Mar 28, 2025service brakes, hydraulic
The contact owns a 2006 Ford F-150. The contact stated that while coming to a stop, the brake pedal was depressed but failed to function as intended. The contact stated that the vehicle failed to stop and continued rolling forward. The contact stated that the vehicle came to a stop once the brake pedal was depressed to the floorboard. No warning lights were illuminated. The… Read more
The contact owns a 2006 Ford F-150. The contact stated that while coming to a stop, the brake pedal was depressed but failed to function as intended. The contact stated that the vehicle failed to stop and continued rolling forward. The contact stated that the vehicle came to a stop once the brake pedal was depressed to the floorboard. No warning lights were illuminated. The contact stated that the vehicle returned to normal function afterwards. The local dealer was contacted; however, the dealer refused to diagnose the vehicle because of its age of the vehicle. The vehicle was not repaired. The contact stated that on a separate occasion, while the contact's husband was driving at a slow speed, the brake pedal was depressed but failed to function as intended. The contact stated that the vehicle failed to stop and continued rolling forward. The contact's husband stated that the vehicle came to a stop once the brake pedal was depressed to the floorboard. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA hotline. The failure mileage was approximately 145,000.
NHTSA complaint #11651318
Jun 15, 2022service brakes, hydraulic
The contact owns a 2006 Ford F-150. The contact stated while driving 30 MPH, he had to forcefully depress the brake pedal to stop the vehicle. The contact stated that the check engine warning light was illuminated. The contact was able to continue driving to his residence. The vehicle was not diagnosed or repaired. A dealer was not contacted. Upon investigation, the contact… Read more
The contact owns a 2006 Ford F-150. The contact stated while driving 30 MPH, he had to forcefully depress the brake pedal to stop the vehicle. The contact stated that the check engine warning light was illuminated. The contact was able to continue driving to his residence. The vehicle was not diagnosed or repaired. A dealer was not contacted. Upon investigation, the contact associated the failure with NHTSA campaign number: 08v208000 (service brakes, hydraulic) however, the VIN was not included. The manufacturer had not been informed of the failure. The failure mileage was approximately 165,000.
NHTSA complaint #11469292
Aug 9, 2021service brakes, hydraulic
Random brake loss due to hydraulic control unit for ABS. The loss of brakes on more than 5 occasions has nearly caused several accidents as brakes fail to engage in traffic situations. The problem cannot be reproduced by automotive repair shops due to the random nature of the events. Inspection of the component does not reveal any problem. The component functions properly… Read more
Random brake loss due to hydraulic control unit for ABS. The loss of brakes on more than 5 occasions has nearly caused several accidents as brakes fail to engage in traffic situations. The problem cannot be reproduced by automotive repair shops due to the random nature of the events. Inspection of the component does not reveal any problem. The component functions properly 80% of the time. There has never been any warning of any sort prior to the event happening which is why the severity of the incidents are not only surprising but have put me and other drivers at risk. These hcu components have had similar failures in other Ford vehicles. Recalls are listed for those vehicles such as the mzk, fusion, millan.
NHTSA complaint #11428281
Jun 2, 2021electrical system, service brakes
There is a very common problem with the brake light always being on due to a short circuit in the cluster, many owners have reported this problem for several manufacturing years, the brake light is always on even though there is no problem with the brakes. This creates a great hazard because if you do have a brake problem since the light is always on you will never know, and… Read more
There is a very common problem with the brake light always being on due to a short circuit in the cluster, many owners have reported this problem for several manufacturing years, the brake light is always on even though there is no problem with the brakes. This creates a great hazard because if you do have a brake problem since the light is always on you will never know, and you may be in a fatal vehicle accident. Ford motor company should replace or repair all clusters that have this problem.I just purchased this vehicle with this very common problem. Your inspector can google it and will find this is indeed a very common problem.
