Feb 15, 2024power train
Rear driveshaft support failed while driving. A lot of smoke, noise and very bad vibration. Was traveling at a low speed(25mph). If the driveshaft had come apart, it could have easily caused damage to the body and its passengers. It also could've struck and damaged any vehicles near by. After speaking to the Ford dealer, they dais that it was a fairly common occurrence,… Read more
Rear driveshaft support failed while driving. A lot of smoke, noise and very bad vibration. Was traveling at a low speed(25mph). If the driveshaft had come apart, it could have easily caused damage to the body and its passengers. It also could've struck and damaged any vehicles near by. After speaking to the Ford dealer, they dais that it was a fairly common occurrence, which surprised me. Thanks for reading my complaint.
NHTSA complaint #11572216
Oct 24, 2023power train
The transmission randomly gets stuck in 1st gear and won’t shift beyond that. The rpms rev up real high and the only way to fix it is to pull off the road and turn the car off and back on. The transmission also bumps really hard shifting sometimes or revs up real high before shifting with a big thud. The dealership says they can’t diagnose it if it’s not doing it when I bring… Read more
The transmission randomly gets stuck in 1st gear and won’t shift beyond that. The rpms rev up real high and the only way to fix it is to pull off the road and turn the car off and back on. The transmission also bumps really hard shifting sometimes or revs up real high before shifting with a big thud. The dealership says they can’t diagnose it if it’s not doing it when I bring it in. They said the same thing about my alternator when it kept going out on me driving. They never could get it to mess up when they had it.
NHTSA complaint #11551670
Oct 19, 2023suspension, power train
The contact owned a 2008 Ford Edge. The contact stated that the while driving at an undisclosed speed, the vehicle inadvertently vibrated and jumped. No warning light was illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the passenger’s side cv axle seal and lower ball joint failed and needed to be replaced. The vehicle was repaired;… Read more
The contact owned a 2008 Ford Edge. The contact stated that the while driving at an undisclosed speed, the vehicle inadvertently vibrated and jumped. No warning light was illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the passenger’s side cv axle seal and lower ball joint failed and needed to be replaced. The vehicle was repaired; however, the failure recurred. The contact was informed that the parts to do the repair had failed. The dealer was not notified of the failure. The manufacturer was notified of the failure and the contact was informed that the repair required an unknown kit. The failure mileage was unavailable.
NHTSA complaint #11550863
Oct 5, 2023power train, exterior lighting, service brakes
Vehicle hard steering when drove Ford-from lot- always something wrong with brakes-wheel bearings- wheels- alignment electrical lightning for entire vehicle- sunroof also included in malfunctions *main safety concern front end / tranny grinding amongst other noises
NHTSA complaint #11548379
Oct 25, 2022power train
The contact owns a 2008 Ford Edge. The contact stated while approaching a stop sign, the vehicle lost motive power and stalled without warning. The contact was able to pull over on the side of the road, but the vehicle would not restart. The vehicle was towed to the dealer for diagnostic testing, but no failure was found. The contact stated that the failure persisted. On… Read more
The contact owns a 2008 Ford Edge. The contact stated while approaching a stop sign, the vehicle lost motive power and stalled without warning. The contact was able to pull over on the side of the road, but the vehicle would not restart. The vehicle was towed to the dealer for diagnostic testing, but no failure was found. The contact stated that the failure persisted. On another occasion, while driving, the vehicle experienced hard shifting to 2nd gear and a delay in upshifting to the next gear. The manufacturer was contacted and stated there was no recall on the vehicle for the failure and advised the contact to file a complaint with the NHTSA hotline. The approximate failure mileage was 120,000.
NHTSA complaint #11490864
Oct 19, 2022power train
Transmission slipping like all the other complaints, should be a recall for sure after looking through all the same issues in this year of Ford Edge around 78k miles.
