Nov 13, 2026engineCrash
2018 GMC Sierra 1500 with an l86 engine experienced a lifter failure and subsequent engine failure at 68,775 miles. The dealer where I purchased the vehicle new has the confirmed the diagnosis of a lifter failure and subsequent engine failure needing replacement and is awaiting repair. This failure could have caused a crash, fire or personal injury. After freeway driving, the… Read more
2018 GMC Sierra 1500 with an l86 engine experienced a lifter failure and subsequent engine failure at 68,775 miles. The dealer where I purchased the vehicle new has the confirmed the diagnosis of a lifter failure and subsequent engine failure needing replacement and is awaiting repair. This failure could have caused a crash, fire or personal injury. After freeway driving, the engine switched to active fuel management mode, made a rather large bang and displayed the flashing check engine light and a solid traction light. The vehicle was taken to the dealer where I had purchased it for diagnosis.
NHTSA complaint #11777823
Nov 7, 2026engine
NHTSA vehicle safety defect complaint vehicle: 2018 GMC Sierra 1500, 4wd crew cab engine: 5.3l v8 with active fuel management (afm) VIN: [xxx] manufacturer: general motors component: engine and engine cooling / powertrain. Date of most recent failure: xxx. Mileage at most recent failure: 115,215 miles description of safety defect I am submitting this formal safety complaint… Read more
NHTSA vehicle safety defect complaint vehicle: 2018 GMC Sierra 1500, 4wd crew cab engine: 5.3l v8 with active fuel management (afm) VIN: [xxx] manufacturer: general motors component: engine and engine cooling / powertrain. Date of most recent failure: xxx. Mileage at most recent failure: 115,215 miles description of safety defect I am submitting this formal safety complaint concerning two documented lifter-related engine failures in my 2018 GMC Sierra 1500 equipped with the 5.3l v8 engine. These failures occurred approximately four and a half years and 66,962 miles apart. First engine failure — xxx at approximately 48,253 miles, my vehicle developed an engine vibration and cylinder 3 misfire. Huston chevrolet in [xxx], diagnosed a failed lifter that had damaged the camshaft. The dealership replaced the camshaft, lifters, valve lifter oil manifold, and associated components under warranty. The repair was completed xxx. Early warning signs — xxx on xxx, at approximately 114,507 miles, huston chevrolet performed maintenance, including spark plug and wire replacement. The dealership’s service documentation states that a slight engine misfire or abnormal idle was detected before the repairs were performed. I dispute having been verbally notified of this condition or advised to pursue additional engine diagnostics. During the following weeks, my vehicle continued experiencing abnormal vibration, shaking, and hesitation. Safety concerns while driving I experienced shaking, hesi
NHTSA complaint #11776416
Sep 21, 2026engine
Customer states: thinks crankshaft pulley is loose due to prior water pump replacement-crackshaft pulley has nothing to do with water pump replacement. Before inspecting/starting engine verified oil level-oil level is on full mark. Started engine-loud rattling/knocking noise from engine-engine has internal failure-engine replacement is required. Also hearing noise in… Read more
Customer states: thinks crankshaft pulley is loose due to prior water pump replacement-crackshaft pulley has nothing to do with water pump replacement. Before inspecting/starting engine verified oil level-oil level is on full mark. Started engine-loud rattling/knocking noise from engine-engine has internal failure-engine replacement is required. Also hearing noise in rearend-cannot test drive due to engine condition several tsb's on engine failures with 6.2l engines. GM has possible recalls coming on 2019-2024 yr models. Not sure if earlier models maybe included underhood inspection 1 7003186 06ns 52.50 52.50 lbr-disc cust sat
NHTSA complaint #11765804
Sep 21, 2026engine
I was backing out of my garage and truck made strange noise and shut off . Tried to restart but just made ding and wouldn't turn over . Dash lights went blank. Had vehicle towed to shop and mechanic stated it was crank and connecting rods after he dropped the oil pan. I ordered new oem engine and waiting on delivery . Been 5 weeks now since order . Vehicle only has 106,000… Read more
I was backing out of my garage and truck made strange noise and shut off . Tried to restart but just made ding and wouldn't turn over . Dash lights went blank. Had vehicle towed to shop and mechanic stated it was crank and connecting rods after he dropped the oil pan. I ordered new oem engine and waiting on delivery . Been 5 weeks now since order . Vehicle only has 106,000 miles on it and have had it since 20,000 miles and all maintenance has always been done . Engine can be inspected at shop as new engine has not arrived
NHTSA complaint #11765772
Sep 6, 2026power train, engine