NHTSA complaint #11419376
Jan 9, 2021suspension, service brakes, forward collision avoidanceCrash
It was hard to stop
NHTSA complaint #11387300
Feb 4, 2020service brakesCrash
ABS brake system not working properly pedal goes to floor
NHTSA complaint #11306998
Sep 12, 2019electrical system, service brakes
Brake light continuously on due to fault in cluster panel. Safety issue in not knowing when there are braking problems.
NHTSA complaint #11254970
Jun 4, 2019electrical system, exterior lighting, service brakes
Ford F-150 fx4 140,000.0 miles. Brake light has been on for several years starting around 2010 with 76,000.0 miles. The brakes were replaced and flushed multiple times since the problem started. Replaced brake cable e-brake switch etc... Everything points to the cluster and there are multiple websites the verify the same exact problem with the brake light beginning from… Read more
Ford F-150 fx4 140,000.0 miles. Brake light has been on for several years starting around 2010 with 76,000.0 miles. The brakes were replaced and flushed multiple times since the problem started. Replaced brake cable e-brake switch etc... Everything points to the cluster and there are multiple websites the verify the same exact problem with the brake light beginning from 2004-2010. In some states this is an indpectable item adding additional and mandatory repairs to be made. The cluster repair part cost anywhere from $400.00-$600.00 and with labor could run well over $1000.00 pending on the model of the F-150. My bottom line is that this issue has gone without a recall from Ford or the NHTSA.
NHTSA complaint #11217744
Aug 1, 2017service brakes
Tl* the contact owns a 2006 Ford F-150. The contact received notification of NHTSA campaign number: 08v208000 (service brakes, hydraulic); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The auto nation Ford dealer was contacted and confirmed that the parts were not… Read more
Tl* the contact owns a 2006 Ford F-150. The contact received notification of NHTSA campaign number: 08v208000 (service brakes, hydraulic); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The auto nation Ford dealer was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue. The failure mileage was 144,000. Parts distribution disconnect.
NHTSA complaint #11011927
Jun 8, 2017service brakes, engine, fuel/propulsion system
Ford f150 xlt 2006 should have a mandatory safety recall for the fuel control module. This is clearly a design defect and a major safety concern. I was driving down vt116 (a hilly, winding 2 lane country highway with no shoulder) in the rain at about 40mph when my truck started to buck and lose power. There was no place to pull over, so I put my hazards on and tried to… Read more
Ford f150 xlt 2006 should have a mandatory safety recall for the fuel control module. This is clearly a design defect and a major safety concern. I was driving down vt116 (a hilly, winding 2 lane country highway with no shoulder) in the rain at about 40mph when my truck started to buck and lose power. There was no place to pull over, so I put my hazards on and tried to limp it to a safe place to pull over. The engine stalled and I lost steering and braking power on a curve. I applied the brakes manually and wrestled the steering wheel (which no longer had any power assist). With major difficulty, I was able to bring the truck to a controlled stop. I was then able to restart the engine, limped along at 15mph, bucking and stalling 3 more times before getting to a safe place to pull over. This is the second time I have had my fcm replaced (prior was 1/5/2013) and the second time I almost crashed my truck because of this defect. The previous time was january 2013 on a mountain road in winter on snow. If I was towing my boat on the interstate and lost all power, I would probably have been killed along with anyone around me. Why is it a design defect? Because this electronic component is installed in a weather-exposed area above the spare tire and is not corrosion-proof. In any rust belt state (or a place exposed to salt), the case will corrode, exposing the circuit board to water, causing the unit to fail. Why is it a safety concern? Because when the fcm fails, the
NHTSA complaint #10993883
Apr 25, 2017service brakes
My ABS brake system failed. The light for ABS came on and the brakes failed to ingage on a dry road. I had to vear off the road to avoid another truck making a turn. This happened again with a car infront of me, before I got home and parked the truck. The brakes shutter on pressing them and then fail to ingauge. I had the problem fixed in goodyear az at the fird dealer for… Read more
My ABS brake system failed. The light for ABS came on and the brakes failed to ingage on a dry road. I had to vear off the road to avoid another truck making a turn. This happened again with a car infront of me, before I got home and parked the truck. The brakes shutter on pressing them and then fail to ingauge. I had the problem fixed in goodyear az at the fird dealer for over 800 dollars and now the problem began again. I live in lakeside arizona and cant drive the truck back to that dealer without fear of dying on the side of a cliff ir in a bad accident because my brakes fail to stop the vehicle and brakes are needed to go through the mountsins to get to that dealer. Very upset that I bought this truck from cactus jacks in phoenix az. 560 dollars a month for a truck I cant drive for my small farm. I would like to trade in tbis truck for one I can trust that wont be the death of me or my family.
