with yellow marking paint splattered on the exterior, floor mats, and brake pedal. On [xxx] — with fewer than 400 miles on the replacement engine — the engine and/or transmission suddenly shut off at 55 MPH on [xxx]. It restarted with a violent boom, then cycled between shutting off and restarting with loud clacking and shaking for the remainder of the drive. I was forced to drive at 25 MPH with hazard lights to reach home. The legal basis: this is a safety defect on a vehicle subject to recall 25v-274. GM was on notice of this known, concealed defect. The vehicle has been out of service for 30+ cumulative days. I have been denied a reasonable opportunity to cure. The vehicle has caused me severe and ongoing psychological distress, imminent and uncontrolled danger to my life, and total and continuing loss of use for its fundamental purpose. My demand: 1.full buyback under new york state lemon law
NHTSA complaint #11771820
Oct 15, 2026engine
Driving down road started to hear a weird growling knocking sound and noticed a reduction of power. Also noticed lower then normal oil pressure. Changed oil found metal shavings in the oil. Sent to chevy dealership. Diagnosed "rod bearing failure" needs new engine.
NHTSA complaint #11771297
Oct 13, 2026engine and engine cooling
The contact owns a 2020 GMC Sierra 1500. The contact stated that while driving at an undisclosed speed, the vehicle suddenly entered limp mode without warning. The vehicle was taken to the dealer, where the computer was reflashed and the vehicle temporarily returned to normal operation; however, the failure recurred and the vehicle was returned to the dealer. The contact… Read more
The contact owns a 2020 GMC Sierra 1500. The contact stated that while driving at an undisclosed speed, the vehicle suddenly entered limp mode without warning. The vehicle was taken to the dealer, where the computer was reflashed and the vehicle temporarily returned to normal operation; however, the failure recurred and the vehicle was returned to the dealer. The contact noticed a burnt odor coming from the engine compartment, along with engine bay cooling fans running at an unusual rate. Upon further inspection, the dealer diagnosed the failure as a defective coolant valve. The contact associated the failure with GM special coverage tsb n252508341; however, the VIN was not included in the coverage program. The manufacturer was notified of the failure. The failure mileage was 107,000.
NHTSA complaint #11770786
Oct 8, 2026engine
I have a 2020 GMC Sierra 1500 at4 with the l87 6.2l v8. The cam shaft and lifters have failed for a 2nd time. The first time happened in 2022. It was under warranty and happened at approximately 40,000 miles. This last time it happened in 2026 and was at 125,000 miles - both for the same thing - cam shaft and lifters. Both were sudden failures and luckily I was on a… Read more
I have a 2020 GMC Sierra 1500 at4 with the l87 6.2l v8. The cam shaft and lifters have failed for a 2nd time. The first time happened in 2022. It was under warranty and happened at approximately 40,000 miles. This last time it happened in 2026 and was at 125,000 miles - both for the same thing - cam shaft and lifters. Both were sudden failures and luckily I was on a highway that wasn't buy at the time. This time it is costing me $10,000 to fix. They have had the truck for two months now. My understanding is the significant recall that occurred was being investigated to see if it should be expanded. I believe it should have been expanded. Whatever came of that decision? GM told me they could offer no help as my truck was out of warranty and my truck was not on the recall list. I'm curious if it will be expanded and what would happen in my situation if it is expanded. GM has deleted the support message chain that went on for four weeks where I was trying to get them to cover it under the recall and/or explaining the entire situation. Thanks, [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
NHTSA complaint #11769874
Oct 7, 2026engine
While driving down interstate noticed drop in oil pressure and immediately a noise in engine with loss of power. Immediately took it to dealership and they diagnosed rod bearing failure. GM refuses to pay for engine.