I own a 2018 GMC Sierra 1500 v8 5.3 liter which is at 46, 433 miles. Over the past few weeks I have noticed the transmission having difficulty shifting in first gear and lurching, and making shuddering noises, and as well making a constant ticking noise. After an experienced mechanic had put a diagnostic system onto my truck, his system diagnosed a transmission lifter failure,… Read more
I own a 2018 GMC Sierra 1500 v8 5.3 liter which is at 46, 433 miles. Over the past few weeks I have noticed the transmission having difficulty shifting in first gear and lurching, and making shuddering noises, and as well making a constant ticking noise. After an experienced mechanic had put a diagnostic system onto my truck, his system diagnosed a transmission lifter failure, specifically 2 out of the 8 lifters. A few days later (9-04-26) I took my truck to a certified GMC servicing business (patriot chevrolet of hopkinsville ky 270-886-1207) and had a transmission servicing done. I had told the customer service representative amanda williams about the ticking and that I thought 2 lifters going bad in the transmission were the source of it. 3 hours later the servicing was done which cost 474.43. She did not know if the ticking had stopped or not. I started my engine to head home and the ticking was still happening. Nothing had changed. I got home, parked and have not started the engine since to minimize any further damage. I have become aware that this year, make and model has become infamous for the engine/transmission design and parts failure which has been at the center of thousands of class action lawsuits. I have owned this vehicle since inheriting it from my late father for 2 months before he developed dementia and suffered a broken hip. I have religiously had the oil changed every three months regardless of the mileage, and this is a sealed transmission which canno
NHTSA complaint #11762401
Aug 11, 2026steering, engine
Head gasket failure and overheating. After fixed, power steering has just failed during driving. Will have to have it towed to shop
NHTSA complaint #11756121
Jul 31, 2026engine, forward collision avoidance
Engine failure, 5/3/22, 23,987 miles, all lifters was replaced under warranty, engine failure, 7/6/26, 46004 miles, took truck in for oil change and when returned had a ticking noise. Dealership notified me that camshaft issues and metal detected in oil. Engine needs replaced. 6.2 v8 2018. Turpin motors, geneseo, il has done all serivce on truck. No warning lights or codes.… Read more
Engine failure, 5/3/22, 23,987 miles, all lifters was replaced under warranty, engine failure, 7/6/26, 46004 miles, took truck in for oil change and when returned had a ticking noise. Dealership notified me that camshaft issues and metal detected in oil. Engine needs replaced. 6.2 v8 2018. Turpin motors, geneseo, il has done all serivce on truck. No warning lights or codes. Vehicle is in my garage and available for inspection. I opened case with GM #105652237. Dealership opened case on GM portal also. Response from GM is that truck is out of warranty
NHTSA complaint #11754023
Jun 11, 2026power train, engine
Vehicle details: 2018 GMC Sierra 1500 z72 4x4, 5.3l v8 ecotec3 engine, VIN: [xxx] mileage at time of incident: 220,000 miles location: [e.g., little rock, arkansas area or specific road/highway – please provide if desired] what happened: the 5.3l v8 engine’s hydraulic roller lifters failed. One or more lifters collapsed, stuck, or lost proper oil pressure/operation. This LED… Read more
Vehicle details: 2018 GMC Sierra 1500 z72 4x4, 5.3l v8 ecotec3 engine, VIN: [xxx] mileage at time of incident: 220,000 miles location: [e.g., little rock, arkansas area or specific road/highway – please provide if desired] what happened: the 5.3l v8 engine’s hydraulic roller lifters failed. One or more lifters collapsed, stuck, or lost proper oil pressure/operation. This LED to improper valvetrain function, causing loud ticking/knocking noises, cylinder misfires, significant loss of engine power and performance, and internal engine damage (such as camshaft lobe wear or related components). Component or system that failed or malfunctioned: hydraulic valve lifters (camshaft followers) in the engine valvetrain, associated with the active fuel management (afm) system. The failed lifter(s) and related components are available for inspection upon request. How safety was put at risk: the engine malfunction resulted in sudden or progressive power loss and misfiring while driving. This reduced the vehicle’s ability to accelerate or maintain speed, especially in traffic or on highways, creating a hazardous situation that put my safety and the safety of other road users at risk of collision or breakdown. No accident or injuries occurred , or other symptoms prior to the failure with details recall, e.g., ticking noise timeline, misfires has the problem been reproduced or confirmed by a dealer or independent service center? “yes, confirmed by shop inspection” has the vehicle or compon
NHTSA complaint #11743611
Jun 2, 2026steering, service brakes, engine
