The contact owns a 2005 Ford F-150. The contact stated while driving at an undisclosed speed and approaching a stop sign, he had to pump the brake pedal to fully stop the vehicle. The contact stated no warning light was illuminated. The vehicle was not diagnosed or repaired. A dealer was not contacted. The manufacturer had been informed of the failure. The failure mileage was unknown.
2005 Ford F-150 brakes problems
122 owners reported brakes problems — 11% of all 1,112 complaints about the 2005 Ford F-150.
Brakes complaints by Ford F-150 year
What owners report
My brake booster or vacuum line has went out during driving and I almost lost control with my family. I see theres recalls on my make model and year. So I wanted to check and see because it was scary I had to leave my truck and get it towed some how back still also.
The contact owns a 2005 Ford F-150. The contact stated while driving approximately 30 MPH and depressing the brake pedal, the brake pedal traveled to the floor. The driver immediately turned the steering to avoid hitting several kids that were crossing the street. During the failure, the brake warning light illuminated. The cause of the failure was not yet determined. The… Read more
The contact owns a 2005 Ford F-150. The contact stated while driving approximately 30 MPH and depressing the brake pedal, the brake pedal traveled to the floor. The driver immediately turned the steering to avoid hitting several kids that were crossing the street. During the failure, the brake warning light illuminated. The cause of the failure was not yet determined. The local dealer was notified of the failure. The contact was informed that the part to replace the ABS module was no longer produced by the manufacturer and was therefore unavailable for a repair. The manufacturer was not notified of the failure. The failure mileage was 174,000.
Me enter hoy que mi truck tena varios recall y no he recibido aviso, gracias por su atencion.
The brake warning lite remains on. I'm told by my mechanic that it is due to a broken connection in the dash board circuit board and he said it is a relatively common fault. Repair requires removing the entire dash board and replacement of the circuit board.
1. Brake dot 3 is running out after several months. When I apply the brakes, the vehicle keeps going. In order to keep the vehicle running, I must push down the brake very hard to stop the vehicle. I have to constantly refill the oil tank. 2. When driving on the highway and the speed reaches at around 45-65 MPH, the vehicle automatically loses power and hit at 3-5 MPH before… Read more
1. Brake dot 3 is running out after several months. When I apply the brakes, the vehicle keeps going. In order to keep the vehicle running, I must push down the brake very hard to stop the vehicle. I have to constantly refill the oil tank. 2. When driving on the highway and the speed reaches at around 45-65 MPH, the vehicle automatically loses power and hit at 3-5 MPH before stopping. After I completely turn off and reset the battery, the vehicle starts normal again. The vehicle happened from 2009 to current time, but the odb scan does not detect any code or errors.
While driving, my f150 without warning, died 3 times in 1/2 mile. Leaving me with no power steering, power brakes. Very dangerous. Nearly had a accident. Had 1/2 tank of gas. New battery. It did not give a code. I did get it started each time and was able to drive it home. Now I am afraid to drive it.
My 2005 Ford f150 truck has had so many problems & some replace twice & im over it im about to have a heart attack now it sounds like my aculator again with the sound of metal scraping on the ground and when I switch it to 44 the sounds stops .but if its not in 44 the sound stays and it is loud ! I have spent so much get my truck fixed and what upsets me is I take care of my… Read more
My 2005 Ford f150 truck has had so many problems & some replace twice & im over it im about to have a heart attack now it sounds like my aculator again with the sound of metal scraping on the ground and when I switch it to 44 the sounds stops .but if its not in 44 the sound stays and it is loud ! I have spent so much get my truck fixed and what upsets me is I take care of my truck change oil spark plugs everything since purchased in 2005 brand new and im over it something needs to done with all these parts defected and it will continue until something is done.
Tl* the contact owns a 2005 Ford F-150. While driving 40 MPH, the two front wheels on the vehicle seized without warning. The contact stated that the failure occurred on at least eight occasions. The dealer was not contacted. The manufacturer was made aware of the issue and provided case number: cas12702472. In addition, the contact cited NHTSA campaign number: 08v208000… Read more
Tl* the contact owns a 2005 Ford F-150. While driving 40 MPH, the two front wheels on the vehicle seized without warning. The contact stated that the failure occurred on at least eight occasions. The dealer was not contacted. The manufacturer was made aware of the issue and provided case number: cas12702472. In addition, the contact cited NHTSA campaign number: 08v208000 (service brakes, hydraulic) as a possible cause of the failure. The failure mileage was 230,000.