NHTSA complaint #11489993
Apr 21, 2022power train
I own a 2008 Ford Edge awd limited and yesterday while getting on the interstate my vehicle made a loud clunking sound I immediately pulled over I had it towed to the house and once it was evaluated we discovered that there was a crack in the transmission housing there was no prior signs of the problem when we started the vehicle and put it in reverse it wouldn't move killed… Read more
I own a 2008 Ford Edge awd limited and yesterday while getting on the interstate my vehicle made a loud clunking sound I immediately pulled over I had it towed to the house and once it was evaluated we discovered that there was a crack in the transmission housing there was no prior signs of the problem when we started the vehicle and put it in reverse it wouldn't move killed the vehicle started back and put it in reverse and it moved but I will have to change the housing if not the whole transmission
NHTSA complaint #11461584
Jun 22, 2021power train, engineFire
The contact owns a 2008 Ford Edge. The contact stated that while driving at various speeds the vehicle would not properly accelerate and the engine would misfire. Also on occasions, the check engine light had illuminated and the speed would not increase past 10 MPH. The vehicle was taken to the local dealer who diagnosed that the input-out sensor in the transmission was faulty… Read more
The contact owns a 2008 Ford Edge. The contact stated that while driving at various speeds the vehicle would not properly accelerate and the engine would misfire. Also on occasions, the check engine light had illuminated and the speed would not increase past 10 MPH. The vehicle was taken to the local dealer who diagnosed that the input-out sensor in the transmission was faulty causing the ignition coil to melt. The contact indicated that the PCM was also faulty. The vehicle was repaired but the failures continued to occur. The manufacturer was notified of the failure. The failure mileage was 50,000.
NHTSA complaint #11421818
Apr 27, 2021power train, vehicle speed control, engine
Here we are years later and still the same issues....loss of power without warning, shuts off with no warning. Bangs when shifting, very rough shifting. Feels like its in 1st gear and then shifts roughly into gear, or I have to stop shut it off and start again. I see alot of the same complaint and no recall? Its gettin stupid now! This should be recalled, it is a safety issue!
NHTSA complaint #11414086
Mar 1, 2021power train, unknown or other, engine
Vehicle stalled while reversing into a parking spot. Barely started. Stalled a few seconds later after completing the reverse into parking spot. Barely started again. Got on the road and driving fine a few hundred feet, vehicle stalled almost ran into a group of parked vehicles. Barely started again. Made it to the highway to go home and while driving at just under 55mph limit… Read more
Vehicle stalled while reversing into a parking spot. Barely started. Stalled a few seconds later after completing the reverse into parking spot. Barely started again. Got on the road and driving fine a few hundred feet, vehicle stalled almost ran into a group of parked vehicles. Barely started again. Made it to the highway to go home and while driving at just under 55mph limit vehicle stalls in the passing lane. Almost caused a wreck with several vehicles including a semi. Didn't start for a few minutes. Vehicle stuttered to start and barely turned over. After it started I sat there and watched the tachometer, it would, without myself touching or doing anything, idle then jump a little and dip a little over and over. There seems to be no certain situation or reasoning for when, where or why it would stall, complete randomness! Highway driving, slow stop and go city driving, reversing, it seems to do it completely randomly and unexpectedly but always while moving one direction or the other. Straight line, turning, fast, slow, didn't make a difference. Finally was able to get off the highway, came into town and I was able to stop at all the lights and go but then out of no where again doing close to the 35mph limit it stalls again and this time I was at a 6 way intersection and almost hit another moving vehicle. My family will not be riding in this vehicle again until something is done! This is not normal or safe! Not for me or anyone else on the roadway! I have no clue as to w
NHTSA complaint #11398586
Feb 3, 2021power train
Transmission not shifting properly hesitated in shifting
NHTSA complaint #11394534
Jan 14, 2021power train, vehicle speed control
While driving on the highway the speedometer drops to 0, wrench light and airbag light turns on. Car losses power and keeps running. To move at all requires reving the engine to very high rpms
NHTSA complaint #11388228
Jun 7, 2020power train
On june 3, 2020 my 2008 Ford Edge experienced sudden transmission failure while driving on a busy 5 lane highway which could have resulted in injury or death. Thankfully, my wife was able to get it off the roadway. It was then towed to a repair shop. There were no warning signs leading up to this transmission failure. The car was well maintained primarily through a Ford… Read more
On june 3, 2020 my 2008 Ford Edge experienced sudden transmission failure while driving on a busy 5 lane highway which could have resulted in injury or death. Thankfully, my wife was able to get it off the roadway. It was then towed to a repair shop. There were no warning signs leading up to this transmission failure. The car was well maintained primarily through a Ford dealership and certified mechanics. The vehicle has only 96000 original miles. After a short internet search, it became painfully obvious that this was a well documented shortcoming of the 2008 Ford Edge. I contacted the local Ford dealership who verified that they were aware of this issue with the 2008 Edge, "but Ford has not recalled it yet". I then contacted Ford motor company on june 5th who also admitted that they were aware of sudden transmission failure in the 2008 Edge but have not recalled them as of this time. This is a serious, potentially life threatening manufacture defect that is being ignored by the Ford motor company. It is also costly to the consumer. Estimated cost to repair this through Ford with a rebuilt transmission is over $5000. Prior to this episode, we were pleased with this vehicle. However, we now question the moral decision making by Ford motor company in choosing to ignore this potential life threatening manufacture defect. I suggest that there be an immediate recall and reimbursement to customers for transmission failure in the 2008 Ford Edge.