NHTSA complaint #11769499
Oct 5, 2026engine
My 2020 GMC Sierra 1500 slt with the 6.2l l87 engine experienced complete engine failure at approximately 129,000 miles. The vehicle is currently at trent cadillac GMC in new bern, nc and is available for inspection upon request. The dealer confirmed the engine requires replacement along with timing-chain-related repairs, estimated at approximately $11,000. Before the failure,… Read more
My 2020 GMC Sierra 1500 slt with the 6.2l l87 engine experienced complete engine failure at approximately 129,000 miles. The vehicle is currently at trent cadillac GMC in new bern, nc and is available for inspection upon request. The dealer confirmed the engine requires replacement along with timing-chain-related repairs, estimated at approximately $11,000. Before the failure, I had previously reported concerns involving oil pressure/engine operation to a chevrolet dealer. At one visit, the dealer documented that it could not duplicate the oil-pressure concern. The vehicle was later serviced again, but the problem ultimately progressed to complete engine failure. When the truck arrived at trent after the failure, no oil registered on the dipstick. This presents a safety concern because sudden engine failure and loss of power can leave a driver unable to maintain normal vehicle operation or safely exit traffic, particularly at highway speeds. After the failure, the truck was evaluated by big boys in grimesland, nc and then towed to trent cadillac GMC for authorized GM dealer diagnosis. GM customer care has also reviewed my case. I am concerned this failure may be related to known failure patterns involving GM 6.2l l87 engines and internal engine components. Although my 2020 model is outside the current recall population, it experienced complete engine failure after earlier oil-pressure concerns. I am requesting this failure be documented and evaluated as a potential safety def
NHTSA complaint #11768916
Oct 2, 2026engine and engine cooling, engine
The contact owns a 2020 GMC Sierra 1500. The contact stated that while driving 74 MPH, the vehicle made a loud banging sound, reduced engine power, and was losing oil pressure. The dealer associated the failure with NHTSA action number: ea25007 (engine, engine and engine cooling). The dealer was contacted and the vehicle was diagnosed with rod bearing failure. The… Read more
The contact owns a 2020 GMC Sierra 1500. The contact stated that while driving 74 MPH, the vehicle made a loud banging sound, reduced engine power, and was losing oil pressure. The dealer associated the failure with NHTSA action number: ea25007 (engine, engine and engine cooling). The dealer was contacted and the vehicle was diagnosed with rod bearing failure. The manufacturer was contacted by phone and made aware of the failure. The failure mileage was approximately 124,000.
NHTSA complaint #11768586
Sep 30, 2026engine
The engine blew up driving down the road 5k miles past warranty. Complete junk and had to pay for a new one. They would only put in another defective 6.2 GMC engine and it will fail again
NHTSA complaint #11768156
Sep 28, 2026electrical system, engine
6 months after owning it the lifters went bad got them fixed then they immediately went bad again also bent rods then a day after getting that fixed again the oil pump went bad it was issue after issue
NHTSA complaint #11767573
Sep 24, 2026engine
While slowly accelerating from a stop, with 4 family members in the truck, the engine began to run rough for about 1-2 seconds then multiple notifications flashed across the dashboard (check engine, steering assist is reduced-drive with care, service ESC, and service parking brake). The road we were on was steep and twisty and did not have room to pull over which put us in an… Read more
While slowly accelerating from a stop, with 4 family members in the truck, the engine began to run rough for about 1-2 seconds then multiple notifications flashed across the dashboard (check engine, steering assist is reduced-drive with care, service ESC, and service parking brake). The road we were on was steep and twisty and did not have room to pull over which put us in an unsafe position with compromised steering and no shoulder. We made it 2 miles home but there was smoke coming from the exhaust and the engine ran very rough. Truck was towed to my mechanic. Mechanic confirmed issue. Diagnosis was misfire in #5 cylinder, confirmed initial compression upon startup (1 second) then compression loss and cylinder full of oil due to failed lifter. No previous issues prior to failure.