Had new brakes installed several years because it was shaking and almost impossible to stop at highway speed. Well it is happening again if you are traveling highway speed. Brakes are very bad again. This vehicle has about 55,000 miles on it and should not have worn out brakes for the second time. Something is terribly wrong with the braking system. I am to the point of… Read more
Had new brakes installed several years because it was shaking and almost impossible to stop at highway speed. Well it is happening again if you are traveling highway speed. Brakes are very bad again. This vehicle has about 55,000 miles on it and should not have worn out brakes for the second time. Something is terribly wrong with the braking system. I am to the point of being afraid to drive it on the highway because you have to mash hard on the brake and feel the front shaking before it will finally stop!
Brake booster vacuum supply metal stand pipe ruptured. This was while driving. Loss of vacuum and loss of engine performance and brakes were sluggish. Have to push all way to floor.
The brakes faded during a emergancy stop on the hiway. I was able to get stopped but the break peddel went clear to the floor.I could not pump up the peddel to make the breake work any better.
Fuse 14 controlling ABS module, dtr sensor, reverse lights, pcv heater, air conditioner compressor, cruise control deactivator switch and daytime headlights was repeatedly blowing. Truck was serviced by dealer on 3-23-16, replacing the A/C compressor. Replacing the A/C compressor did not resolve any issues. The truck was returned to the dealer on 4-6-16 for the same issue with… Read more
Fuse 14 controlling ABS module, dtr sensor, reverse lights, pcv heater, air conditioner compressor, cruise control deactivator switch and daytime headlights was repeatedly blowing. Truck was serviced by dealer on 3-23-16, replacing the A/C compressor. Replacing the A/C compressor did not resolve any issues. The truck was returned to the dealer on 4-6-16 for the same issue with the same fuse. The dealership replaced the fuse and performed diagnostic tests on the truck, then informing me that they could not diagnose or locate the short. The dealership informed me that I would have to drive the truck until the fuse started blowing more frequently. The first time the truck was driven after work was performed the cruise control was not functioning properly. The truck engine would surge as the truck went down the road with the cruise control on. The issue with the cruise control happened on 4-9-16. On the morning of 4-10-16 the truck was driven approximately 4 miles and parked in the drive of my home. After entering the house the alarm was heard sounding on the vehicle, at which time I stepped outside to find the truck on fire. The fire seemed to have started on the inside of the truck.
I purchased my 2005 f150 with a 5.4l trinitron engine used in 2010. I completed all regular scheduled maintenance using the recommended products, most of it done in Ford dealerships. This 5.4l engine is a poor design and should be recalled. It has numerous problems. I had a safety inspection done at a Ford dealership and it passed even though it had a ticking sound in the… Read more
I purchased my 2005 f150 with a 5.4l trinitron engine used in 2010. I completed all regular scheduled maintenance using the recommended products, most of it done in Ford dealerships. This 5.4l engine is a poor design and should be recalled. It has numerous problems. I had a safety inspection done at a Ford dealership and it passed even though it had a ticking sound in the engine and I had hesitation and loss of power. Replace spark plugs, I had already replaced the transmission at 98,000 miles! This engine is a piece of junk! Ford needs to stand behind its' "built Ford tough" trucks and make this right. I cant enjoy my truck!!!
Brake warning light is lit on the dashboard. There is nothing wrong with the brakes. I have read that there is a wiring problem which causes the brake light to stay on. Ford has recalled other f150 model years but not 2005 f150s.
The warning light for brakes, on the dash, stays on all of the time.
I was starting the truck to leave a wal-mart parking lot and my left foot which was on the brake went all the way to the floor of the truck. I had no brakes. It was fortunate that I was stopped and not on the road with other cars or going down a steep hill. I had the auto shop tow the truck to the shop. They fixed two brake lines. Complete brake failure should not happen.
