Aug 28, 2026power train
The contact owns a 2010 Dodge RAM 1500. The contact stated while driving at an undisclosed speed, the driveshaft detached. No warning lights were illuminated. The contact received notification for NHTSA campaign number: 13v038000 (power train) however, the part to complete the recall repair was not yet available. The vehicle was towed to a dealer, where it was diagnosed that… Read more
The contact owns a 2010 Dodge RAM 1500. The contact stated while driving at an undisclosed speed, the driveshaft detached. No warning lights were illuminated. The contact received notification for NHTSA campaign number: 13v038000 (power train) however, the part to complete the recall repair was not yet available. The vehicle was towed to a dealer, where it was diagnosed that the rear axle pinion nut needed to be replaced. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 262,420.
NHTSA complaint #11760355
Nov 18, 2025power train
During unrelated work, a mechanic discovered the retaining ring for recall n08 (rear axle pinion nut) was not installed and the pinion nut was loose enough to turn by hand. He stated the recall had either been performed incorrectly or not at all, and that the vehicle was unsafe to drive. The recall shows “completed” in 2013, but the defect is still present. I contacted… Read more
During unrelated work, a mechanic discovered the retaining ring for recall n08 (rear axle pinion nut) was not installed and the pinion nut was loose enough to turn by hand. He stated the recall had either been performed incorrectly or not at all, and that the vehicle was unsafe to drive. The recall shows “completed” in 2013, but the defect is still present. I contacted stellantis customer care, submitted photos, and they confirmed in writing that if the defect still exists, the recall must be performed free of charge regardless of age, mileage, or ownership. I sent the photos of the missing ring, screenshots showing the recall marked completed, and stellantis’ confirmation to the dealership before having the vehicle towed to verify coverage. The truck was towed to time chrysler Dodge jeep ram of portland. My initial contact was [xxx] at that location. However, all recall decisions and communication later came from [xxx] , who works at a different dealership. Over the next month, the dealership repeatedly stalled the recall, saying they were waiting on approval from the district manager and then from the recall department, but no action was ever taken. Despite having stellantis’ written confirmation and clear photographic evidence of the unresolved defect, the dealership refused to perform the recall. They insisted on treating it as a “warranty” issue and cited reasons such as mileage, age, and not being the original owner—none of which apply to safety recalls. They then s
NHTSA complaint #11700012
Sep 15, 2025power train
2010 Dodge RAM 1500 truck purchased used late may 2025 with 57000 miles. Late august 2025 with 60000 miles rear axle fell off when driving on freeway at 60 miles per hour. Very serious accident was narrowly avoided as could not steer vehicle.truck was serviced at dealership for recall of a pinion nut coming loose at 36107 miles in september 2013. Per this recall, the loose… Read more
2010 Dodge RAM 1500 truck purchased used late may 2025 with 57000 miles. Late august 2025 with 60000 miles rear axle fell off when driving on freeway at 60 miles per hour. Very serious accident was narrowly avoided as could not steer vehicle.truck was serviced at dealership for recall of a pinion nut coming loose at 36107 miles in september 2013. Per this recall, the loose pinion nut can cause the axle to fail. The recall maintenance done in september 2013 at 36107 miles only lasted 24000 miles and serious safety issues reoccurred. In my opinion, on my vehicle the recall did not fix the problem. Now I am stuck with a $5000 repair on a vehicle with known recalls and safety issues that was supposedly fixed.perhaps a second recall should be considered regarding this issue.