Incident description: on three occasion I have had the same catastrophic engine failure putting myself and my family along with the general public in harms way. Starting march of 2022 while driving at approximately 60 MPH on the west shore expressway my truck experienced a sudden and total loss of motor power. My engine stalled out and I lost my ability to safety steer and… Read more
Incident description: on three occasion I have had the same catastrophic engine failure putting myself and my family along with the general public in harms way. Starting march of 2022 while driving at approximately 60 MPH on the west shore expressway my truck experienced a sudden and total loss of motor power. My engine stalled out and I lost my ability to safety steer and stop my vehicle. This all happened during rush hour while driving in the left lane of traffic. This sudden loss of power forced me to maneuver the vehicle to the right shoulder of the expressway across the right lane of traffic. As there was no shoulder to pull over on the left side of the highway. This created an immediate crash risk for myself and other drivers. Upon inspection at the authorized GMC dealership where I purchased the truck new, a certified mechanic determined that the engine experienced a complete failure requiring replacement or rebuilding of the engine. I paid to have the engine rebuilt at the dealership. The second instance was similar to the above incident. Once again I paid for the repair. The third instance was more dangerous as when my trucks engine failed it almost caused an accident. As of today my truck is still sitting in the dealership for over 6 months and no one from the dealership or manufacturer will give me an answer on what has to be done now. This patter of sudden repeated engine failure clearly indicates a systemic safety defect that extends beyond normal wear and
NHTSA complaint #11741547
Jan 29, 2026engine and engine cooling, engine
The contact owns a 2018 GMC Sierra 1500. While starting the vehicle, it was shaking violently, with reduced power. The vehicle was restarted and worked as designed. Upon research, the contact associated the failure with NHTSA action number: pe25001 (engine and engine and cooling). The vehicle was taken to an independent mechanic who determined there was metal in the engine,… Read more
The contact owns a 2018 GMC Sierra 1500. While starting the vehicle, it was shaking violently, with reduced power. The vehicle was restarted and worked as designed. Upon research, the contact associated the failure with NHTSA action number: pe25001 (engine and engine and cooling). The vehicle was taken to an independent mechanic who determined there was metal in the engine, and there was a misfire coming from cylinder #2. The mechanic recommended that the engine be replaced. There were loose wires from the ECM, and the failure halted after the mechanic secured the wires. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The approximate failure mileage was 150,000.
NHTSA complaint #11714207
Jan 20, 2026power train, engine
I own a 2018 GMC sierra denali ultimate, the truck has the 6.2 engine which had the lifter issue as stated with the current situation. At the time, the truck had 37,000 miles when the issues started. I purchased the truck from andy mohr with 8806 miles on it in november of 2019. I worked overseas for the dod so that’s why the miles are low. After I got it fixed, ($4500… Read more
I own a 2018 GMC sierra denali ultimate, the truck has the 6.2 engine which had the lifter issue as stated with the current situation. At the time, the truck had 37,000 miles when the issues started. I purchased the truck from andy mohr with 8806 miles on it in november of 2019. I worked overseas for the dod so that’s why the miles are low. After I got it fixed, ($4500 dollars at hare chevrolet) I experienced the transmission shake while driving home from work with my children in it. The transmission was shaking so bad the whole cab was rocking.that repair was $3,300. Now, the truck has piston slap and rod issues and currently at hare chevrolet for service. I was told I need a full rebuild ($12,000 dollars or a new engine $14000 dollars). As a retired air force veteran, I didn’t expect issues like this, especially when I baby the truck and it currently has 40,530 miles. I had regular oil changes and service, yet now stuck with a high class truck that has serious issues that seem to be ignored by GM and andy mohr GMC. Andy mohr sold me an extended warranty at time of purchase but I paid for a year and a half that wasn’t usable. If I had that warranty I would be covered now.but besides that, it’s a denali, I shouldn’t be having a new engine at 40,530 miles. I am happy that there is an investigation but it needs to be widened because my truck was right before the new model rollout but I am having the same issues. If needed, I have all my receipts and information and will provi
NHTSA complaint #11712288
Jan 19, 2026engine
The lifters in my engine collapsed. This caused a push rod to be bent and the cam shaft to be damaged causing thousands to fix. While I was driving. I could feel the engine malfunction causing my speed to significantly decrease. The vehicle was fixed through an independent mechanic. Mechanic stated that the active fuel management system is the cause for the lifter collapse. There was no warning before the failure