NHTSA complaint #11327674
Jun 3, 2020power train, electrical system
The mechanic said the transmission and transfer case exploded costing me over $2,000 in repairs. The AC quit costing around $700 in repairs. The cd/radio has an electrical issue that has not been fixed because I can't afford it estimated at another$700 in repairs. *tr
NHTSA complaint #11327050
May 7, 2020steering, power train, service brakes
Right after I purchased this vehicle, I noticed that it had a bad jerk, and chugging in the transmission. With the overdrive "off", it keeps the rpm's above 2000, and prevents it from chugging and jerking in the transmission. With the overdrive on it gears down extremely low after going down to 2000 rpm's, and losses a lot of power. When pressing down the gas pedal, it chugs… Read more
Right after I purchased this vehicle, I noticed that it had a bad jerk, and chugging in the transmission. With the overdrive "off", it keeps the rpm's above 2000, and prevents it from chugging and jerking in the transmission. With the overdrive on it gears down extremely low after going down to 2000 rpm's, and losses a lot of power. When pressing down the gas pedal, it chugs and jerks severely. I have to let off the gas and then reapply the gas to stop it from jerking. Also, the power steering pops and makes noises. I got in the car today and had no brake power at all. Then had no brakes unless I pushed the brake pedal down with extreme force. And it was still extremely hard to stop my vehicle. Upon searching online, I am finding that these are very common issues with the 2008 Ford Edge vehicles. There should be some type of recall on this model of Ford Edge when this is a very common problem, in my opinion. I did a search for my VIN number and it shows "no" recalls for my vehicle. I understand it'd not a new vehicle, but the amount of issues with this vehicle is ridiculous. Please help!!! *tr
NHTSA complaint #11323604
Apr 20, 2020power train, vehicle speed control, electronic stability control (esc)
Speedometer dropped to 0 wrench light came on car had almost no power made loud noise then airbag light came on and tire pressure warning.
NHTSA complaint #11321694
Mar 27, 2020power train
When driving this the tool light engine light comes on loose the odometer and it doesn't want to move once you stop. Then when you can get it to move the transmission clunks hard . I also lost the mileage on the dash as well. And then when trying to pull into somewhere that has a slight hill the car won't go forward. This has been happening for a couple weeks
NHTSA complaint #11319539
Feb 20, 2020power train
I was driving on the highway and my car just stopped. Odo error came on. Pressed gas pedal and nothing. I could have been in a serious accident. At dealership now.
NHTSA complaint #11310293
Dec 7, 2019power train, electrical system, unknown or other
Battery light stayed on during a 4.5 hour trip. After reaching the end of the trip, the battery cables were found to be corroded. Noticed theterminal protector has melted. Used distilled water to fill the acid level in the battery, some was spilled on the positive battery cable connection(from battery to power of underhood fuse box), it sizzled from being hot! After filling… Read more
Battery light stayed on during a 4.5 hour trip. After reaching the end of the trip, the battery cables were found to be corroded. Noticed theterminal protector has melted. Used distilled water to fill the acid level in the battery, some was spilled on the positive battery cable connection(from battery to power of underhood fuse box), it sizzled from being hot! After filling the battery, the batt. Light stayed off for another 3 hours of trip, and lit up again. Had the battery tested, battery was found to be defective. R&r the battery, battery light is on again. No driveability issues, just concerned about, what is causing resistance in electrical charging system, and possible "fire"!