NHTSA complaint #10980370
Apr 20, 2017service brakes, engine
Tl* the contact owns a 2006 Ford F-150. While driving 45 MPH, the front of the vehicle shook violently, the engine nearly stalled and lost power repeatedly, and the check engine indicator illuminated intermittently. The vehicle also braked independently. The vehicle was taken to an uncertified mechanic who diagnosed that the engine was having multiple misfires, and did not… Read more
Tl* the contact owns a 2006 Ford F-150. While driving 45 MPH, the front of the vehicle shook violently, the engine nearly stalled and lost power repeatedly, and the check engine indicator illuminated intermittently. The vehicle also braked independently. The vehicle was taken to an uncertified mechanic who diagnosed that the engine was having multiple misfires, and did not know how to repair the vehicle. The contact also called a dealer who was extremely rude and did not assist. The vehicle was not repaired. The manufacturer was made aware of the failure. The contact was informed that they would not assist because the claims deadline had been missed. The approximate failure mileage was 128,000.
NHTSA complaint #10979677
Dec 25, 2016steering, service brakes, engine
Was driving my 2006 F-150 over a mountain pass in canada. There was compact snow and ice on the roadway and I was traveling with other vehicles around me at approximately 40 MPH. The vehicles ahead of me began to brake, I as well tried to brake only to find my truck had lost power and was no longer running. I had lost power to my brakes and steering. This caused my truck to… Read more
Was driving my 2006 F-150 over a mountain pass in canada. There was compact snow and ice on the roadway and I was traveling with other vehicles around me at approximately 40 MPH. The vehicles ahead of me began to brake, I as well tried to brake only to find my truck had lost power and was no longer running. I had lost power to my brakes and steering. This caused my truck to begin sliding on the snow and ice and I was unable to control my vehicle. The cars around me were slowing and stopping and I could not. I began to fish tail in both directions while trying desperately to control my truck with no brakes or power steering, I eventually did a complete 360 degree spin and somehow managed to get the truck under control with out rolling over and into the ditch or smashing into the other vehicles around me. When I came to a stop my truck was not running and the dash lights were on. I placed the transmission into drive and restarted the truck without issue and continued on without issue. This is the second time this has happened with this truck, the first time I was on a residential street and I was able to just coast to a stop and restarted the truck. This last incident on the mountain pass has confirmed to me that I will not own another Ford as I have researched this problem to find that this is a common issue with Ford trucks. I am certain this has caused major accidents if not deaths and the fact there are no error codes left behind from the events to verify this has hap
NHTSA complaint #10937392
Sep 20, 2016service brakes
Was sitting at a restaurant drive thru with foot on the brake when the brake pedal suddenly went to the floor and the truck started moving. I was able to get the vehicle home and back to the Ford dealership the next morning very carefully and by pumping the brakes to get the vehicle to stop. Was told that the brake line had ruptured. Luckily, I was not towing my 6000 pound… Read more
Was sitting at a restaurant drive thru with foot on the brake when the brake pedal suddenly went to the floor and the truck started moving. I was able to get the vehicle home and back to the Ford dealership the next morning very carefully and by pumping the brakes to get the vehicle to stop. Was told that the brake line had ruptured. Luckily, I was not towing my 6000 pound boat or going downhill at the time of the failure. I asked if this was common since brake lines are not an item that are routinely inspected or replaced on a normal 17 point inspection. I was told that it was uncommon. I googled the problem and discovered that several other Ford f150 owners of various model years had experienced the same issue. Luckily, there have been no reports of deaths or severe injury, but I am reporting this to hopefully prevent a death from occurring.