NHTSA complaint #11766668
Sep 19, 2026unknown or other, engine, fuel/propulsion system
Vehicle: 2020 GMC Sierra 1500 slt VIN: 3gtu9del5lg340438 engine: 6.2l v8, rpo l87 mileage: approximately 129,854 miles my 2020 GMC Sierra 1500 equipped with the l87 6.2l v8 experienced an engine failure and has been diagnosed as needing an engine replacement. I am reporting this because my vehicle is equipped with the same l87 6.2l engine currently being investigated by NHTSA… Read more
Vehicle: 2020 GMC Sierra 1500 slt VIN: 3gtu9del5lg340438 engine: 6.2l v8, rpo l87 mileage: approximately 129,854 miles my 2020 GMC Sierra 1500 equipped with the l87 6.2l v8 experienced an engine failure and has been diagnosed as needing an engine replacement. I am reporting this because my vehicle is equipped with the same l87 6.2l engine currently being investigated by NHTSA under engineering analysis ea25007 for engine failures occurring outside the scope of recall 25v-274. My model year is not currently included in recall 25v-274. However, ea25007 specifically addresses l87 engine failures occurring outside the existing recall population, including 2019–2024 GMC Sierra 1500 vehicles. GM also issued preliminary information bulletin pip5900, “diagnostic tips for seized engine or engine noise,” applicable to 2019–2023 GMC sierra vehicles equipped with the 6.2l l87 engine, which identifies possible crankshaft bearing failure. I am requesting that this engine failure be documented as part of NHTSA's ongoing investigation of l87 engine failures outside recall 25v-274.
NHTSA complaint #11765481
Sep 15, 2026engine
Timing in engine is going out at 150,000 miles
NHTSA complaint #11764385
Sep 15, 2026power train, electrical system, engine
5/5/25 woke up back seat entire truck flooring soaking wet back glass cracked. 4/8/25 transmission went out 117,000 miles 7/3/25 exhaust leak and placed nox 1. 7/8/25 127551 mileage exhaust leak replace gaskets, belt , tensioner, and pulley, 6/8/2025 3 knock sensors replaced and replaced intake manifold.
NHTSA complaint #11764362
Sep 14, 2026engine and engine cooling
The contact owns a 2020 GMC Sierra 1500. The contact stated that while driving approximately 55 MPH, the vehicle started losing power and decelerated. The check engine warning light was flashing with several unknown messages displayed. The vehicle was parked on the side of the road and later towed to the local dealer to be diagnosed. The contact was informed that the lifters,… Read more
The contact owns a 2020 GMC Sierra 1500. The contact stated that while driving approximately 55 MPH, the vehicle started losing power and decelerated. The check engine warning light was flashing with several unknown messages displayed. The vehicle was parked on the side of the road and later towed to the local dealer to be diagnosed. The contact was informed that the lifters, push rods, and camshaft had failed and needed to be replaced. The lifters, push rods, and camshaft were replaced, and the vehicle was repaired. The contact stated that approximately 6,900 miles later, the failure reoccurred. The vehicle was towed back to the local dealer, and the contact was informed that the engine crankshaft and connecting rods had failed and the engine needed to be replaced. The vehicle was not yet repaired. The failure mileage was 115,000.
NHTSA complaint #11764134
Sep 9, 2026power train, engine
Powertrain issues and a chassis issue that is extremely dangerous.tailgate on rare occasions falls open by itself. There is a design flaw in the placement of the catalytic converters. The heat is burning up the fluid. I could not believe my eyes when I serviced the transmission. This is another shortcut by GM to save on the extra wiring needed for the oxygen sensors (2)in the… Read more
Powertrain issues and a chassis issue that is extremely dangerous.tailgate on rare occasions falls open by itself. There is a design flaw in the placement of the catalytic converters. The heat is burning up the fluid. I could not believe my eyes when I serviced the transmission. This is another shortcut by GM to save on the extra wiring needed for the oxygen sensors (2)in the converters and the two oxygen sensors downstream of the converters. There is plenty of room for the converters further down by the tail shaft to drive shaft connections. This is GM’s way of being cheap. Here’s the problem. The converters get way too hot. The fill plug for the transmission which is behind a low rent heat shield crumbled into my hands from excessive heat buildup. GM knows there is a problem with the fluid breaking down. Their bandaid answer is to use mobil 1 fluid instead of the recommended dexron 6. What needs to happen is a safety recall issued for the unwanted tailgate deploying all by itself. There needs to be a redesign in the exhaust system. The transmission (8 speed) has a catalytic converter exactly on both sides and the crossover pipe runs directly under the transmission sump pan. No wonder they are having issues with transmissions burning up. This is a fire hazard !!! With the converters being so close to the exhaust manifolds, a leak from the engine or the transmission would be enough to ignite and possibly kill the occupants. All in the name of saving a few cents in wiring. My
NHTSA complaint #11763015
Sep 9, 2026engine
I was driving home with my wife. The engine just cut off. No power to the gas pedal. Luckily we were able to coast long enough to find a shoulder to pull off onto. Truck wouldn’t restart. Had to call a tow truck and have it towed to the chevy dealership. The engine was already repaired once. Ref number 11696129. I just got the truck back and fixed again. So far I’ve had… Read more
I was driving home with my wife. The engine just cut off. No power to the gas pedal. Luckily we were able to coast long enough to find a shoulder to pull off onto. Truck wouldn’t restart. Had to call a tow truck and have it towed to the chevy dealership. The engine was already repaired once. Ref number 11696129. I just got the truck back and fixed again. So far I’ve had to pay for 2 tows and 2 repairs costing be about 3000 dollars. Both repairs have been done at a chevy dealership.