NHTSA complaint #11287652
Nov 20, 2019power train
When driving the vehicle it loses the ability to accelerate and only allows me to try to pull off the road to a safe place with the momentum of the vehicle before it lost power. If I am not at a place where I can immediately pull off safely I am stranded in traffic. When this occurs I am able to turn off my vehicle for a short period of time and when I restart it, the vehicle… Read more
When driving the vehicle it loses the ability to accelerate and only allows me to try to pull off the road to a safe place with the momentum of the vehicle before it lost power. If I am not at a place where I can immediately pull off safely I am stranded in traffic. When this occurs I am able to turn off my vehicle for a short period of time and when I restart it, the vehicle resumes normal operation until this happens again. It has happened in various weather conditions and at various speeds. When the acceleration is lost the powertrain fault light comes on.
NHTSA complaint #11281395
Oct 25, 2019power train, electrical system
2008 Ford Edge sel....with 6f50 transmission....165000 miles.... Vehicle shifts externally hard from 3rd to 4th gear with a hard jerk and load klunk, so much so that it has started causing me neck problems from tensing up in anticipation of the jerk. Also 2 twice up going from park to drive, had an extremly load noise in transmission that shook the entire vehicle and as I… Read more
2008 Ford Edge sel....with 6f50 transmission....165000 miles.... Vehicle shifts externally hard from 3rd to 4th gear with a hard jerk and load klunk, so much so that it has started causing me neck problems from tensing up in anticipation of the jerk. Also 2 twice up going from park to drive, had an extremly load noise in transmission that shook the entire vehicle and as I attempted to accelerate the rpm rose but the car barely eased forward and the transmission sounded as though it were in a bind. I then put it in park, turned the ignition off, pulled out the key, open and shut the door as to pretend I was exiting, then put key back into ignition, started the car, put it in gear (no problem) and accelerated as normal (no problem), except when it shifted from 3rd to 4th which is around 25mph. I have not and do not have any lights on in the instrument display panel nor do I have any error codes showing. Macanic says it would be an expensive shot in the dark to start randomly changing out sensors and changing out transmission would not solve the problem as it is not an issue with the mechanics of the transmission but an electrical issue. I've also tried a hard reboot to the cars electrical system to possibly clear any stored electrical issues, problem still exists!!! Definitely a recall needed, due to safety issues while driving and physical conditions that could arise from the tensing up in expectation of the hard jerk......
NHTSA complaint #11270966
Oct 11, 2019power train, vehicle speed control
The information panel lit up with the check engine light, the wrench, the airbag light, the tire pressure light and displayed a message: odo data error. The odometer/speedometer fell to zero. I stopped at a light and the vehicle would not accelerate normally, then a big clunking sound and finally moved forward. After a night in the garage, the vehicle drove normally the next… Read more
The information panel lit up with the check engine light, the wrench, the airbag light, the tire pressure light and displayed a message: odo data error. The odometer/speedometer fell to zero. I stopped at a light and the vehicle would not accelerate normally, then a big clunking sound and finally moved forward. After a night in the garage, the vehicle drove normally the next day and all the warning lights were off. Then one day it happened again. Took it to a Ford dealership. They said they could not duplicate the problem and therefore couldn't find anything to fix. Since that time, it has happened several times and each time I pull off the road, turn the engine off, wait a little bit, start the engine again and pull away. There is always the clunking and jerking into gear. After reviewing a few Ford online forms, I see that this is a common problem in the 2008 Edge and may be attributed to two sensors, the speed output and turbine sensors. For safety reasons, I will only drive on surface streets because I never know when it's going to happen. Seems to me, Ford is likely aware of this and would be a shame if someone got hurt. The date below is the most recent occurrence although it has happened several times. *tr
NHTSA complaint #11268005
Sep 16, 2019power train, vehicle speed control
Start engine, move transmission into reverse, transmission clunks loudly. When transmission is moved to drive, engine revs high, barely moves forward, speedometer stuck at zero despite moving up to 20mph. Engine light comes on, airbag light comes on.