NHTSA complaint #11711924
Jan 6, 2026engine
Engine failure. 6.2l with afm system extreme oil consumption heavy metal in oil loud ticking 120789 miles purchase date 05/29/2025 madras, oregon chevrolet dealer
NHTSA complaint #11709032
Dec 15, 2025power train, engine
I have 125,000 miles on my truck. I was traveling with my grandkids in the back seat. We were going through a four way stop. My truck started tapping like a lifter issue. The next thing I know is the truck engine light started flashing and car started to shake. Then, my truck lost all power and a big cloud of blue smoke came out of the tail pipe. The truck could not be… Read more
I have 125,000 miles on my truck. I was traveling with my grandkids in the back seat. We were going through a four way stop. My truck started tapping like a lifter issue. The next thing I know is the truck engine light started flashing and car started to shake. Then, my truck lost all power and a big cloud of blue smoke came out of the tail pipe. The truck could not be driven any further. The symptoms: engine tapping, low oil, engine light flashing, shaking, lost all movement, and a cloud of smoke we had to tow my truck to the dealer and they are still accessing the issue. All symptoms are identical to the current recall of the GMC engines.
NHTSA complaint #11705013
Nov 20, 2025engine
The injector failure in my 2018 GMC Sierra 1500 resulted in repeated misfire conditions (p0300 and p0307), causing the vehicle to lose power unexpectedly while driving. The engine would hesitate, shake, and struggle to accelerate, especially during merging or highway speeds. These symptoms created a significant safety hazard because the vehicle could not reliably maintain… Read more
The injector failure in my 2018 GMC Sierra 1500 resulted in repeated misfire conditions (p0300 and p0307), causing the vehicle to lose power unexpectedly while driving. The engine would hesitate, shake, and struggle to accelerate, especially during merging or highway speeds. These symptoms created a significant safety hazard because the vehicle could not reliably maintain speed or respond to throttle input. Sudden power loss in traffic exposes the driver and surrounding motorists to an increased risk of collision, particularly during lane changes, freeway merging, intersection crossings, and passing maneuvers. The dealership confirmed internal injector failure, and the vehicle has been out of service for three months without resolution. This is a safety-critical defect that compromises vehicle controllability, stability, and safe operation on public roads.”
NHTSA complaint #11700630
Nov 18, 2025power train, engine
2018 GMC sierra started having shuddering/jerking/jumping problems at around 60k miles. This problem occurs while driving on straight aways, going uphill and while in drive at a stop sign/light. When the gas is accelerated the truck then hesitates and jerks/jumps. We have taken it to the GMC dealership and paid for the diagnostics and were informed “the problem wasn’t severe… Read more
2018 GMC sierra started having shuddering/jerking/jumping problems at around 60k miles. This problem occurs while driving on straight aways, going uphill and while in drive at a stop sign/light. When the gas is accelerated the truck then hesitates and jerks/jumps. We have taken it to the GMC dealership and paid for the diagnostics and were informed “the problem wasn’t severe enough”. The truck has only been serviced by GMC dealership. So after failed attempts with GMC service department we have taken it to a local small auto shop and they automatically said it was the drive train and needed to be taken to a transmission shop. We have been GM owners for decades and are so disappointed in the service received from them.
NHTSA complaint #11700188
Oct 31, 2025power train, seats, engine
I purchased a 2018 GMC Sierra 1500 6.2 denali new. I followed all service requirements including oil changes by GM dealerships. 2025 I noticed my truck power was decreasing. Than I started to hear knocking noses. I took it to a dealership for diagnosis but they couldn't identify anything. Finally it started to skip this is when a dealership diagnose it as being an issue with… Read more
I purchased a 2018 GMC Sierra 1500 6.2 denali new. I followed all service requirements including oil changes by GM dealerships. 2025 I noticed my truck power was decreasing. Than I started to hear knocking noses. I took it to a dealership for diagnosis but they couldn't identify anything. Finally it started to skip this is when a dealership diagnose it as being an issue with the active fuel management system. They said my lifters, camshaft, and various other parts was damaged and had to be replaced. Additionally, they said it was a recall on 6.2 engines with the same identical issue but my year wasn't included. The cost to repair approximately 10,000. I really need your attention to this matter! September 10, 2025 my truck placed me and others in danger when it lose engine power. Also my engine light was on for the first time.