NHTSA complaint #10908094
Jun 3, 2016electrical system, service brakes
After countless hours spent diagnosing a dash brake lite warning. These vehicles factory defect is the electronics board or speedometer cluster. Countless people are driving with a brake light on with nothing possibly wrong.when something does go wrong they may not have a clue until the vehicle has no brakes.
NHTSA complaint #10872470
Oct 7, 2015service brakes, hydraulic
Tl* the contact owns a 2006 Ford F-150. The contact stated that the brake pedal excessively abnormally traveled to the floorboard. The vehicle was taken to the dealer where it was informed that the vehicle was functioning as designed. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 200. Updated 1/12/2016 *cn the… Read more
Tl* the contact owns a 2006 Ford F-150. The contact stated that the brake pedal excessively abnormally traveled to the floorboard. The vehicle was taken to the dealer where it was informed that the vehicle was functioning as designed. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 200. Updated 1/12/2016 *cn the consumer stated when he attempted to brake, his foot also hit the accelerator pedal. The consumer stated the brake and accelerator were too close together. Updated 05/04/16
NHTSA complaint #10780635
Jun 22, 2015service brakes
Tl* the contact owns a 2006 Ford F-150. While driving at 20 MPH, the brakes auto engaged without warning. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The VIN was not available. The approximate failure mileage was 80,000. Updated 09/03/15*lj updated 10/26/2017*cn
NHTSA complaint #10726596
Mar 11, 2015service brakes, engine, fuel/propulsion system
2006 F-150 lost all power function while traveling down the interstate. I lost power steering and brakes. The cause is a corrosive fuel pump control module. After taking with my local Ford dealer I was made aware that this is major safety issue and one that fmc refuses to recognize. This incident could have resulted in a major accident. I was lucky enough to be able to signal… Read more
2006 F-150 lost all power function while traveling down the interstate. I lost power steering and brakes. The cause is a corrosive fuel pump control module. After taking with my local Ford dealer I was made aware that this is major safety issue and one that fmc refuses to recognize. This incident could have resulted in a major accident. I was lucky enough to be able to signal to the cars around me that I was having trouble - however I was still almost rear ended twice before being able to pull off to the side of the road. *tr
NHTSA complaint #10693652
Aug 15, 2014structure, vehicle speed control, service brakesCrash
Gas and brake pedal are too close together. You could still be giving it gas while you are pushing on the brakes. I see hundreds of complaints about this online.I was pulling into a parking spot when I thought I was applying the brakes the other half of my foot was on the gas causing me to jump the curb and crash into a wall. *tr
NHTSA complaint #10622576
Jul 23, 2014service brakes
As a part of regular maintenance I always have well in advance performed scheduled maintenance on my 06 F-150.on aug 23 2013 I had my rotors and brake pads all replaced as well as having a hi pressure brake fluid change performed as part of this as suggested by the bill currie Ford dealership in tampa. The truck had 83,996 miles on it at this time of service. The truck was… Read more
As a part of regular maintenance I always have well in advance performed scheduled maintenance on my 06 F-150.on aug 23 2013 I had my rotors and brake pads all replaced as well as having a hi pressure brake fluid change performed as part of this as suggested by the bill currie Ford dealership in tampa. The truck had 83,996 miles on it at this time of service. The truck was rarely driven after that and used only on short trips.of 10-20 miles or less after having the brakes serviced. Friday july 18th 2014..the tuck had only approx. 2000 additional miles on it after the brakes were serviced at bill currie Ford.I and a friend were driving to pickup a washing machine about 30 miles away. Without warning. Upon returning the right wheel began pulling to the right and smoke and a rubber and plastic smell accompanied by smoke starting rising from the right wheel well which was scotching hot. The heat was so intense that when we stopped the plastic wheel cover fell off because its was melted.it was taken to the dealership were the original work was performed. I was informed it was the caliper,that it had seized and that after already having replaced the front rotor several thousand miles before//the right rotor and caliper and brake line would now have to be replaced again..because they said.."we can't tell when a caliper will fail". Now it has cost me $2,300,00 to get my brakes done..when initially they were still in safe limits.we were lucky this didn't cause a fire or cause th
NHTSA complaint #10615804
Jun 2, 2014service brakes
Tl-the contact owns a 2006 Ford F-150. The contact stated while driving 5 MPH the brake would not engage, it was very hard to apply. The contact had to apply the manual brake to stop. The vehicle was taken to an independent mechanic who noticed the brake booster vacuum hose had collapsed. The contact was made aware of a recall notification under NHTSA campaign id number… Read more
Tl-the contact owns a 2006 Ford F-150. The contact stated while driving 5 MPH the brake would not engage, it was very hard to apply. The contact had to apply the manual brake to stop. The vehicle was taken to an independent mechanic who noticed the brake booster vacuum hose had collapsed. The contact was made aware of a recall notification under NHTSA campaign id number 08v208000 (service brakes, hydraulic),however, his VIN was not included. The vehicle had not been repaired. The manufacturer was informed of the problem. The approximate failure mileage was 180,000.