NHTSA complaint #11255657
Sep 8, 2019power train
Driving down the road and the wrench light comes on, speedometer stops working and the vehicle loses power. I can also smell a burning smell. Once I have come to a stop, the transmission shifts very hard like someone has hit the vehicle. This has happened several times, including a couple of times when I pulled into traffic and the vehicle lost power, coming very close to… Read more
Driving down the road and the wrench light comes on, speedometer stops working and the vehicle loses power. I can also smell a burning smell. Once I have come to a stop, the transmission shifts very hard like someone has hit the vehicle. This has happened several times, including a couple of times when I pulled into traffic and the vehicle lost power, coming very close to causing an accident with oncoming traffic. Very dangerous and I am very apprehensive about driving the car due to my family's safety.
NHTSA complaint #11254007
Aug 20, 2019power train, electronic stability control (esc)
"takata recall" I was driving my child to school in highway traffic, speeds of 55 MPH. The car mileage indicators went blank, a wrench light came on and all power to car was lost during turning a curve on highway.vehicle started making very loud popping noise and jerking the car. Turned car off after coming to a stop, restarted car, no warning lights, everything was normal… Read more
"takata recall" I was driving my child to school in highway traffic, speeds of 55 MPH. The car mileage indicators went blank, a wrench light came on and all power to car was lost during turning a curve on highway.vehicle started making very loud popping noise and jerking the car. Turned car off after coming to a stop, restarted car, no warning lights, everything was normal except, when starting car, it made very loud noise as it was started, then as I placed in drive or reverse it moved the vehicle jerking an loud popping noise. The entire motor moved sideways when placed in gear an hood up. Also now it no longer works in low gear. Once placed on machine it gave code po720-722
NHTSA complaint #11245186
Aug 6, 2019power train, vehicle speed control, engine
The wrench light will come on when driving the vehicle, and power is lost. My car will slow down to around 10-20 MPH no matter where I am or how fast I am going. This is a huge safety issue that needs to be addressed by Ford. I have been on I-10 with my husband and toddler and the vehicle goes into this "limp mode" at 80 MPH! I am so terrified to drive a vehicle that I have to… Read more
The wrench light will come on when driving the vehicle, and power is lost. My car will slow down to around 10-20 MPH no matter where I am or how fast I am going. This is a huge safety issue that needs to be addressed by Ford. I have been on I-10 with my husband and toddler and the vehicle goes into this "limp mode" at 80 MPH! I am so terrified to drive a vehicle that I have to pay every month for. Mechanics that have looked at the car have no definitive answer to problem, they suggested that the throttle body be cleaned. We did that and it was no help. The vehicle left me and my son stranded this morning on the side of the highway because I could not get it out of the "safety limp mode". Usually, I can pull over, park, and shut the car off for a few minutes, then turn it on and it would work again. This morning, it would not reset itself. I would appreciate any help or advice on this matter.
NHTSA complaint #11241933
Jul 20, 2019power train
2008 Ford Edge while driving on city streets all of a sudden the wrench light came on, airbag light, the mileage odometer blanked out and the speedometer stopped working there was a loss of power. The transmission makes a huge clunking sound and jerks into gear shifting into drive from park and reverse
NHTSA complaint #11233521
Jul 12, 2019power train
While normally driving, the "wrench" light will come on and the vehicle goes into a low-power "limp mode". So I pull over immediately, and put the vehicle in park, shut it off, and remove the key. I sit with it powered off for about a 10 second count, and restart the engine. The wrench light goes off, and I can drive normally until it happens again.
NHTSA complaint #11231261
Jun 14, 2019power train
Vehicle in motion on city road when vehicle all of a sudden makes loud/hard clank noise and immediately loses power - almost like it started towing a trailer! Loss of power, wrench light, tps light, airbag light all come on, speedometer stops working. Pulled over, loud/hard clank sound with every gear change p-2. Vehicle had displayed no issues prior to this. Dropped vehicle… Read more
Vehicle in motion on city road when vehicle all of a sudden makes loud/hard clank noise and immediately loses power - almost like it started towing a trailer! Loss of power, wrench light, tps light, airbag light all come on, speedometer stops working. Pulled over, loud/hard clank sound with every gear change p-2. Vehicle had displayed no issues prior to this. Dropped vehicle off at mechanic, when he looked at it next morning, vehicle is running perfect. Today is a friday, I was supposed to go out of town (via i75) but I am going to stay local as it does not feel safe to drive on the highway. I am greatly concerned about what appears to be a huge safety issue with this car. All you have to do is search - there are multiple complaints about the same issue to be found all over the internet with no fixes known. Ford needs to issue a recall and fix this asap before someone gets seriously hurt or is killed from the extreme loss of power the vehicle is suffering from when this happens.