NHTSA complaint #11687346
Aug 29, 2025suspension, power train, wheels
Me and my husband were driving down the road to go see a friend and all of a sudden the wheel hub assembly broke in half causing us to have to slam on our brakes and keep from crashing. The wheel almost ended up under our truck making the truck look like it was kachowing like lightening mcqueen from the movie cars
NHTSA complaint #11683820
May 28, 2025power train, unknown or otherCrash
I was driving to work on [xxx] when my rear end locked up and I slid sideways down [xxx]. I was going slower than normal due to slippery road conditions. The mechanic told me it was the pinion nut that froze up and locked up the gears and snapped the drive shaft. If it had been clear roads the truck probably would have flipped over. Information redacted pursuant to the… Read more
I was driving to work on [xxx] when my rear end locked up and I slid sideways down [xxx]. I was going slower than normal due to slippery road conditions. The mechanic told me it was the pinion nut that froze up and locked up the gears and snapped the drive shaft. If it had been clear roads the truck probably would have flipped over. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6)
NHTSA complaint #11663333
Apr 24, 2025power train
The contact owns a 2010 Dodge RAM 1500. The contact stated while driving at an undisclosed speed, there was an abnormally loud sound coming from the rear of the vehicle. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that the rear axle differential pin retaining bolt had failed and needed to be replaced. The vehicle was not repaired.… Read more
The contact owns a 2010 Dodge RAM 1500. The contact stated while driving at an undisclosed speed, there was an abnormally loud sound coming from the rear of the vehicle. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that the rear axle differential pin retaining bolt had failed and needed to be replaced. The vehicle was not repaired. The vehicle was taken to the dealer but was not yet diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 160,704.
NHTSA complaint #11656516
Oct 4, 2022power train, engine
The contact owns a 2010 Dodge RAM 1500. The contact stated that while driving at an unknown speed, the vehicle was jerking as the check engine warning light illuminated. The vehicle was taken to a local dealer where the contact was informed that the oxygen sensors and transmission fluid needed to be replaced. The vehicle was not repaired, however, the contact attempted to… Read more
The contact owns a 2010 Dodge RAM 1500. The contact stated that while driving at an unknown speed, the vehicle was jerking as the check engine warning light illuminated. The vehicle was taken to a local dealer where the contact was informed that the oxygen sensors and transmission fluid needed to be replaced. The vehicle was not repaired, however, the contact attempted to replace the oxygen sensors himself. The failure reoccurred and the vehicle was then taken to an independent mechanic, where it was diagnosed that the engine needed to be replaced. The vehicle was repaired and the proper oxygen sensors were replaced; however, the contact stated that when he drove over 45 MPH, all warning lights would illuminate on the instrument panel and that an abnormal noise was heard coming from the rear of the vehicle. The vehicle was then taken back to the independent mechanic where it was diagnosed that the transmission needed to be replaced. Additionally, during the repair the contact was informed that the rear differential had loose bolts and would also need to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure however the VIN was not available at the time of the call therefore a case could not be opened. The VIN was not available. The approximate failure mileage was 240,000.
NHTSA complaint #11487826
Sep 13, 2022power train, electrical system, engine
Charging system failure at PCM causing low voltage and battery will not charge causing the vehicle to become disabled. I was on the interstate battery light came om with system low voltage code for engine light. The truck shut off and I was left without power steering or brakes. Doing 75mph. Voltage regulator is in PCM and PCM needs replaced. Vehicle is still out of commission
NHTSA complaint #11484168
Jun 15, 2022power train, fuel system, gasoline
The contact owns a 2010 Dodge RAM 1500. The contact received notification of NHTSA campaign numbers: 13v038000 (power train), 18v160000 (fuel system, gasoline), and 17v821000 (power train). The contact stated that while driving at an undisclosed speed, the rear axle pinion holding the rear drive shaft loosened. The vehicle was taken to the dealer, and the dealer declined to… Read more
The contact owns a 2010 Dodge RAM 1500. The contact received notification of NHTSA campaign numbers: 13v038000 (power train), 18v160000 (fuel system, gasoline), and 17v821000 (power train). The contact stated that while driving at an undisclosed speed, the rear axle pinion holding the rear drive shaft loosened. The vehicle was taken to the dealer, and the dealer declined to honor the recall repairs due to the age of the vehicle and possible liability issues. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and a case was opened. The failure mileage was approximately 183,000.