NHTSA complaint #10595483
Mar 18, 2014service brakes
Tl* the contact owns a 2006 Ford f150. The contact stated that while driving approximately 5 MPH, the brake pedal was depressed and there was a delayed response. The vehicle had been previously repaired under NHTSA campaign id number 08v208000 (service brakes, hydraulic). The failure recurred because the recall remedy failed to correct the problem. The contact diagnosed the… Read more
Tl* the contact owns a 2006 Ford f150. The contact stated that while driving approximately 5 MPH, the brake pedal was depressed and there was a delayed response. The vehicle had been previously repaired under NHTSA campaign id number 08v208000 (service brakes, hydraulic). The failure recurred because the recall remedy failed to correct the problem. The contact diagnosed the vehicle and replaced the manifold hose himself. The manufacturer was notified of the problem. The approximate failure mileage was 92,000.
NHTSA complaint #10573222
Dec 27, 2012service brakesCrash1 injured
Tl* the contact owns a 2006 Ford f150. The contact stated that while driving 30 MPH during a rain storm and depressing the brakes, the vehicle exhibited and unusually lound double clunking noise as the vehicle skidded and flipped over. The vehicle did not crash into any other object. The police were notified however, a report was not filed. The contact sustained an amputated… Read more
Tl* the contact owns a 2006 Ford f150. The contact stated that while driving 30 MPH during a rain storm and depressing the brakes, the vehicle exhibited and unusually lound double clunking noise as the vehicle skidded and flipped over. The vehicle did not crash into any other object. The police were notified however, a report was not filed. The contact sustained an amputated arm during the crash. The vehicle was towed by the police and was deemed as destroyed. The contact mentioned that just prior to the crash, the vehicle was taken to firestone for maintenance and the replacement of the rotor and front brake pad. The manufacturer was not notified of the incident. The failure mileage was 78,912. Updated 2/4/13 *cn updated 2/20/2013 *js
NHTSA complaint #10490218
Nov 30, 2012structure, vehicle speed control, service brakesCrash1 injured
I am 6'5" and wear size 16 shoes. With my size and the distance to the pedal my legs go a little to the side and my shoe is at an angle to the petals lets say 30 degrees. I wearing typical work boot (like in Ford commercials) which the laces have pegs the shoe laces go around. These pegs are the same as all work boots (red wings - $300 boot). What happened is because the… Read more
I am 6'5" and wear size 16 shoes. With my size and the distance to the pedal my legs go a little to the side and my shoe is at an angle to the petals lets say 30 degrees. I wearing typical work boot (like in Ford commercials) which the laces have pegs the shoe laces go around. These pegs are the same as all work boots (red wings - $300 boot). What happened is because the brake pedal has a thick rubber pad that stretches around the metal brake pedal and leaves a ridge in the back of the pedal all the way around (so the rubber fitting goes over it like a shower cap). Also the truck is an automatic and the break pedal is very large. While backing up giving just a little gas my boot shoe lace peg got trapped behind the brake pedal and was holding my foot on the gas pedal depressing it down. Because the rubber ridge runs all the way around my pedal (as designed) I could not move my foot to the side of the brake pedal to release the gas. Because of the thickness of my foot when I pressed the break with my other foot, it moves the gas pedal down at the same rate as my foot is trapped, so the more you press the brake the more you give gas at a ratio that does not let me stop the vehicle. (note I use only one foot for the gas and brake normally but with my right foot trapped I had no other choice but to use my left foot to brake and try to get it the truck out of gear . I could not do anything in time and hit a stationary building. If someone was behind me, they would
NHTSA complaint #10486507
Mar 18, 2010service brakes, hydraulic, air bags, equipmentCrash
My son was killed in his 2006 Ford 150 pickup truck driving 45 miles an hour. His truck apparently left the road with no signs of brakes being applied, flipped several times. The airbags never deployed. His insurance company was threatening me to release the truck from storage which I did. I have since regained my senses enough to search the web and see that there were many… Read more