NHTSA complaint #11219989
Jun 12, 2019power train, vehicle speed control, engine
Driving, going up a hill, the car stopped accelerating and lost power going up. I almost got into an accident. The car doesn't accelerate and it has all the fluids and changed of oils. The car clunks and has a wrench. When I put into reverse it jump a very minimum acceleration. I'm afraid to drive it. I had to tow the car. The mechanic couldn't find the problem. He said he… Read more
Driving, going up a hill, the car stopped accelerating and lost power going up. I almost got into an accident. The car doesn't accelerate and it has all the fluids and changed of oils. The car clunks and has a wrench. When I put into reverse it jump a very minimum acceleration. I'm afraid to drive it. I had to tow the car. The mechanic couldn't find the problem. He said he cleared up the computer and it was fine. Then I was driving on the highway and it happened again. No acceleration. Why Ford hasn't made this into a safety recall. I did my investigation and I believe it has to do with the transmission sensors. Please help me.
NHTSA complaint #11219565
Jun 6, 2019power train, electrical system, vehicle speed control
I own a 2008 Ford Edge limited I am having the same problem as some people on here are with the wrench 🔧 light also a air bag light comes on and I have almost had an accident because the car speedometer stops working and the car shifts super hard it seems to be happening more frequently I did my research on fords website for finding out the problem and it's a glitch… Read more
I own a 2008 Ford Edge limited I am having the same problem as some people on here are with the wrench 🔧 light also a air bag light comes on and I have almost had an accident because the car speedometer stops working and the car shifts super hard it seems to be happening more frequently I did my research on fords website for finding out the problem and it's a glitch this is a huge safety concern when trying to avoid an accident from occurring also you can't even view the speed I think this should be investigated and recalled because I it can create a unsafe environment to not only my vehicle but others as well.
NHTSA complaint #11218388
May 17, 2019power train
Transmission slipping and downshifting hard - around 80,000k I started to notice that the transmission would bang when I put it in reverse. After that, other issues started happening - while pressing the gas pedal, vehicle would not switch to a higher gear. I'd have to come to a complete stop (in traffic!), put it in park, then try to drive again. Periods when the vehicle… Read more
Transmission slipping and downshifting hard - around 80,000k I started to notice that the transmission would bang when I put it in reverse. After that, other issues started happening - while pressing the gas pedal, vehicle would not switch to a higher gear. I'd have to come to a complete stop (in traffic!), put it in park, then try to drive again. Periods when the vehicle would get to speed then slip. Transmission would bang like I was being rear-ended. Changed the valve body, tss, and oss sensors. That worked for a while but now it's acting up again. Downshifts so hard and bangs while I'm driving at various speeds. I'm afraid it's going to go completely while I'm driving. There was no prior damage to vehicle to cause this malfunction.
NHTSA complaint #11208299
May 8, 2019power train, vehicle speed control
On 4/26/19 the Ford Edge was setting in park letting my sisters get out the Ford Edge was put in drive it would not move put it in reverse it would not move, turn it off and on again it started to work fine.I do not what is going on it
NHTSA complaint #11206362
Apr 28, 2019power train, vehicle speed control
While driving in the city it jump from first to second gear with a hard boom. Driving on the highway while going up a hill jump out of gear and will not pull I pull over to the shoulder. To get the car to function again I have to turn the Ford Edge off turn it back on this is not good. What can be done to fix the problem. *tr
NHTSA complaint #11204228
Apr 10, 2019power train, electrical system
While driving down the road, the odometer suddenly drops to zero while still moving at the posted speed limit. The wrench symbol warning light in the dash comes on, as well as the airbag light. The mileage is then cleared, and the dash reads "odo error". Pulled over, turned off the vehicle and removed the key from the ignition. Go to turn the vehicle back on, car starts… Read more
While driving down the road, the odometer suddenly drops to zero while still moving at the posted speed limit. The wrench symbol warning light in the dash comes on, as well as the airbag light. The mileage is then cleared, and the dash reads "odo error". Pulled over, turned off the vehicle and removed the key from the ignition. Go to turn the vehicle back on, car starts normally, all the warning lights are cleared. Put the vehicle into reverse, and hear and feel a loud "clunk" as the vehicle shifts, and am able to back up normally. When shifting back into drive, the rpms jump up, the car shifts and makes the loud "clunk", and when pushing the accelerator, the vehicle barely moves. It will occasionally come back and the vehicle will return to it's normal running state, but then it will eventually returned to the defective state. No odometer while driving, no power if you stop leaving you stranded.