NHTSA complaint #11469417
Apr 19, 2022power train
The vehicle was repaired under recall, but was not correctly fixed. Now the rear differential is totally shot with no warning. My dealer says it will not be covered under recall warranty since I was not the owner at the time of the recall repair.
NHTSA complaint #11461366
Jun 1, 2021power train
The contact owns a 2010 RAM 1500. The contact stated while driving 35 MPH, the driveshaft detached from the sub-frame of the vehicle. The contact pulled over and the vehicle was towed to an independent mechanic to be diagnosed. The contact was informed that the driveshaft needed to be replaced. There was no warning light illuminated. Upon investigation, the contact associated… Read more
The contact owns a 2010 RAM 1500. The contact stated while driving 35 MPH, the driveshaft detached from the sub-frame of the vehicle. The contact pulled over and the vehicle was towed to an independent mechanic to be diagnosed. The contact was informed that the driveshaft needed to be replaced. There was no warning light illuminated. Upon investigation, the contact associated the failure with NHTSA campaign number: 12v474000 (power train) however, the VIN was not included. The manufacturer was informed of the failure but provided no further assistance. The failure mileage was approximately 97,000.
NHTSA complaint #11419178
Jan 8, 2021steering, power train, unknown or other
Truck broke down when driving city street normal conditions. Drive shaft fell off and broke in two. Related to safety recall n08 - rear axle pinion nut opened april 2013. Extensive damage done to truck, $13k or so in parts alone or more than truck value. Had my truck since june 2020, just now informing me they will not cover any damages caused by the safety recall issue… Read more
Truck broke down when driving city street normal conditions. Drive shaft fell off and broke in two. Related to safety recall n08 - rear axle pinion nut opened april 2013. Extensive damage done to truck, $13k or so in parts alone or more than truck value. Had my truck since june 2020, just now informing me they will not cover any damages caused by the safety recall issue (only the recall repairs which is minimal). Do I have any recourse with chrysler? Are they correct in their handling or do they owe me some kind of fair settlement payout since the damages are worth more than the truck value (trade in around $12k).
NHTSA complaint #11387176
Sep 23, 2020power train
We have a 2010 Dodge RAM 1500 that was purchased used from a dealer on 8/15/19. VIN records indicate that recall work was performed in 2014 to secure the pinion nut. On 8/31/20, we were driving and heard a loud sound, our vehicle began to shake, fishtail and the rear end locked up causing us to come to a stop sideways across 2 lanes of traffic just missing hitting a… Read more
We have a 2010 Dodge RAM 1500 that was purchased used from a dealer on 8/15/19. VIN records indicate that recall work was performed in 2014 to secure the pinion nut. On 8/31/20, we were driving and heard a loud sound, our vehicle began to shake, fishtail and the rear end locked up causing us to come to a stop sideways across 2 lanes of traffic just missing hitting a pedistrian. The vehicle was towed to a mechanic whom after inspection stated there was no securement device in place which resulted in the pinion nut coming out causing our driveshaft to fall out and the rear end lock up.
NHTSA complaint #11360795
Sep 20, 2020power train
On 8/31/20 while driving on a city street (shortly after exiting the highway) we heard a loud sound, our vehicle began to shake, fishtail and the rear end locked up causing us to come to a stop sideways across two lanes of traffic. We barely missed hitting a pedistrian. The driveshaft had fallen out. After a mechanic inspection for repairs, we were told the pinion nut came… Read more
On 8/31/20 while driving on a city street (shortly after exiting the highway) we heard a loud sound, our vehicle began to shake, fishtail and the rear end locked up causing us to come to a stop sideways across two lanes of traffic. We barely missed hitting a pedistrian. The driveshaft had fallen out. After a mechanic inspection for repairs, we were told the pinion nut came out which caused the drive shaft to fall out and the rear end to lock up.*dt
NHTSA complaint #11360064
Jul 13, 2020power train
Around the 115,000 mile mark the rear differential started to make a weird noise when I wasn't actively accelerating. When I was coasting I could tell something was wrong with the rear end of my vehicle. The transmission shop I brought it to confirmed the rear differential bearings have gone bad. At only 115,000 thousands miles I thought this was a manufacturer issue and a… Read more
Around the 115,000 mile mark the rear differential started to make a weird noise when I wasn't actively accelerating. When I was coasting I could tell something was wrong with the rear end of my vehicle. The transmission shop I brought it to confirmed the rear differential bearings have gone bad. At only 115,000 thousands miles I thought this was a manufacturer issue and a safety issue. Anywhere from 10pmh or faster the grinding noise can be heard.