NHTSA complaint #11763011
Sep 8, 2026engine
I was driving on the highway at 70mph when out of no where my truck stopped running and I received a message warning to put the truck in neutral and restart the engine. It was very alarming being on the highway and this happening. I was unable to restart the vehicle so I had to coast and navigate us at high speed to the should of the highway. Since it was labor day I had to… Read more
I was driving on the highway at 70mph when out of no where my truck stopped running and I received a message warning to put the truck in neutral and restart the engine. It was very alarming being on the highway and this happening. I was unable to restart the vehicle so I had to coast and navigate us at high speed to the should of the highway. Since it was labor day I had to sit for over 4 hours before getting a tow vehicle at 2am to tow my truck to [xxx] flow buick GMC. They contacted me and told me that my engine had seized and that it was possible bearings or something that made it seize and I need a whole new engine. They quoted me 12,500. I have not done anything yet in repairs and I now contacted GM and submitted a case #xxx. I notified them I am aware of the known issue and the GM service bulletin pip5900. I am waiting for them to respond now. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
NHTSA complaint #11762788
Sep 7, 2026service brakes, engine
Lifter failed due to afm system. Cyl 8 misfire due to oil fouling. The onboard computer got confused and would not release the parking brake until repeated attemtps to release it. 5.3l v8 2020 model year 115250 miles. Isn't this the same problem as the 2021 and newer engines? 8spd transmission. Afm failure. 9k repair.
NHTSA complaint #11762548
Sep 3, 2026engine
2020 GMC Sierra 1500 at4, 3.0l lm2 duramax. In service 08/13/2020. Five glow plug failures on five different cylinders in under 19,000 miles, all at one GM dealer, all part 24000504: cyl 1, 10/21/2024, 38,650 mi, p0671, ro 13714, warranty. Cyl 6, 11/05/2024, 38,793 mi, p1330, ro 26665, warranty. Cyl 4, 11/29/2024, 39,683 mi, p133b, ro 57498, warranty. Cyl 3, 01/22/2026,… Read more
2020 GMC Sierra 1500 at4, 3.0l lm2 duramax. In service 08/13/2020. Five glow plug failures on five different cylinders in under 19,000 miles, all at one GM dealer, all part 24000504: cyl 1, 10/21/2024, 38,650 mi, p0671, ro 13714, warranty. Cyl 6, 11/05/2024, 38,793 mi, p1330, ro 26665, warranty. Cyl 4, 11/29/2024, 39,683 mi, p133b, ro 57498, warranty. Cyl 3, 01/22/2026, 52,959 mi, p0673/p06c7/p133a, ro 100951, I paid $713.38. Cyl 2, 08/26/2026, 57,466 mi, p06c6/p0672/p1339, ro 115953, GM under n232430460. The first three came within 39 days and 1,033 miles. Every ro documents the same finding: high internal resistance in the plug, circuit tests good. The failure is internal to the plug. Glow plug failure on a diesel causes hard starting, extended cranking, no-start in cold weather, and startup misfire - risk of being stranded or unable to start. GM has documented this defect three times: pip5762 (12/2020), tsb 22-na-027 (2/2022), special coverage n232430460 (1/2024). All name an inadequate camshaft housing cover baffle plate weld, and all limit the remedy to cylinder 2. On the recorded walkaround for ro 115953 the tech stated my engine serial falls inside the affected population and my earlier failures were probably the same condition. GM replaced only the glow plug. The camshaft cover GM identifies as the cause is still installed; GM quoted me $5,100 to replace it at my expense. Four of five failures were on cylinders 1, 3, 4 and 6, outside that scope. If the bad weld p
NHTSA complaint #11762016
Aug 29, 2026engine
Driving approximately 75mph on a local highway, my engine shut down with no warning, the screen said to shift into neutral to restart but nothing happened so I was stranded along the side of the highway and had to wait 2hrs for a tow truck in the middle of the night and the engine is currently locked up.