NHTSA complaint #11195509
Mar 31, 2019power train
As everyone else with 08 Edge the transmission loses power. Entering hwy and press on gas, no pickup just stalls out. Reported to energy country Ford on 3 different visits, in port arthur, tx and of course they said nothing wrong. Also, loud clunk from park to reverse or drive. Paint also chips/peels on this cream colored vehicle. Have seen other vehicles this color on the… Read more
As everyone else with 08 Edge the transmission loses power. Entering hwy and press on gas, no pickup just stalls out. Reported to energy country Ford on 3 different visits, in port arthur, tx and of course they said nothing wrong. Also, loud clunk from park to reverse or drive. Paint also chips/peels on this cream colored vehicle. Have seen other vehicles this color on the road and the paint around door areas peeling. Only 65k miles and well maintained. With so many reports of this issue Ford surely would recall the 08 Edge transmission like they have on the trucks.
NHTSA complaint #11192718
Feb 27, 2019power train, vehicle speed control
I was driving in a city street and my car suddenly had very decreased power and the wrench light came on. I drove until I found a place to safely pull over to the side of the road. When I turn the car off and back on the light turns off.
NHTSA complaint #11182694
Jan 22, 2019power train, vehicle speed control
Tl* the contact owns a 2008 Ford Edge. While driving 70 MPH, the check engine and air bag warning indicators illuminated. Also, the odometer became inoperable and the vehicle failed to maintain forward momentum. The vehicle was safely guided off of the roadway, the ignition was placed in the off position, and the vehicle was restarted; however, it failed to accelerate. The… Read more
Tl* the contact owns a 2008 Ford Edge. While driving 70 MPH, the check engine and air bag warning indicators illuminated. Also, the odometer became inoperable and the vehicle failed to maintain forward momentum. The vehicle was safely guided off of the roadway, the ignition was placed in the off position, and the vehicle was restarted; however, it failed to accelerate. The vehicle was not diagnosed or repaired. Krause family Ford of woodstock (located at 195 woodstock pkwy, woodstock, ga 30188, (770) 592-8873) and the manufacturer were contacted. The approximate failure mileage was 159,000. *tt vehicle was repaired.*jb
NHTSA complaint #11171307
Dec 28, 2018power train
While driving through an intersection at approx 40 MPH transmission shutter and locked the wheels up. Luckily the traffic around me was able to dodge me without incident. I shut it off and restarted put into 1st gear and pulled off to side of road. There was burnt gear oil smell coming from under the suv. Now it comes and goes trans slipping and ptu overheating.
NHTSA complaint #11163784
Nov 27, 2018power train
Bought car used july 2017 from a dealer. Has problems starting a few weeks after purchase of not wanting to move. If in heavy traffic doing 5-10 MPH on expressway, when traffic finally breaks car will not move, rpm's go up but transmission is still stuck. This is a safety issue that really needs to be addressed as I am seeing a lot of complaints for the same thing. Took my car… Read more
Bought car used july 2017 from a dealer. Has problems starting a few weeks after purchase of not wanting to move. If in heavy traffic doing 5-10 MPH on expressway, when traffic finally breaks car will not move, rpm's go up but transmission is still stuck. This is a safety issue that really needs to be addressed as I am seeing a lot of complaints for the same thing. Took my car into the dealer due to extended warranty. They were able to replicate what I told them. This is an internal part failure but I am still waiting to hear if my extended warranty will be paying for this. Unacceptable that so many have this serious issue which could cause an accident if car does not move on a busy highway or at a stop light. This has happened in heavy stop/go traffic, from a stop light when light changes to green. Unless you can find a way to pull off and turn the car off and back on it will not move.
NHTSA complaint #11154362