NHTSA complaint #11339074
Jun 27, 2020power trainCrash
Drove down the road and there was a humming sound from the rear end that progressively got louder then started to make a rattling shaking sound and leaking transmission fluid then when was driving down the road a loud bang and back wheels seized up completely which resulted in my swerving violently and ending up in a ditch. When I got out and looked the drive shaft was in the… Read more
Drove down the road and there was a humming sound from the rear end that progressively got louder then started to make a rattling shaking sound and leaking transmission fluid then when was driving down the road a loud bang and back wheels seized up completely which resulted in my swerving violently and ending up in a ditch. When I got out and looked the drive shaft was in the road. I had a tow truck tow it to my family's house where it still sits now but drive shaft is no where to be found. This all is found in recall n08
NHTSA complaint #11331179
Jun 8, 2020power train, electrical system, engine
Tl* the contact owns a 2010 RAM 1500. The contact stated that the vehicle failed to start after several attempts with several unknown warning lights illuminated. Additionally, on several occasions while driving at various speeds, the vehicle stalled without warning. The vehicle was taken to columbus chrysler Dodge jeep ram (2806 23rd st, columbus, ne 68601) where the vehicle… Read more
Tl* the contact owns a 2010 RAM 1500. The contact stated that the vehicle failed to start after several attempts with several unknown warning lights illuminated. Additionally, on several occasions while driving at various speeds, the vehicle stalled without warning. The vehicle was taken to columbus chrysler Dodge jeep ram (2806 23rd st, columbus, ne 68601) where the vehicle was diagnosed with a defective engine switch. The manufacturer was notified of the failure. The vehicle was repaired. The failure mileage was 122,000. *bf*jb
NHTSA complaint #11327770
Oct 8, 2019power train
Tl* the contact owns a 2010 RAM 1500. While driving 65 MPH, the rear differential seized and independently slowed the vehicle down. The contact was able to get the vehicle off the road safely. Upon inspecting the vehicle, the contact noticed rear differential fluid on the ground and on the undercarriage of the vehicle. The vehicle was towed to the contact's residence. The… Read more
Tl* the contact owns a 2010 RAM 1500. While driving 65 MPH, the rear differential seized and independently slowed the vehicle down. The contact was able to get the vehicle off the road safely. Upon inspecting the vehicle, the contact noticed rear differential fluid on the ground and on the undercarriage of the vehicle. The vehicle was towed to the contact's residence. The vehicle was not diagnosed or repaired. A local dealer was not contacted. The vehicle was included in NHTSA campaign number: 13v038000 (power train). The manufacturer was informed of the failure. The approximate failure mileage was 196,000.
NHTSA complaint #11266967
Aug 9, 2019power train
Tl* the contact owns a 2010 RAM 1500. While driving approximately 25 MPH, the driveshaft detached from the vehicle and caused the rear tire to stop spinning. The vehicle was towed to the contact's residence and was not able to be driven. The dealer was not contacted. The vehicle was not repaired. The manufacturer was notified of the failure. The contact mentioned that the… Read more
Tl* the contact owns a 2010 RAM 1500. While driving approximately 25 MPH, the driveshaft detached from the vehicle and caused the rear tire to stop spinning. The vehicle was towed to the contact's residence and was not able to be driven. The dealer was not contacted. The vehicle was not repaired. The manufacturer was notified of the failure. The contact mentioned that the vehicle was previously repaired per an unknown manufacturer recall for the same defect. The approximate failure mileage was 176,000.