NHTSA complaint #11696714
Oct 9, 2025engine and engine cooling
The contact owns a 2018 GMC Sierra 1500. The contact stated that while attempting to accelerate from a stoplight, the vehicle hesitated before accelerating. A day later, the failure reoccurred, and the rpms increased before the vehicle accelerated. There were no warning lights illuminated. The vehicle was taken to the dealer, who diagnosed that the connecting rod had failed,… Read more
The contact owns a 2018 GMC Sierra 1500. The contact stated that while attempting to accelerate from a stoplight, the vehicle hesitated before accelerating. A day later, the failure reoccurred, and the rpms increased before the vehicle accelerated. There were no warning lights illuminated. The vehicle was taken to the dealer, who diagnosed that the connecting rod had failed, and there were metal shavings inside the engine. The contact was informed that the engine needed to be replaced. The contact related the failure to NHTSA campaign number: 25v274000 (engine and engine cooling); however, the VIN was not included. The vehicle was not repaired. The manufacturer was informed of the failure and confirmed that there was no recall on the VIN. The manufacturer opened a case for the failure. The manufacturer referred the contact to the NHTSA hotline to report the failure. The failure mileage was approximately 169,000.
NHTSA complaint #11692321
Aug 19, 2025engine
The contact owns a 2018 GMC Sierra 1500. The contact stated that while driving on a neighborhood road at 40 MPH, the check engine warning light was flashing with an abnormal knocking sound coming from the engine, and the vehicle was vibrating abnormally. The contact pulled over and used a diagnostic scanner to perform a diagnostic test on the vehicle. The scanner retrieved… Read more
The contact owns a 2018 GMC Sierra 1500. The contact stated that while driving on a neighborhood road at 40 MPH, the check engine warning light was flashing with an abnormal knocking sound coming from the engine, and the vehicle was vibrating abnormally. The contact pulled over and used a diagnostic scanner to perform a diagnostic test on the vehicle. The scanner retrieved dtc: p0301 (cylinder #1 misfire). The vehicle was towed to a local dealer to be diagnosed, and the contact was informed that the lifters, pushrods, camshaft, sparkplugs, and oil pump were faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 111,000.
NHTSA complaint #11681723
Aug 11, 2025engine and engine cooling
The contact owns a 2018 GMC Sierra 1500. The contact stated that while driving at various speeds, there was an abnormal banging sound coming from the vehicle. There was no warning light illuminated. The contact inspected fluids but found no defects with the vehicle. The vehicle was then taken to an independent mechanic, where the mechanic discovered that the lifters and cam… Read more
The contact owns a 2018 GMC Sierra 1500. The contact stated that while driving at various speeds, there was an abnormal banging sound coming from the vehicle. There was no warning light illuminated. The contact inspected fluids but found no defects with the vehicle. The vehicle was then taken to an independent mechanic, where the mechanic discovered that the lifters and cam shaft were defective. Due to the failure, the engine was replaced. The contact stated that recently, the abnormal tapping sound returned. The vehicle was taken back to the independent mechanic, who confirmed that the failure with the lifters had returned. The vehicle was taken to a dealer who confirmed the lifter failure, and the contact was provided an estimate for the repair. The manufacturer was notified of the failure, and the contact was provided a case number. The contact was then referred to the NHTSA to report the failure. The vehicle was not yet repaired. The failure mileage was approximately 90,000.