My son was killed in his 2006 Ford 150 pickup truck driving 45 miles an hour. His truck apparently left the road with no signs of brakes being applied, flipped several times. The airbags never deployed. His insurance company was threatening me to release the truck from storage which I did. I have since regained my senses enough to search the web and see that there were many recalls on the brake lines of this make truck. *tr
NHTSA complaint #10320731
Dec 29, 2009service brakes, hydraulicCrash
Tl* the contact owns a 2006 Ford F-150. While attempting to park in the driveway he applied the brakes, but the vehicle would not stop. Consequently the vehicle crashed into his home. The vehicle was taken to the dealership, but the technician could not determine the cause of the failure. The current and failure mileages were 44000.
NHTSA complaint #10297378
Dec 10, 2008service brakes, hydraulic, air bagsCrash2 injured
Tl*the contact owns a 2006 Ford f150. On november 19, 2008, the vehicle was repaired according to Ford recall number 08s05b (brake booster vacuum hose replacement). While driving 35 MPH, the vehicle failed to stop when the brake pedal was depressed. The contact struck the side of another vehicle and the air bags failed to deploy. The road pavement was dry. The contact and… Read more
Tl*the contact owns a 2006 Ford f150. On november 19, 2008, the vehicle was repaired according to Ford recall number 08s05b (brake booster vacuum hose replacement). While driving 35 MPH, the vehicle failed to stop when the brake pedal was depressed. The contact struck the side of another vehicle and the air bags failed to deploy. The road pavement was dry. The contact and the other passenger in his vehicle were transported to the emergency room for back injuries and bruises. Both occupants were wearing their seat belts at the time of the crash. The front end of the vehicle was damaged; however, both vehicles were able to be driven from the scene. A police report was filed. The failure mileage was 39,537.
NHTSA complaint #10251272
Dec 1, 2008electrical system, service brakes, electricFire
Ford F-150 would not shut off, removed fuse to fuel pump. Found energy to other components not on. Removed negative battery terminal. Had vehicle towed to dealer. Report from dealer wire harness from ABS system burnt sending energy throughout truck. Dealer said truck should have burned up. Dealer could not confirm if problem was with ABS or harness. *tr
NHTSA complaint #10250399
Oct 21, 2008service brakes, hydraulicCrash
Brake booster recall notice on 2006 f150 harley. On september 13, 2008 I left my vehicle in paramus Ford n.j. For recall repair and other issues. When I returned the manager didn't have time for recall. On september 26, 08 I hit another car because brakes didn't stop. I hope that someone looks into these braking system because this was a scary accident with out being prepared. *tr
NHTSA complaint #10246264
Jun 13, 2008service brakes, hydraulicCrash
Tl*the contact owns a 2006 Ford F-150. When the contact attempted to start the vehicle, the engine backfired. The vehicle finally started, and when the contact attempted to back up the vehicle, he realized that the power brakes failed. He struck a vehicle parked behind him. The brakes were extremely heavy and there was no power assist. Four days later, he took the vehicle… Read more
Tl*the contact owns a 2006 Ford F-150. When the contact attempted to start the vehicle, the engine backfired. The vehicle finally started, and when the contact attempted to back up the vehicle, he realized that the power brakes failed. He struck a vehicle parked behind him. The brakes were extremely heavy and there was no power assist. Four days later, he took the vehicle to the dealer and the technician informed him that the vacuum hose was loose, which caused the power assist failure. The vehicle was repaired at the owner's expense. The contact filed a consumer review request with the dealer to apply for an extended warranty, but his request was denied. After further research, the contact realized that his failures were identical to NHTSA campaign id number 08v208000 (service brakes, hydraulic:power assist:vacuum:hoses, lines/piping, and fittings); however, the manufacturer stated that the VIN was not included in the recall. The failure mileage was 70,000 and current mileage was 90,000.