The vehicle has a removable rubber cover on the brake pedal which can come off during braking causing one's foot to come off the pedal. This is what happened causing me to hit the car in front of me as I was coming to a stop. *tr
Tl* the contact owns a 2005 Ford F-150. The contact stated that the driver started the vehicle and heard a popping noise. There was smoke seen rising from under the hood. The contact appeared on the scene to examine the vehicle and noticed that the power assist feature on the brakes was no longer functioning. The vehicle was then towed to an authorized dealer where the contact… Read more
Tl* the contact owns a 2005 Ford F-150. The contact stated that the driver started the vehicle and heard a popping noise. There was smoke seen rising from under the hood. The contact appeared on the scene to examine the vehicle and noticed that the power assist feature on the brakes was no longer functioning. The vehicle was then towed to an authorized dealer where the contact was informed that various hoses for the braking system failed. The manufacturer was notified and stated that the vehicle was previously repaired under the recall associated with NHTSA campaign id number 08v208000 (service brakes, hydraulic:power assist:vacuum:hoses, lines/piping, and fittings). The manufacturer would not honor the recall a second time. The vehicle was not repaired. The failure mileage was 95,173.
In a three car accident. The 1st car turned on their signal at the same time attempted to turn into their driveway, the 2nd car hit the 1st car from the rear, as my F-150 approached the 2nd vehicle, I applied the brakes to stop before colliding into 2nd vehicle and the brakes became soft and did not slow the F-150, the F-150 was traveling at well below the posted speed limit,… Read more
In a three car accident. The 1st car turned on their signal at the same time attempted to turn into their driveway, the 2nd car hit the 1st car from the rear, as my F-150 approached the 2nd vehicle, I applied the brakes to stop before colliding into 2nd vehicle and the brakes became soft and did not slow the F-150, the F-150 was traveling at well below the posted speed limit, air-bags did not deploy, there fore hitting the 2nd vehicle in the rear causing almost no damage to 2nd vehicle and causing an almost totaled front end to the F-150 with close to $13000 in damage to F-150. No major injuries were reported, only minor back pain to both persons in F-150 were concurred. *tr
Tl*the contact owns a 2005 Ford F-150. The contact stated that the brake pedal was to close to the gas pedal. The contact approached a red light, engaged the brake pedal and accelerator pedal simultaneously. The vehicle lunged forward just enough to hit the vehicle in front of him at 10 MPH. The current and failure mileages were 50,000. Updated 11/16/10. *lj
I was involved in an injury crash. I hit the brakes and there was no stopping the truck. I didn't get the truck stopped until about 100-150 feet past the crash scene. There were no skid marks at all. *tr
I was in an accident due to brake failure. I was traveling at approximately 25 MPH and approaching a stop light in moderate traffic. I had 80 ft to the vehicle in front of me and when I depressed my brake pedal it went 3/4 of the way to the floor and was vibrating as anti lock was engaged. I rapidly depressed the pedal again and the same occurred. On the third attempt the… Read more
I was in an accident due to brake failure. I was traveling at approximately 25 MPH and approaching a stop light in moderate traffic. I had 80 ft to the vehicle in front of me and when I depressed my brake pedal it went 3/4 of the way to the floor and was vibrating as anti lock was engaged. I rapidly depressed the pedal again and the same occurred. On the third attempt the brakes finally engaged but was to late to stop the vehicle as I was only 2 feet from the car in front of me resulting in a crash. My speed was reduced to 8-10mph upon impact. The smaller car in front of me was knocked into a third car stopped at the light. Damage occurred to the truck and the smaller car and very minor damage to the 3rd vehicle. The weather was sunny and the streets were completely dry. I could not get my vehicle stopped even with no load other than my passenger who is a witness to the incident. No injuries occurred in any of the three vehicles and no airbags were deployed. I am scared to death as I have owned the truck for 2 years and never had this happen in my life. The brakes worked perfectly immediately following the incident and the truck was taken to the Ford dealer where purchased new and all service records are at this dealer. They thoroughly inspected the entire system and found no issues. System check on all sensors,lines, rotors and pads were ok. Perfect working order ? *tr
Tl*the contact owns a 2005 Ford f150. While slowing down to a complete stop, the vehicle rapidly accelerated. The contact depressed the brake pedal again to make sure that she depressed the correct pedal, and the vehicle jerked, continued to accelerate, and the engine revved. The vehicle only stopped when the passenger placed the gear into park. The contact struck the… Read more