NHTSA complaint #11760597
Aug 26, 2026engine
Misfire on 2 cylinder, noise on start up diagnostic code p0300 p0302 p050 I was driving home and the engine started making a strange sound, vehicle would could no increase speed normally. The dealership did basic analysis from the onboard computer and did a compression test. Heavy knocking sound on passenger side of the engine. The issue happened on aug 5th 2026. The… Read more
Misfire on 2 cylinder, noise on start up diagnostic code p0300 p0302 p050 I was driving home and the engine started making a strange sound, vehicle would could no increase speed normally. The dealership did basic analysis from the onboard computer and did a compression test. Heavy knocking sound on passenger side of the engine. The issue happened on aug 5th 2026. The issue is due to the afm that causes the lifter to fail and dealership says I need a new engine $15787 or replace cam shaft $14530.
NHTSA complaint #11759795
Aug 26, 2026engine
On xxx my GMC 6.2l Sierra 1500 denali engine cutoff in traffic and had to be towed. There was no indications prior to failure. Found out after replacing battery that the 400amp fuse blew and the engine seized. Vehicle was then towed to hendrick buick GMC dealer in [xxx] for repair. My engine has 49,500 miles but is out of warranty due to time. Information redacted… Read more
On xxx my GMC 6.2l Sierra 1500 denali engine cutoff in traffic and had to be towed. There was no indications prior to failure. Found out after replacing battery that the 400amp fuse blew and the engine seized. Vehicle was then towed to hendrick buick GMC dealer in [xxx] for repair. My engine has 49,500 miles but is out of warranty due to time. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
NHTSA complaint #11759731
Aug 26, 2026power train, engine
High pressure fuel pump went at 80k and now on my 2nd transmission under 100k miles this is absolutely absurd
NHTSA complaint #11759608
Aug 25, 2026engine
Engine went into limp mode and engine is no longer good
NHTSA complaint #11759601
Aug 24, 2026power train, engine
The 5.3l engine active fuel management failure problem. This known problem with the GMC motors was not disclosed by any dealerships or the manufacturer. While driving down the roadway, the truck had an engine malfunction and I was fortunate enough to be able to safely pull over. The check engine light activated and I took it to the dealer the next day. I was informed by the… Read more
The 5.3l engine active fuel management failure problem. This known problem with the GMC motors was not disclosed by any dealerships or the manufacturer. While driving down the roadway, the truck had an engine malfunction and I was fortunate enough to be able to safely pull over. The check engine light activated and I took it to the dealer the next day. I was informed by the dealer that this was a known, common issue that GM was aware of but was not offering assistance. I had to pay $11,000 out-of-pocket because of this.
NHTSA complaint #11759295
Aug 24, 2026engine, back over preventionCrash
Piston 5 dropped compression to 120 the rest were 190-200. The engine failed therefore none of my parking assist sensors were working and I backed into a car because the truck was misfiring.