NHTSA complaint #11679813
Aug 7, 2025engine
Radiator cracked along outer edges. Similar to previous tsb’s as released by GM, but my vehicle doesn’t fall under the years covered by that tsb
NHTSA complaint #11678969
Aug 6, 2025steering, electrical system, engine
2018 GMC sierra slt's electric power steering suddenly stopped working, I almost got killed this issue has been reported by other owners
NHTSA complaint #11678809
Jul 19, 2025power train, engine, fuel/propulsion system
I own a $35,000 2018 GMC Sierra 1500 6.2l v8 4x4 denali, which is currently down due to engine failure while I was driving down the road.. Never had a check engine light on the dash. Haven't had the truck a year before it quit. Rods knocking, crankshaft bearings, loss of power, high rpm with little acceleration. I could have the peddle down to the floor and would barely get to… Read more
I own a $35,000 2018 GMC Sierra 1500 6.2l v8 4x4 denali, which is currently down due to engine failure while I was driving down the road.. Never had a check engine light on the dash. Haven't had the truck a year before it quit. Rods knocking, crankshaft bearings, loss of power, high rpm with little acceleration. I could have the peddle down to the floor and would barely get to 20 MPH.. The motor would jump so bad, you would think it's going to jump out the truck. I have replaced several parts on the truck, including oil pump, filter, solenoid valve sensor, fuel pump, injectors, and sensors, battery, starter a couple times. Did all that replacing for it to get worse and finally quit while driving.. I was stranded in the middle of the road.. Iv reported it to the recall people, but nothing helped. I have taken my vehicle to express chevrolet and they did a diagnostic test, which I provided the list they gave me below. When I took it to them, I was using endurance warranty, but they denied my claim due to the issues and they didn't cover them. At the time, the motor was still jumping, but smoke was coming out the tailpipe extremely bad, the truck was jerking and jumping. After replacing everything I listed, the truck got worse, started screeching and knocking loudly, loss of engine power, little acceleration. The day the motor quit on me while driving, I got the MPH up to about 55-60 and it just quit, and hasn't started back since.
NHTSA complaint #11674727
Jul 16, 2025engine
The contact owns a 2018 GMC Sierra 1500. The contact stated while his mother was driving 75 MPH on the highway, there was a popping and ticking sound coming from the engine, and while depressing the accelerator pedal the vehicle failed to respond. The driver was able to pull over to the right side of the road and waited for tow truck assistance. A dealer was not contacted. The… Read more
The contact owns a 2018 GMC Sierra 1500. The contact stated while his mother was driving 75 MPH on the highway, there was a popping and ticking sound coming from the engine, and while depressing the accelerator pedal the vehicle failed to respond. The driver was able to pull over to the right side of the road and waited for tow truck assistance. A dealer was not contacted. The vehicle was towed the dealer and was diagnosed and determined that the engine needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure, and informed the contact engine would take a while to be ordered. The contact was referred to the NHTSA hotline for assistance. The failure mileage was 58,000.
NHTSA complaint #11674096
Jul 2, 2025power train, engine
This 2018 GMC sierra has 100,000 miles on it and in april 2025 the transmission went out and needed a new one. Now in july 2025 the engine has lifter failure leading to the need of a new engine.
NHTSA complaint #11670689
Jun 29, 2025steering, electrical system, engine
I've had the vehicle service twice for the same incident power steering shut off in the middle of drive vehicle shuts down almost smashed into a freeway wall. This has been to the dealership numerous times to fix it and they have not. We are in the tens of thousands of dollars in repair and still nothing is fixed I've had this vehicle for 5 years it's been in the shop for at… Read more
I've had the vehicle service twice for the same incident power steering shut off in the middle of drive vehicle shuts down almost smashed into a freeway wall. This has been to the dealership numerous times to fix it and they have not. We are in the tens of thousands of dollars in repair and still nothing is fixed I've had this vehicle for 5 years it's been in the shop for at least 3 I bought it with 30000 miles it only has 61000 on it right now the last repair lasted 10000 miles this repair only lasted 4000 I almost died and was left is petrified.
NHTSA complaint #11670041
Jun 26, 2025power train, engine
Transmission has a shudder at lower speeds 1200 rmp area. Has been doing it since I bought the truck a few years ago. Took it back for warranty work and they claim this is a very common problem with this transmission. Claim that flushing the system would repair it, which it has not. Occasionally to will almost go out of gear, I have to try getting off the road safely to shut… Read more
Transmission has a shudder at lower speeds 1200 rmp area. Has been doing it since I bought the truck a few years ago. Took it back for warranty work and they claim this is a very common problem with this transmission. Claim that flushing the system would repair it, which it has not. Occasionally to will almost go out of gear, I have to try getting off the road safely to shut it off. After a few minutes, start it up and it will be back to normal. Also I’m on my 3rd starter. What appears to be another common issue with this model. Sometimes it fires right up, sometimes it’s very weak and others not at all and requires a jump start. All in all, recalls should’ve already been applied to these models. Pay way to much for junk!
