CarProblemsDB

2005 Ford Crown Victoria engine problems

11 owners reported engine & cooling problems — 6% of all 193 complaints about the 2005 Ford Crown Victoria.

Engine & cooling complaints by Ford Crown Victoria year

20113
20092
20082
20078
20063
200511
200410
200313
20028
200111
200021

What owners report

Jan 19, 2022structure, wheels, engine

Unknown the ride feels unsafe to travel around inn

NHTSA complaint #11447986
Jun 19, 2017power train, engine

Loss of acceleration at wide open throttle, transmission seems to "slip" when trying to pass or accelerate hard at highway speed has happened on multiple occasions

NHTSA complaint #11000031
Apr 7, 2016engineFire
The spark plugs have been ejecting themselves from the engine, taking part of the cylinder head with them making repairs dangerous and costly. Sometimes the spark plug stays attached to the coil, causing fuel vapors to ignote, but most of the time they rip the coil pack and boot out with them. This has happened four times with my last Crown Victoria and twice with my current… Read more

The spark plugs have been ejecting themselves from the engine, taking part of the cylinder head with them making repairs dangerous and costly. Sometimes the spark plug stays attached to the coil, causing fuel vapors to ignote, but most of the time they rip the coil pack and boot out with them. This has happened four times with my last Crown Victoria and twice with my current one. It always happens as the vehicle has been driving down the road, causing a dramatic loss of power and sometimes a fire.

NHTSA complaint #10854188
Nov 5, 2015engine

Tl* the contact owns a 2005 Ford Crown Victoria. While driving approximately 65 MPH, the vehicle stalled without warning. The vehicle was restarted. The contact discovered that the serpentine belt failed and was replaced. The failure recurred. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 104,000.

NHTSA complaint #10788531
Feb 2, 2015engine

At first the car would slip into neutral instead of going into 2nd gear so I had to turn od off now the car want go into drive at all. I see on the internet that this has a lot of complaints. *tr

NHTSA complaint #10680455
Jul 23, 2014steering, engine
I was responding as a volunteer ambulance emt from my residence to the fire station for an emergency call when the steering locked up. I tried to turn the steering wheel back and forth while applying the brakes and it began to steer again. I continued to the station about 3/4 mile away, made the ambulance call. Upon completion of the call I lifted the hood and observed the… Read more

I was responding as a volunteer ambulance emt from my residence to the fire station for an emergency call when the steering locked up. I tried to turn the steering wheel back and forth while applying the brakes and it began to steer again. I continued to the station about 3/4 mile away, made the ambulance call. Upon completion of the call I lifted the hood and observed the lower joints of the steering shaft were rusty and corroded. I sprayed the joint with wd-40 and turned the steering back and forth. In preparation for a trip two days later I was checking the vehicle and found the "exhaust heat shield" lying on the frame between the engine and frame. It was then I figured the part had come off and jammed between the steering shaft and the frame causing a momentary loss of steering control. I have not replaced the heat shield. After a factory recall replacement of the lower shaft resulted in the car steering like new with very little effort for a month or so. I then noticed the steering seemed to bind again at times. I looked and the upper steering shaft is corroded so I sprayed the u joint contained in the upper shaft with lubricant. I contacted the dealer who said the upper shaft was not part of the recall so I called Ford and was told the same thing. The upper shaft joint is experiencing the same failure as the lower shaft. Corrosion in the u joint is causing the needle bearings to not operate properly resulting in more difficult turning of the steering. I lubricate the j

NHTSA complaint #10615584
Nov 1, 2013power train, engine

Tl* the contact owns a 2005 Ford Crown Victoria. The contact stated while driving approximately 45 MPH the wrench warning symbol illuminated and the engine stalled. Upon restarting the vehicle it failed to accelerate over 5 MPH. The failure was repaired. The manufacturer was notified of the failure. The approximate failure mileage was 76,000. ..updated 02-28-14 *bf updated 03/19/2014 *js

NHTSA complaint #10550461
Aug 20, 2013seat belts, engineCrash2 injured

My wife died in this police car lost control due to engine jerking and seat belts came loose and ejected my daughters havin head injury concussion and broken skull. *tr

NHTSA complaint #10536369
Jul 15, 2011engine and engine cooling, vehicle speed control
Tl* the contact owns a 2005 Ford Crown Victoria. The contact stated that the engine exhibited an abnormally excessive increase in rpm's. The contact stated that he would have to depress the brakes hard so that the vehicle would not run away. The vehicle was taken to the dealer where they were unable to duplicate the failure. The manufacturer was contacted but offered no… Read more

Tl* the contact owns a 2005 Ford Crown Victoria. The contact stated that the engine exhibited an abnormally excessive increase in rpm's. The contact stated that he would have to depress the brakes hard so that the vehicle would not run away. The vehicle was taken to the dealer where they were unable to duplicate the failure. The manufacturer was contacted but offered no assistance. The failure mileage was 33,000. Updated 8/30/11 *cn the consumer stated while at a stop, with the engine running, he experienced a high engine acceleration without touching the accelerator pedal and the brakes would hardly hold the car in place. The consumer stated he would have to shut the engine off. Updated 09/21/11

NHTSA complaint #10412404
Sep 28, 2010engine and engine cooling

Catalytic converter rattles after 54,000 miles found Ford bulletin on problem. Should be replaced by Ford. *tr

NHTSA complaint #10358052
May 20, 2005steering, suspension, engine and engine cooling, fuel system, gasoline, exterior lighting

1995 Ford Crown Victoria [xxx] upper and lower ball joints needed to be replaced. Tie rod and pitman arm replaced. Gas tank leaks. Moisture on piston which threw a rod and broke block. Headlight lenses turned dark orange. *js information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)

NHTSA complaint #10121726
← All 2005 Ford Crown Victoria problems & recalls