NHTSA complaint #11759264
Aug 24, 2026power train, electrical system, engine
Our 2020 GMC Sierra 1500 has suffered catastrophic systems and engine failure including the brakes multiple times for almost 4 years. It has happened in high traffic and on the interstate each time having to be coasted off of the road to come to a rolling stop. There have been nine repair attempts with GM dealers repeatedly stating the issues were repaired and returning our… Read more
Our 2020 GMC Sierra 1500 has suffered catastrophic systems and engine failure including the brakes multiple times for almost 4 years. It has happened in high traffic and on the interstate each time having to be coasted off of the road to come to a rolling stop. There have been nine repair attempts with GM dealers repeatedly stating the issues were repaired and returning our vehicle to us. We began making the ceo and executive team aware of the potentially deadly safety hazards including the fact that I, [xxx] am disabled and power wheelchair dependent requiring a truck that can carry my power wheelchair. We have sent numerous emails to ms. [xxx] and the executive team numerous times informing them in detail, each time, of all issues involved. We started communicating via phone and email with customer care to no avail. All attempts at repair finally ended in complete engine failure leaving us with an estimate to replace the engine of over $13,000. We have also, submitted a detailed complaint to the attorney general’s office and after review were given the case # tcp - xxx. I will attach the complaint and addendum sent to the attorney general along with two of the emails sent to ms. [xxx] and her team informing her of all issues with the truck. They took no action to actually help us get this truck off of the road knowing it was having catastrophic engine and system failure and that it had to be driven to transport a disabled power wheel dependent with severe medical iss
NHTSA complaint #11759239
Aug 24, 2026engine
I purchased my 2020 GMC Sierra 1500 at4 with the l87 6.2l v8 new from a GMC dealer in march 2020 for $65,910 (VIN [xxx]). The truck has primarily highway mileage, very little towing, and has been well maintained. At 166,634 miles on [xxx], the truck developed a flashing check-engine light. The GMC dealer diagnosed “cyl 3 lifter failure with camshaft damage” and determined that… Read more
I purchased my 2020 GMC Sierra 1500 at4 with the l87 6.2l v8 new from a GMC dealer in march 2020 for $65,910 (VIN [xxx]). The truck has primarily highway mileage, very little towing, and has been well maintained. At 166,634 miles on [xxx], the truck developed a flashing check-engine light. The GMC dealer diagnosed “cyl 3 lifter failure with camshaft damage” and determined that replacing the engine was preferable to repairing it because of the vehicle's mileage. The dealer installed a replacement oem GMC engine and replaced both broken engine mounts. The replacement engine and installation cost $11,778. The replacement engine has subsequently required multiple repairs. At approximately 170,411 miles, the GMC dealer documented an exhaust leak that had occurred since the engine repair and a coolant leak from the upper radiator hose; both were repaired. At approximately 187,699 miles, the truck experienced overheating, coolant leakage, and loud engine-area noise. The dealer found that the water pump was coming apart and replaced the water pump and related components. I am reporting this vehicle because it is a 2020 sierra equipped with the l87 6.2l engine and experienced catastrophic lifter/camshaft failure requiring complete engine replacement, followed by multiple engine-related repairs. I believe this history is relevant to NHTSA's investigation of l87 engine failures in earlier model years and warrants consideration when evaluating whether the known l87 engine defect exten
NHTSA complaint #11759035
Aug 11, 2026engine
I was driving doing about 60 MPH. All of a sudden the engine stopped and the truck just coasted. I was able to find a safe spot on the side of the road and pull over. Called a tow truck and had it taken to the GM dealership nearby. The trucks engine was just fixed in october of 2025 for the camshaft and lifter rods. It’s currently in the shop and I’m waiting for the diagnostics.
NHTSA complaint #11756301
Aug 6, 2026power train, engine
"while driving, the vehicle suddenly experienced a flashing check engine light, an electronic stability control (ESC) warning light, and violent steering wheel vibrations. The vehicle suffered a severe loss of power and misfired, creating an immediate traffic hazard. The dealership diagnosed the issue as a catastrophic mechanical lifter failure on the 5.3l v8 ecotec engine… Read more
"while driving, the vehicle suddenly experienced a flashing check engine light, an electronic stability control (ESC) warning light, and violent steering wheel vibrations. The vehicle suffered a severe loss of power and misfired, creating an immediate traffic hazard. The dealership diagnosed the issue as a catastrophic mechanical lifter failure on the 5.3l v8 ecotec engine with dynamic fuel management (dfm). Despite the dealer replacing an entire bank of lifters, the engine continues to misfire and vibrate. This premature valvetrain failure at only 36,000 miles is a known design defect that causes sudden engine stalling and disables critical safety features like stability control while the vehicle is in motion, presenting a severe crash risk."