NHTSA complaint #11669494
Jun 12, 2025engine and engine cooling, fuel system, gasoline
The contact owns a 2018 GMC Sierra 1500. The contact stated that while driving at an undisclosed speed and depressing the accelerator pedal, the vehicle failed to accelerate as intended. The message "reduced power" was displayed, and the rpms increased. Additionally, the vehicle jerked, and the contact noticed that there was smoke coming out of the exhaust pipe. The vehicle… Read more
The contact owns a 2018 GMC Sierra 1500. The contact stated that while driving at an undisclosed speed and depressing the accelerator pedal, the vehicle failed to accelerate as intended. The message "reduced power" was displayed, and the rpms increased. Additionally, the vehicle jerked, and the contact noticed that there was smoke coming out of the exhaust pipe. The vehicle was driven to the contact's residence. The vehicle was taken to an independent mechanic, where it was diagnosed that the starter, the battery, the fuel pump, the oil pump, the oil pump sensors, and the fuel injectors had failed and needed to be replaced. The vehicle was repaired; however, the failure reoccurred. The contact stated that while driving at an undisclosed speed, the vehicle stalled. There was no warning light illuminated. The vehicle was able to restart; however, the failure recurred. The vehicle was driven to the contact's residence. The vehicle was not repaired. The manufacturer was made aware of the failure, but no assistance was provided. The failure mileage was approximately 133,742.
NHTSA complaint #11666618
Jun 5, 2025power train, electrical system, engine
Engine lifters failed. Heard ticking noise first day truck was purchased that gradually got louder but was told by GMC service shop it was normal to hear the ticking noise. Also when cruise control is on and you are decending a hill the rpms raise and you lose engine compression this will cause your speed to drop to around 20 MPH and has happened nunerous times.. As well when… Read more
Engine lifters failed. Heard ticking noise first day truck was purchased that gradually got louder but was told by GMC service shop it was normal to hear the ticking noise. Also when cruise control is on and you are decending a hill the rpms raise and you lose engine compression this will cause your speed to drop to around 20 MPH and has happened nunerous times.. As well when making a turn sometimes or just driving the vehicle turns off while in motion and you have to coast to the side of the road and turn the key off and back on to start driving agsin.. The loss of power is a complete blackout no dash.. No engine nothing. As result of the lifter issue the engine also hard shifts in and out of slow gears.. I have not driven my truck in about a year and still owe 22k on it. The issues with this vehicle are the same as the recalled 6.3 v8 engines.
NHTSA complaint #11665102
Jun 3, 2025engine
My vehicle was a well maintained 2018 GMC Sierra 1500. It has 58000 miles. I was driving in 30 MPH zone thank god. Heard a loud boom and the truck lost power and shut off. I got out and oil was pouring out. I took it to the GMC dealership and they told me the engine failed. They didn’t know why or what caused the failure. But said they is a hole in the block and all they can say is something in the engine failed.
NHTSA complaint #11664711
May 28, 2025engine
Lifter when bad during engine start up. (known issue)
NHTSA complaint #11663349
May 14, 2025power train, engine
GM has discontinued a critical engine belt on the 2018 GMC Sierra 1500 5.3l eassist. This makes the truck undrivable and unsafe to own, even though the vehicle is still under financing and only 7 years old. There is no available part, and no alternative has been offered by the manufacturer.
NHTSA complaint #11660821
May 1, 2025steering, electrical system, engine
My engine and all electrical components including power steering and power brakes and all dashboard electrical will fail while driving. It is becoming more frequent and has almost caused an accident on numerous occasions to the point of not being able to drive safely on the highway any longer so now I only stay on surface streets and can't use for any out of town work. I… Read more
My engine and all electrical components including power steering and power brakes and all dashboard electrical will fail while driving. It is becoming more frequent and has almost caused an accident on numerous occasions to the point of not being able to drive safely on the highway any longer so now I only stay on surface streets and can't use for any out of town work. I usually do all of my own vehicle maintenance not been able to diagnose the culprit. Unfortunately I'm not able to afford the dealership diagnostic prices but open to any type of inspection.
NHTSA complaint #11658155
May 1, 2025engine
Spun main bearing in motor. Motor blown. It is available for inspection. GM mechanic inspected and quoted for new motor. Vehicle shut down going down interstate at 78 MPH. No warning.