NHTSA complaint #11242733
Jun 19, 2019power train
Tl* the contact owns a 2010 RAM 1500. After the contact replaced the brake rotors, he test drove the vehicle and a loud noise was heard. Also, there was a vibration from the rear of the vehicle. The contact drove the vehicle back to his residence and noticed that the driveshaft was detached. The vehicle was taken to don franklin somerset chrysler Dodge jeep ram nissan (located… Read more
Tl* the contact owns a 2010 RAM 1500. After the contact replaced the brake rotors, he test drove the vehicle and a loud noise was heard. Also, there was a vibration from the rear of the vehicle. The contact drove the vehicle back to his residence and noticed that the driveshaft was detached. The vehicle was taken to don franklin somerset chrysler Dodge jeep ram nissan (located at 1147 south highway 27, summerset, ky 42501, (606) 678-8178) where it was diagnosed that all the gears and bearings needed to be replaced. The contact stated the failure recurred twice. The manufacturer was notified of the failure and advised the contact to take the vehicle to a dealer. No further assistance was offered. The approximate failure mileage was 101,300.
NHTSA complaint #11221235
Apr 7, 2019power train
After taking the truck through an automated car wash the transfer case shift motor engaged putting the transfer case in 4 low. This happened in a parking lot at low speed. If this malfunction happened on the highway it would likely have caused loss of control.
NHTSA complaint #11194487
Apr 2, 2019steering, power trainCrash1 injured
2010 Dodge RAM 1500 w/ gear shifter located on steering column was parked in a driveway when the gear shifter popped out of gear and began to roll. As a result, owner of vehicle suffered left ankle and thoracic fractures requiring hospitalization. Vehicle came to rest after crashing into a residential property.
NHTSA complaint #11197410
Mar 26, 2019power train
When I started the truck monday morning and put it in drive, it went straight into fourth gear. I thought I had accidentally put it in manual mode, so I turned it off and restarted it. In the drive position it would only operate in fourth gear. After a little research I discovered its called limp mode and it seems like the culprit is the transmission shift solenoid, sometimes… Read more
When I started the truck monday morning and put it in drive, it went straight into fourth gear. I thought I had accidentally put it in manual mode, so I turned it off and restarted it. In the drive position it would only operate in fourth gear. After a little research I discovered its called limp mode and it seems like the culprit is the transmission shift solenoid, sometimes called the range sensor, part number 68353383ab. I had taken it to a transmission shop and they told me that?s what the culprit was, but if I was going to replace it I might as well rebuild the transmission...$2800. Not being able to afford this, (nor did I think it was needed), I called advanced auto who ordered a solenoid pack for me, but it was the wrong one, (4800171aa). That?s when I called chrysler jeep Dodge off 295 in jacksonville florida. [xxx] give me the correct part number, let me know that it was a special order, and that they were only allowed to order five a week and it would take 5 to 7 days to come in. I said that seemed odd and asked if there was an issue. He said let me look, and that?s when he told me that they were fixing 640 of these a week nationwide, but there was no recall. How is that so? I was lucky in that my issue happened in/on my own driveway/street where I could back up and figure out a plan. But I have read where this is happening to people as they are out and about with no warning. Dangerous or not, over 33,000 repairs in a years time seems to be at recall level. The p
NHTSA complaint #11191749
Mar 24, 2019power train
Driving 25 MPH. Rear differential locked up. Drive line separated from the pinion gear. Violently thrown into the steering column. The rear differential was beyond repair. A replacement diffenential had to be replaced. Expensive repair. Chrysler refused to reimburse for the repair. Said it was my fault for not knowing about the existing recall notice. I was never notified of any such recall until after the incident.
NHTSA complaint #11191231
Jan 18, 2019power train
Broken manifold bolts causing ticking noise.