NHTSA complaint #10230913
Jun 11, 2008service brakes, hydraulicCrash
Tl*the contact owns a 2006 Ford F-150. While depressing the brake pedal, the contact's foot simultaneously depressed the accelerator pedal. As a result, the vehicle struck the front end of another vehicle. There were no injuries. The contact did not notice any differences in the vehicle prior to the failure. The speed was unknown. The current mileage was 35,345 and… Read more
Tl*the contact owns a 2006 Ford F-150. While depressing the brake pedal, the contact's foot simultaneously depressed the accelerator pedal. As a result, the vehicle struck the front end of another vehicle. There were no injuries. The contact did not notice any differences in the vehicle prior to the failure. The speed was unknown. The current mileage was 35,345 and failure mileage was 32,000. Updated 07/10/08. *lj updated 07/08/08
NHTSA complaint #10230755
Jun 2, 2008service brakes, hydraulicCrash1 injured
Tl*the contact owns a 2006 Ford f150. The brakes failed when the pedal was depressed and the contact struck a tree. She was transported to the hospital by an ambulance and sustained rib fractures and contusions. The vehicle was destroyed. NHTSA campaign id number 08v2078000 (service brakes, hydraulic:power assist:vacuum:hoses, lines/piping, and fittings) was referenced. A… Read more
Tl*the contact owns a 2006 Ford f150. The brakes failed when the pedal was depressed and the contact struck a tree. She was transported to the hospital by an ambulance and sustained rib fractures and contusions. The vehicle was destroyed. NHTSA campaign id number 08v2078000 (service brakes, hydraulic:power assist:vacuum:hoses, lines/piping, and fittings) was referenced. A police report was filed. The speed was unknown. The current and failure mileages were 16,000.
NHTSA complaint #10229481
Oct 30, 2007service brakes, hydraulicFire
Tl*the contact owns a 2006 Ford F-150. The contact heard a popping sound and noticed smoke under the hood and dashboard when the vehicle was started. The noise sounded as if the vehicle backfired. While driving 55 MPH, the power brakes failed without warning. The contact applied the emergency brake to stop the vehicle and pulled off the road. He noticed that the vacuum… Read more
Tl*the contact owns a 2006 Ford F-150. The contact heard a popping sound and noticed smoke under the hood and dashboard when the vehicle was started. The noise sounded as if the vehicle backfired. While driving 55 MPH, the power brakes failed without warning. The contact applied the emergency brake to stop the vehicle and pulled off the road. He noticed that the vacuum hose was detached from the manifold, which supplies vacuum power to the brake booster. The vehicle was towed to a Ford dealer. The dealer placed the vacuum hose back on the engine and informed the contact that it should be replaced. The weather was not a factor. The current mileage was 23,000 and failure mileage was 22,000. Updated 11/15/07 *tr
NHTSA complaint #10207421
Feb 11, 2007service brakes, hydraulicCrash
While pulling into a parking spot at a local gas station(5 - 8 MPH), I applied the brake to stop and it went all the way to the floor. The truck jumped the sidewalk and crashed into the building. After picking the truck up the next day, the brakes worked fine and everybody thinks I'm nuts! Currently having truck accessed by different sources. *jb
NHTSA complaint #10182248
Dec 19, 2006service brakes, hydraulicCrash
Tl* - the contact was driving at 8 - 10 miles per hour, and applied the brakes. The car accelerated and crashed into a wall and was badly dmaged on the passenger side. The contact states that this has happened before. We will be contacting the caller for more information.