Tl*the contact owns a 2005 Ford f150. While slowing down to a complete stop, the vehicle rapidly accelerated. The contact depressed the brake pedal again to make sure that she depressed the correct pedal, and the vehicle jerked, continued to accelerate, and the engine revved. The vehicle only stopped when the passenger placed the gear into park. The contact struck the preceding vehicle and the bumper sustained minor damages. The contacts vehicle was towed to the dealer because she was afraid to drive it again. A police report was filed. She filed complaint number 0405860938 with Ford. She was informed that it would be at least two weeks before she would hear from their legal department. There is currently an open investigation number pe08001 (service brakes, hydraulic:power assist:vacuum. Service brakes, hydraulic:power assist:vacuum:hoses, lines/piping, and fittings). The current and failure mileages were 34,000. Updated 4/29/08 *cn the damage was minor. Updated 05/16/08
Tl*the contact owns a 2005 Ford F-150. While driving 50 MPH, the rear calipers froze. The wheels began smoking and the vehicle was taken to the dealer. They stated that there was a malfunction with the calipers. The dealer also discovered that an axle seal was leaking, which saturated the brake fuse for the emergency brake. The dealer replaced the seal and calipers and… Read more
Tl*the contact owns a 2005 Ford F-150. While driving 50 MPH, the rear calipers froze. The wheels began smoking and the vehicle was taken to the dealer. They stated that there was a malfunction with the calipers. The dealer also discovered that an axle seal was leaking, which saturated the brake fuse for the emergency brake. The dealer replaced the seal and calipers and turned down all four rotors on the vehicle, but did not replace the brake pads. The failure recurred and the dealer replaced the rear calipers, rear rotors, and brake pads. The contact wanted to charge him for the brake pads (parts, not labor). The current mileage was 29,250 and failure mileage was 12,500. Updated 4/2/08 *cn updated 04/02/08 *tr
While trying to stop my Ford F-150 truck, I was actually hitting the accelerator at the same time as I was pushing the brake pedal. I could not tell that it was happening until it was too late. As I pshed on the brake the truck did not seem to slow down nearly as fast as it should have, so I pushed harder on the brake and that did not seem to work properly, then I realized… Read more
While trying to stop my Ford F-150 truck, I was actually hitting the accelerator at the same time as I was pushing the brake pedal. I could not tell that it was happening until it was too late. As I pshed on the brake the truck did not seem to slow down nearly as fast as it should have, so I pushed harder on the brake and that did not seem to work properly, then I realized the right edge of my foot was actually depressing the accelerator, but you could not really feel it since it has very little resistance. When I realized what was happening, I tried to lift my foot off the accelrator, but to do so I had to release the brake a bit. When I did that, the vehicle lurched forward toward the car in front of me and hit it. It happens because as you are hitting the accelerator while trying to brake, the engine revs up to high rpm, as you try to get your foot off the accelerator, and release the brake a bit, the car thinks you want to go fast and takes off because of the high rpm. This happened to me about two or three weeks ago, but it just seemed like an oddity at the time so I did not really think it was a big deal. Then it happened to me again yesterday when I needed to stop quickly because everyone had slammed on the brakes in front of me, so when I went to hit my brakes, I inadvertantly was hitting the accelerator at the same time again, only this time, it caused an accident as I plowed into the car in front of me. I had plenty of room in front of me, at least 10 to 1
Dt*: the contact stated while on a hill applying brake pressure at 8mph , the brake pedal dropped to the floorboard and there was a loss of all braking power. The vehicle was placed in neutral which allowed the vehicle to roll downhill and strike a fence. The seatbelt was worn and no injuries were sustained. However, the was minor damage to the vehicle. The police was not… Read more
Dt*: the contact stated while on a hill applying brake pressure at 8mph , the brake pedal dropped to the floorboard and there was a loss of all braking power. The vehicle was placed in neutral which allowed the vehicle to roll downhill and strike a fence. The seatbelt was worn and no injuries were sustained. However, the was minor damage to the vehicle. The police was not alerted. The vehicle was towed to the dealer who determined the master cylinder was inoperative. The master cylinder replacement corrected the braking problem. The manufacturer was not alerted.