NHTSA complaint #11170810
Jan 17, 2019power train
Tl* the contact owns a 2010 RAM 1500. The contact stated that the part was not available within a reasonable time frame concerning NHTSA campaign number: 17v821000 (power train). Chrysler Dodge jeep ram at sheridan motor (1812 coffeen ave, sheridan, wy 82801, (307) 763-5884) indicated that they were only receiving one part per week. The manufacturer was contacted. The contact… Read more
Tl* the contact owns a 2010 RAM 1500. The contact stated that the part was not available within a reasonable time frame concerning NHTSA campaign number: 17v821000 (power train). Chrysler Dodge jeep ram at sheridan motor (1812 coffeen ave, sheridan, wy 82801, (307) 763-5884) indicated that they were only receiving one part per week. The manufacturer was contacted. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11170644
Dec 17, 2018power train
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign numbers: 12v474000 (power train) and 17v821000 (power train). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Tri-lakes motors (180 state hwy f, branson, mo 65616, (417) 334-7543) was contacted and confirmed that the parts were not… Read more
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign numbers: 12v474000 (power train) and 17v821000 (power train). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Tri-lakes motors (180 state hwy f, branson, mo 65616, (417) 334-7543) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was notified. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11161940
Dec 12, 2018power train
Tl* the contact owns a 2010 RAM 1500. The contact stated that the rear differential failed. While driving 35 MPH, the contact felt a strong shake and a loud noise coming from the rear of the vehicle. The contact was able to coast the vehicle onto a safe area and discovered that the rear differential separated from the vehicle. The contact was able to drive the vehicle to a… Read more
Tl* the contact owns a 2010 RAM 1500. The contact stated that the rear differential failed. While driving 35 MPH, the contact felt a strong shake and a loud noise coming from the rear of the vehicle. The contact was able to coast the vehicle onto a safe area and discovered that the rear differential separated from the vehicle. The contact was able to drive the vehicle to a mechanic who diagnosed that there were metal shavings found in the rear differential. The contact also stated that the computer head unit that controlled the heating, radio, and defroster failed. As a result, the defroster did not operate and the heat only blew onto the floorboard. The contact took the vehicle to an unknown chrysler dealer for the computer head unit. The dealer inspected the vehicle and advised that the computer head unit needed to be replaced. The manufacturer was contacted. The manufacturer advised that there was a technical service bulletin for the rear differential failure and a recall was not issued for the failure. The vehicle was not repaired. The failure mileage was 109,000.
NHTSA complaint #11160911
Nov 21, 2018power train
Tl* the contact owns a 2010 RAM 1500. The contact stated that the recall notice for NHTSA campaign number: 17v821000 (power train) was received in january of 2018. After contacting the local dealer (chyrsler of winona, 121 huff st, winona, mn), the contact was informed that the parts needed to repair the defect were not available. The manufacturer was notified. The contact… Read more
Tl* the contact owns a 2010 RAM 1500. The contact stated that the recall notice for NHTSA campaign number: 17v821000 (power train) was received in january of 2018. After contacting the local dealer (chyrsler of winona, 121 huff st, winona, mn), the contact was informed that the parts needed to repair the defect were not available. The manufacturer was notified. The contact had not experienced a failure. Parts distribution disconnect. *tt*jb
NHTSA complaint #11153122
Nov 21, 2018power train
Tl* the contact owns a 2010 RAM 1500. While driving 25 MPH, the sound of something vibrating was heard coming from the vehicle. The contact mentioned that the rear wheels seized and the driveshaft fractured. The vehicle was taken to ron carter chrysler jeep Dodge of league city (3535 gulf fwy, dickinson, tx 77539, (281) 206-0656) and the contact was informed that the vehicle… Read more
Tl* the contact owns a 2010 RAM 1500. While driving 25 MPH, the sound of something vibrating was heard coming from the vehicle. The contact mentioned that the rear wheels seized and the driveshaft fractured. The vehicle was taken to ron carter chrysler jeep Dodge of league city (3535 gulf fwy, dickinson, tx 77539, (281) 206-0656) and the contact was informed that the vehicle was diagnosed for the same failure in 2005. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was 132,000.