NHTSA complaint #11658311
Apr 29, 2025power train, unknown or other, engine
I have taken it in due to engine mounts 4 different times, transmission replaced and in october 2024 I took it in for issues I was experiencing like I had before my transmission went out. I did not get my truck back until almost dec 2024 and that was due to there employee backing into the front end of my truck. So after all that my warranty was up dec 24 2024 and then on april… Read more
I have taken it in due to engine mounts 4 different times, transmission replaced and in october 2024 I took it in for issues I was experiencing like I had before my transmission went out. I did not get my truck back until almost dec 2024 and that was due to there employee backing into the front end of my truck. So after all that my warranty was up dec 24 2024 and then on april 16th 2025 I was driving my 2018 GMC sierra 6.2l 1500 denali 129,600 miles at approx 30 MPH it was late so the streets were empty and we started to hear a knocking or what I thought at the time was a very bad exhaust leak. We parked and then we started to try to make it home very slowly which we did and it was not making to much noise. The next day I called GMC and explained they said bring it in. I towed it there to be safe but it did start and still ran at very slow speed. They called me and said that the lift side rockers/ lifters 1 failed and it was stuck due to a misfire and that the engine would need to be rebuilt and sent me over some very vague break down which looked like a lump sum price. I requested and better break down and got a screen shoot and that when he said that’s the best they can do. There were no engine lights on or warnings nothing at all. It also just got serviced at GMC for an oil change on february 27th 2025 along with some air filters. Today is april 29th and still waiting for the service manage to call and see if they can do anything to help out instead of charging full price
NHTSA complaint #11657672
Mar 26, 2025engine
The contact owns a 2018 GMC Sierra 1500. The contact stated that at start-up there was an abnormal ticking sound coming from the engine. There were no warning lights illuminated. The local dealer was contacted; however, the vehicle was not diagnosed. The contact was informed that the vehicle was out of warranty, and that the VIN was not under recall. The vehicle was not… Read more
The contact owns a 2018 GMC Sierra 1500. The contact stated that at start-up there was an abnormal ticking sound coming from the engine. There were no warning lights illuminated. The local dealer was contacted; however, the vehicle was not diagnosed. The contact was informed that the vehicle was out of warranty, and that the VIN was not under recall. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 17,000.
NHTSA complaint #11650789
Mar 11, 2025engine
Lifters failed and damaged engine at 68000 miles
NHTSA complaint #11647578
Feb 26, 2025engine
Driving 70 MPH on [xxx] in moderate traffic when my vehicle suddenly slowed dramatically and began to shudder . I was in the middle lane of three westbound marked lanes and was almost hit by a driver behind me which had been following too closely. The check engine and traction control light came on and my oil gauge went to the high side. I exited onto [xxx] and at 40 MPH the… Read more
Driving 70 MPH on [xxx] in moderate traffic when my vehicle suddenly slowed dramatically and began to shudder . I was in the middle lane of three westbound marked lanes and was almost hit by a driver behind me which had been following too closely. The check engine and traction control light came on and my oil gauge went to the high side. I exited onto [xxx] and at 40 MPH the truck would shake and shudder until I drove the 6 miles to my residence. On [xxx], I had the vehicle towed to lash GMC dealership in johnstown ohio. Once there the vehicle was diagnosed with a failed lifter that broke into pieces resulting in a bent rod and damaged cam shaft. The dealer recommended full engine replacement due the severity of the failure. The truck is a 2018 GMC sierra denali with only 65,449 miles on it. It cost almost $70,000.00 new and the replacement engine cost me $14,221.96. I feel my personal safety was jeopardized in this incident. Since that time I have researched the 6.2 GMC engine online and have found reports of numerous similiar failures and incidents involving the engine in question. I truly feel NHTSA should take a strong look at the engine failures involving this engine and force GMC to repair or replace the engines in question due to the safety issues involving the engines failures in traffic and the risk associated with an occurence. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
NHTSA complaint #11645115
Feb 6, 2025engine
I have a 2018 GMC Sierra 1500 with a 6.2 motor. Back in december of 2024, I had to replace a tie rod, cam shaft, and the lifters. $8400 to get everything replaced. Since my warranty had expired, I had to pay all of this out of pocket. I know there is currently an investigation going on in GMC's 6.2 motors. Almost 900,000 engine failures. This is unacceptable. GMC just needs to… Read more
I have a 2018 GMC Sierra 1500 with a 6.2 motor. Back in december of 2024, I had to replace a tie rod, cam shaft, and the lifters. $8400 to get everything replaced. Since my warranty had expired, I had to pay all of this out of pocket. I know there is currently an investigation going on in GMC's 6.2 motors. Almost 900,000 engine failures. This is unacceptable. GMC just needs to man up and send out the recall notice. Since I have already had to pay for my replacements, GMC should do the right thing and and cut me a check.
NHTSA complaint #11641037
Feb 4, 2025engine
Lifters and cams fatal failure, requiring extremely pricy replacement of the parts affected or replacement of the entire engine!
NHTSA complaint #11640668