The accident happened december 19, 2005: cause: brake failure. We were stopped at a red light and I was holding pressure on the brake pedal when it collapsed to the floor and rolled in to the car in front of us. At that time there was only 2000 miles on the pick-up. I wasn't sure what happened until we were at another stop light and it happened again, but this time I pumped… Read more
The accident happened december 19, 2005: cause: brake failure. We were stopped at a red light and I was holding pressure on the brake pedal when it collapsed to the floor and rolled in to the car in front of us. At that time there was only 2000 miles on the pick-up. I wasn't sure what happened until we were at another stop light and it happened again, but this time I pumped the brake pedal until I had pressure. We returned home in march and I went to the dealer whom we purchased it from (valu Ford at elbow lake, minnesota) and told them of the problem. He tried it and said he could not find a problem. I got into the pick-up and showed him how the master cylinder collapses when pressure is held on it. He tried another pick-up same year and said that's the way its supposed to be??? I went to another Ford dealer in alexandria (juettner motors) and told him what happened and what I wanted done and they told me my insurance company should taken care of the problem and didn't even check the brakes. I have taken the pick-up to 5 different independent garages and they have all said the master cylinder should not collapse when pressure is held on the pedal. I went back to the dealer and ask if they could have a company tech explain to me why the master cylinder collapses when pressure is held on the pedal. I have heard nothing from them. I feel very strongly that Ford has a problem with their master cylinder and should be fixed. I complained to Ford again and ask them t
May 2, 2006 the accident happened december 19, 2005: cause: break failure. We were stop at a red light and I was holding pressure on the break pedal and it collapsed to the floor and rolling in to the car in front of us. At that time there was only 2000 miles on the pick-up. I wasn't sure what happened until we were at another stop… Read more
May 2, 2006 the accident happened december 19, 2005: cause: break failure. We were stop at a red light and I was holding pressure on the break pedal and it collapsed to the floor and rolling in to the car in front of us. At that time there was only 2000 miles on the pick-up. I wasn't sure what happened until we were at another stop light and it happened again, but this time I pumped the break pedal till I had pressure. We returned home in march and I went to the dealer whom we purchased it from (valu Ford at elbow lake, minnesota) and told them of the problem. He tried it and said he could not find a problem. I got into the pick-up and showed him how the master cylinder collapses when pressure is held on it. He tried another pick-up same year and said that??s the way its supposed to be??? I went to another Ford dealer in alexandria (juettner motors) and told him what happened and what I wanted done and they told me my insurance company should take care of the problem and didn't even check the breaks. I have taken the pick-up to 5 different independent garages and they have all said the master cylinder should not collapse when pressure is held on the pedal. I went back to the dealer and ask if they could have a company tech explain to me why the master cylinder collapses when pressure is held on the pedal. I have heard nothing from them. I feel very strongly that Ford has a problem with their master cylinder and shoul
Dt*: the contact stated while driving 10 MPH the brake pedal was depressed and the vehicle accelerated forward crashing into another vehicle. The vehicle was taken to the dealer where the problem could not be duplicated. No police report was filed however; a representative from the dmv filed a report. Update 5/2/2006 - *nm
Dt*: the contact stated after attempting to apply sudden brake pressure, the vehicle struck another vehicle in the rear resulting in minor damage. The brakes stopped the vehicle, however not before the point of impact. No injuries were sustained and the police were not notified. Afterwards, the contact discovered the brake pedal was too close to the accelerator pedal. It… Read more
Dt*: the contact stated after attempting to apply sudden brake pressure, the vehicle struck another vehicle in the rear resulting in minor damage. The brakes stopped the vehicle, however not before the point of impact. No injuries were sustained and the police were not notified. Afterwards, the contact discovered the brake pedal was too close to the accelerator pedal. It was suspected that due to the design this could be unsafe, although the placement of the accelerator pedal was not a factor in the accident. The dealer was notified. A manufacturer representative inspected the vehicle. It was determined the placement of the accelerator and brake pedal met federal motor vehicle safety standards and no corrections were made.
Dt: the contact stated while traveling on the highway going at 55 MPH the vehicle hit something in the middle of the highway with the left front tire. The brakes were applied but they did not work. The consumer then lost control of the vehicle. The vehicle traveled into the median and collided with the retaining wall. This was a frontal impact. The seat belts failed to… Read more
Dt: the contact stated while traveling on the highway going at 55 MPH the vehicle hit something in the middle of the highway with the left front tire. The brakes were applied but they did not work. The consumer then lost control of the vehicle. The vehicle traveled into the median and collided with the retaining wall. This was a frontal impact. The seat belts failed to properly restrain the consumer and the air bags failed to deploy which resulted in injuries to the occupant. The vehicle was taken to an independent repair shop a couple of weeks prior to the accident for an ABS problem. They were unable to duplicate the problem with the brakes. *ak updated 1/25/2006. *nm