NHTSA complaint #11153099
Nov 2, 2018power train
A pinion nut in the drivetrain failed during normal use while driving down a highway at 65 MPH, the main driveshaft separated from the truck and sheared half of the transfer case off. The driveshaft also destroyed the rear differential and damaged a large are of the under carriage. This but was under recall and an accredited dealership made the initial repair by replacing the… Read more
A pinion nut in the drivetrain failed during normal use while driving down a highway at 65 MPH, the main driveshaft separated from the truck and sheared half of the transfer case off. The driveshaft also destroyed the rear differential and damaged a large are of the under carriage. This but was under recall and an accredited dealership made the initial repair by replacing the transfer case and driveshaft. The rear differential was repaired. After the repairs were made the trucks drivetrain would not operate correctly and would try to shift itself into 4wd intermittently without the transfer case selector being moved. The dealership was unable to troubleshoot the problem for a number of weeks but finally discovered the transfer case motor was broken and that the initial repair should have included this part as it was obviously damaged in the incident but could not make the repair because it wasn't listed on the initial repair. Fca refused to replace the part and would not accept an appeal to have the case reviewed to include the new information as the area manager responsible for our claim closed it without allowing the new troubleshooting results to be considered.
NHTSA complaint #11144970
Oct 30, 2018power train
Driving about 35 MPH and a whirring started in the rear end. Only happened when I was coasting, not when gas was applied or brakes. After about 15 minutes of driving and several stops the drive shaft fell off. I was coasting down hill on a two lane road as the noise got very loud. First there was a clunk and obviously something was dragging underneath, which I thought was… Read more
Driving about 35 MPH and a whirring started in the rear end. Only happened when I was coasting, not when gas was applied or brakes. After about 15 minutes of driving and several stops the drive shaft fell off. I was coasting down hill on a two lane road as the noise got very loud. First there was a clunk and obviously something was dragging underneath, which I thought was the muffler. There was no where to stop on the road so continued to coast. Less than 5 seconds later another clunk and then it was quiet, piece had fallen off. I was able to pull to side of road but vehicle was inoperable. Estimate from dealership is to replace drive shaft and whole rear end assembly, $6200. Only explanation given was that a u-joint broke and fell off. Drive shaft falling out damaged whole rear end assembly.
NHTSA complaint #11144131
Sep 21, 2018power train
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign number: 17v821000 (power train); however, the parts to do the recall repair were not available. The dealer (sterling heights Dodge chrysler jeep ram, 40111 van dyke ave, sterling heights, mi 48313, 586-939-3900) was contacted and confirmed that parts were not available for the recall… Read more
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign number: 17v821000 (power train); however, the parts to do the recall repair were not available. The dealer (sterling heights Dodge chrysler jeep ram, 40111 van dyke ave, sterling heights, mi 48313, 586-939-3900) was contacted and confirmed that parts were not available for the recall remedy. The manufacturer was not contacted. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11130597
Sep 6, 2018steering, power train, electrical system
Electrical issues have been prevalent since the date of purchase in 2013. Must be a short in the entire truck somewhere. My lights on the passenger mirror blink all the time while running and or opening the door. Hubs/cv axles have had to replace both driver and passenger side 3 times each now. This vehicle in not used and abused. I take care of it with regular… Read more
Electrical issues have been prevalent since the date of purchase in 2013. Must be a short in the entire truck somewhere. My lights on the passenger mirror blink all the time while running and or opening the door. Hubs/cv axles have had to replace both driver and passenger side 3 times each now. This vehicle in not used and abused. I take care of it with regular maintenance. I have heard from others who own same year model and have seen online on forums others have had these issues also. This causes the cv, hubs, and rotors/brakes to be replaced.