NHTSA complaint #11755269
Aug 4, 2026engine
The truck starting making a ticking noise within 24 hours the check engine light was on and it starting shuttering. I got it to the dealership were they informed me of lifters failure, and catastrophic engine failure. Dealer is recommending replacing engine since it's a 2020 and not part of recall.
NHTSA complaint #11754824
Aug 3, 2026engine
I brought my truck into a certified GM dealer for recall work on the ground strap. I left the dealership and multiple lights came on dash: check engine light, service ecs, traction control, service parking brake, steering assist reduced. 7 minutes later the engine began miss firing. The dealer asked me to bring it back to the shop and after some digging they discovered my l87,… Read more
I brought my truck into a certified GM dealer for recall work on the ground strap. I left the dealership and multiple lights came on dash: check engine light, service ecs, traction control, service parking brake, steering assist reduced. 7 minutes later the engine began miss firing. The dealer asked me to bring it back to the shop and after some digging they discovered my l87, 6.2 engine was missing firing in cylinder 5. Now the motor needs to be replaced and GM is not standing behind the repair.
NHTSA complaint #11754382
Jul 17, 2026service brakes, engine
The contact’s mother-in-law owns a 2020 GMC Sierra 1500. The contact stated that while her brother-in-law was starting the vehicle, the brake, service engine, and engine warning lights illuminated and the vehicle failed to start. The contact stated that the failure was associated with NHTSA action number: ea25007 (engine, engine, and engine cooling) and pe25001 (engine,… Read more
The contact’s mother-in-law owns a 2020 GMC Sierra 1500. The contact stated that while her brother-in-law was starting the vehicle, the brake, service engine, and engine warning lights illuminated and the vehicle failed to start. The contact stated that the failure was associated with NHTSA action number: ea25007 (engine, engine, and engine cooling) and pe25001 (engine, engine, and engine cooling). The vehicle was towed to a local dealer, where it was diagnosed with engine failure. The vehicle was not repaired. The owner was scheduled to meet with the dealer to discuss the issue. The manufacturer was contacted and confirmed that there were no open recalls on the VIN related to the failure. The failure mileage was approximately 45,000.
NHTSA complaint #11751171
Jul 8, 2026engine and engine cooling
The contact owns a 2020 GMC Sierra 1500. The contact stated that while accelerating from a complete stop on several occasions, an abnormal clicking sound was heard from the engine compartment. The vehicle was taken to the dealer, where it was diagnosed with a failed fan belt pulley. The vehicle was not repaired. Additionally, while parked on one occasion, an abnormal clicking… Read more
The contact owns a 2020 GMC Sierra 1500. The contact stated that while accelerating from a complete stop on several occasions, an abnormal clicking sound was heard from the engine compartment. The vehicle was taken to the dealer, where it was diagnosed with a failed fan belt pulley. The vehicle was not repaired. Additionally, while parked on one occasion, an abnormal clicking sound and a loud bang were heard from the engine compartment, and the vehicle stalled. The contact attempted to restart the vehicle, but it failed to turn over. The vehicle was taken to the dealer, where a failed valve spring was diagnosed. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 75,127.
NHTSA complaint #11749070
Jul 6, 2026engine
The cam shaft bearing failed under normal driving conditions. Many of the service engine lights including brakes and primary service engine light came on after the cam shaft bearing failure. The engine was replaced by a GM dealership at 65,000 miles and was inspected to determine the cam shaft bearing failed. Luckily the engine failed at a speed of 35 MPH on an off ramp, as a… Read more
The cam shaft bearing failed under normal driving conditions. Many of the service engine lights including brakes and primary service engine light came on after the cam shaft bearing failure. The engine was replaced by a GM dealership at 65,000 miles and was inspected to determine the cam shaft bearing failed. Luckily the engine failed at a speed of 35 MPH on an off ramp, as a complete engine failure on the highway could have been much more dangerous. Following the replacement of the engine, within 500 engine miles, o2 sensors in the catalytic converter were replaced and ultimately the catalytic converter had to be replaced as well.
NHTSA complaint #11748595