NHTSA complaint #10176615
Nov 7, 2006service brakes, hydraulic, vehicle speed controlCrash3 injured
I was involved in an accident which was caused by hitting the brake pedal and the accelerator at the same time. I thought I was hitting the brake when and hit the gas at the same time causing my vehicle to rear end collide with the vehicle in front of me. Since I have been driving the vehicle this has happened several times, the gas pedal is too close in height to the brake pedal. *nm
NHTSA complaint #10172822
Oct 26, 2006service brakes, hydraulicCrash
Dt*: the contact stated while applying brake pressure at 5 MPH in a parking lot, the brake pedal extended all the way to the floor board, and there was an increased stopping distance which resulted in a rear end collision. No injuries were sustained; the contact was wearing a seat belt. The vehicle sustained minor damage. The police were not alerted. The vehicle was towed… Read more
Dt*: the contact stated while applying brake pressure at 5 MPH in a parking lot, the brake pedal extended all the way to the floor board, and there was an increased stopping distance which resulted in a rear end collision. No injuries were sustained; the contact was wearing a seat belt. The vehicle sustained minor damage. The police were not alerted. The vehicle was towed to the dealer who was unable to duplicate the problem.
NHTSA complaint #10171875
Aug 28, 2006service brakes, hydraulicCrash
Dt*: the contact stated while traveling 25 MPH, the brake pedal was depressed and went to the floor. The vehicle did not stop, and collided into the rear of another vehicle. There were no injuries, but both vehicles sustained minor damage. The dealership determined this was how the vehicle was manufactured.
NHTSA complaint #10166766
Jun 22, 2006service brakes, hydraulicCrash
On 15 june 2006, my wife was involved in a accident while operating a 2006 Ford f150. A vehicle stopped in front of her she pressed the brakes and the vehicle did not responded to her braking action. When I arrived at the scene of the accident, I pressed the brakes and they went to the floor of the vehicle. The vehicle was taken to woody andersen Ford in huntsville, alabama… Read more
On 15 june 2006, my wife was involved in a accident while operating a 2006 Ford f150. A vehicle stopped in front of her she pressed the brakes and the vehicle did not responded to her braking action. When I arrived at the scene of the accident, I pressed the brakes and they went to the floor of the vehicle. The vehicle was taken to woody andersen Ford in huntsville, alabama and the service manager verified that the brakes indeed went to the floor. We waited a week for a Ford engineer to verify the problems and he stated that when he drove the vehicle it was okay at that time. These brakes failed my wife at 5 miles an hour and caused her to have an accident. No action has been taken to resolve this issue. *nm
NHTSA complaint #10160551
Mar 17, 2006service brakes, hydraulicCrash
Dt*: the contact stated while driving 10 MPH attempting to apply brake pressure around a curve the vehicle accelerated without warning. This occurred on a normal road during normal braking. The driver was wearing a seat belt and a police report was filed at the scene. The vehicle went into a three foot ditch and had to be pulled out. It sustained frontal damage and the… Read more
Dt*: the contact stated while driving 10 MPH attempting to apply brake pressure around a curve the vehicle accelerated without warning. This occurred on a normal road during normal braking. The driver was wearing a seat belt and a police report was filed at the scene. The vehicle went into a three foot ditch and had to be pulled out. It sustained frontal damage and the tow bar was bent. The vehicle was taken to the dealership for inspection. They replaced the tow hook, front license plate bracket and balanced the front end of the vehicle. However, after the accident, the contact received recall #06c11, concerning the hydraulic and electrical brake system. The manufacturer was alerted.
NHTSA complaint #10153063