NHTSA complaint #11127879
Aug 28, 2018power train
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign number: 17v821000 (power train). The contact called chuck patterson toyota at 530-895-1771 (located at 200 east ave, chico, ca 95926) and was informed that the parts were not available. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become… Read more
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign number: 17v821000 (power train). The contact called chuck patterson toyota at 530-895-1771 (located at 200 east ave, chico, ca 95926) and was informed that the parts were not available. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11123007
Aug 20, 2018power train, fuel/propulsion system
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v160000 (fuel system, gasoline). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. Eddy's chrysler Dodge jeep ram (11028 w kellogg dr, wichita, ks 67209, (316) 773-2002) was contacted and confirmed… Read more
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v160000 (fuel system, gasoline). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. Eddy's chrysler Dodge jeep ram (11028 w kellogg dr, wichita, ks 67209, (316) 773-2002) was contacted and confirmed that the parts were not available for the recall remedies. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11121146
Aug 20, 2018power train, fuel/propulsion system
Tl* the contact owns a 2010 RAM 1500. The contact stated that when the shifter was engaged, it intermittently jammed. The failure occurred without warning. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v160000 (fuel system, gasoline). The parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a… Read more
Tl* the contact owns a 2010 RAM 1500. The contact stated that when the shifter was engaged, it intermittently jammed. The failure occurred without warning. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v160000 (fuel system, gasoline). The parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. Larkmark south Dodge chrysler jeep ram (7820 e 171st st, belton, mo) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The failure mileage was unknown. Parts distribution disconnect. **tr updated 10/31/18*jb
NHTSA complaint #11121116
Jul 31, 2018power train
While in reverse the truck makes a loud popping sound and it feels like the brake is grabbing the rotor. The caliper was changed and the issue persists. I was told by the local Dodge dealership it could be the drive line rear-end pinion nut backing off the bolt that this is a common issue, either way there are numerous complaints and this should be recalled before someone is… Read more
While in reverse the truck makes a loud popping sound and it feels like the brake is grabbing the rotor. The caliper was changed and the issue persists. I was told by the local Dodge dealership it could be the drive line rear-end pinion nut backing off the bolt that this is a common issue, either way there are numerous complaints and this should be recalled before someone is seriously injured or killed. This only occurs when backing up slowly with the brake pedal pressed.
NHTSA complaint #11114986
Jul 16, 2018power train, engine
Tl* the contact owns a 2010 RAM 1500. The contact stated that the vehicle lost power several times without warning and stalled. The vehicle was towed to the dealer (twin rivers chrysler-jeep-Dodge inc, 529 w court st, beatrice, ne 68310, (402) 228-3311) for diagnostic testing and repairs. The results of the diagnostic were not available. The manufacturer was not made aware of… Read more
Tl* the contact owns a 2010 RAM 1500. The contact stated that the vehicle lost power several times without warning and stalled. The vehicle was towed to the dealer (twin rivers chrysler-jeep-Dodge inc, 529 w court st, beatrice, ne 68310, (402) 228-3311) for diagnostic testing and repairs. The results of the diagnostic were not available. The manufacturer was not made aware of the failure. The contact was not aware that the vehicle was included in NHTSA campaign number: 17v821000 (power train). The failure mileage was not available.
NHTSA complaint #11111516
Jul 2, 2018fuel system, gasoline, power train
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v160000 (fuel system, gasoline). The contact called baxter chrysler Dodge jeep ram lincoln at 402-817-7449 (located at 6601 telluride dr. A, lincoln, ne 68521) and was informed that the parts were not available. The manufacturer was made aware of the… Read more
Tl* the contact owns a 2010 RAM 1500. The contact received notification of NHTSA campaign numbers: 17v821000 (power train) and 18v160000 (fuel system, gasoline). The contact called baxter chrysler Dodge jeep ram lincoln at 402-817-7449 (located at 6601 telluride dr. A, lincoln, ne 68521) and was informed that the parts were not available. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA complaint #11105172