Nov 24, 2022suspension, electrical system, structure
The entire underneath of my car is rusted out. I was driving to work one day when someone pulled out in front of me and I had to hit the brakes. That resulted in the subframe and front drivers axel to break as I’m driving! The sunroof leaks when it rains and half the time the electricity doesn’t work on the sunroof button. My doors have completely stopped auto locking and my… Read more
The entire underneath of my car is rusted out. I was driving to work one day when someone pulled out in front of me and I had to hit the brakes. That resulted in the subframe and front drivers axel to break as I’m driving! The sunroof leaks when it rains and half the time the electricity doesn’t work on the sunroof button. My doors have completely stopped auto locking and my hazards will randomly start flashing without pushing the button. Steering is absolutely terrible, it feels like you’re skidding on ice or hydroplaning the entire drive.
NHTSA complaint #11494825
Apr 15, 2022structure, unknown or other
Subframe rusted front and rear was driving tire axel/rod broke entire underneath rusted rotted
NHTSA complaint #11460835
Sep 23, 2021structure
The contact owns a 2008 Dodge Caliber. The contact stated while taking the vehicle into a local state inspection, he was notified that the vehicle did not pass inspection due to the k-frame of the undercarriage was fractured due to corrosion and rust. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 159,000.
NHTSA complaint #11434129
Apr 7, 2021suspension, structure
2008 Dodge Caliber sub frame/k-frame front end crossmember completely rusted thru causing the driver side lower control arm to rip free from frame (seperating part of frame, with lower control arm) from rest of frame. This left driver with no control of affected wheel which turning it 90 degrees out from normal operating position. Left operator with no ability to steer while… Read more
2008 Dodge Caliber sub frame/k-frame front end crossmember completely rusted thru causing the driver side lower control arm to rip free from frame (seperating part of frame, with lower control arm) from rest of frame. This left driver with no control of affected wheel which turning it 90 degrees out from normal operating position. Left operator with no ability to steer while driving on main primary (35 MPH speed limit) two lane road. Car slid to halt in middle of road. Car needed to be towed. Dodge/chrysler apparently knew of this problem and never notified owner. Please see attached notice. Front and rear crossmember corrosion (x69 warranty extension) - 2008-2012 Dodge Caliber & jeep compass/patriot oemdtc july 17, 2017 15 comments NHTSA id number: 10140027 manufacturer communication number: 23-007-17 rev. B summary front and rear crossmember corrosion (x69 warranty extension) the driver of this car could have been killed or seriously hurt. It is unfathomable that Dodge chrysler was allowed to get away with not notifying potential crash victims
NHTSA complaint #11406812
Jun 30, 2020suspension, structure
Recently purchased a 2008 Dodge Caliber(ohio). On initial drive returning with vehicle I noticed a vibration coming through steering wheel. Upon inspection, was informed the tie rod ends and control arms both could use replacement, but could have been caused by the more important bad front and rear crossmembers as well as front and rear crash bars, both have severe rust… Read more
Recently purchased a 2008 Dodge Caliber(ohio). On initial drive returning with vehicle I noticed a vibration coming through steering wheel. Upon inspection, was informed the tie rod ends and control arms both could use replacement, but could have been caused by the more important bad front and rear crossmembers as well as front and rear crash bars, both have severe rust development with metal deterioration which could impose a safety concern down the road. Was advise to look into replacement. Reached out to one of the local dealerships and was informed it was a bulletin, had an extended warranty, but am outside of 10 year period. Rust from crossmember is now in process of transferring to actual frame and coming through as holes in rockers now as well. Dealership offering no help after stating the enhanced safety concern. Hard to believe an 08 can deteriorate so fast. You would think with the complaints and t.s.b. As well as safety concerns, seeing still original parts that have been warrantied to replace but have not on this VIN, gets no help at all. *tr
NHTSA complaint #11331646
May 26, 2020suspension, structure, unknown or other
While my wife was driving, the front subframe crossmember rusted through, causing her to lose control of the car and she could not safely operate it without repair. I managed to get it to a firestone for them to look at and they referred me to a dealer and told me not to drive it anymore because it is unsafe. This is a problem that Dodge knew about, but failed to notify me… Read more
While my wife was driving, the front subframe crossmember rusted through, causing her to lose control of the car and she could not safely operate it without repair. I managed to get it to a firestone for them to look at and they referred me to a dealer and told me not to drive it anymore because it is unsafe. This is a problem that Dodge knew about, but failed to notify me about. I only found out about the problem from the dealership, who told me that the extended warranty that covers this problem had expired in 2018 and that I would be responsible for the cost of any repairs. I owned the car during that time and I did not know of this problem, so I could not act on getting it repaired. This never should have been an extended warranty, this should have been a recall because of the potential to kill people when the subframe rusts out. My wife was driving in a parking lot at the time at a relatively low speed, but had this happened on a highway it could have killed her and my son, as well as others on the road. Number: 23-007-17 rev. B group: body date: march 10, 2017 *tr
NHTSA complaint #11325979
Nov 15, 2019structure
Fiat chrysler america released 2 bulletins and an extended warranty for an inferior material causing severe rust and perforation of the front and rear crossmember on 2008-2012 Dodge Caliber and 2008-2012 jeep compass patriot. The crossmember is an important structural component of any vehicle. It supports the underside of the car and carries the weight of the engine and… Read more
Fiat chrysler america released 2 bulletins and an extended warranty for an inferior material causing severe rust and perforation of the front and rear crossmember on 2008-2012 Dodge Caliber and 2008-2012 jeep compass patriot. The crossmember is an important structural component of any vehicle. It supports the underside of the car and carries the weight of the engine and transmission. Fca customer service is currently refusing to replace these parts even though the bulletin acknowledges that the part is faulty. The severe rust on this part will cause my vehicle to no longer pass state inspection. I have owned my 2008 Dodge Caliber since february 2017. The first bulletin released by fca regarding knowledge of this faulty part was march 2017, one month after I purchased the car. A second bulletin regarding the same issue was released july 2017. The extended warranty expired on august 2018. After the second bulletin was issued, there was a period of 13 months before the warranty expired and while I owned the car. I was not contacted or made aware by fca in any way that the vehicle I was driving had a known issue and that I could have it addressed within extended warranty. It was not until october 2019 that I was having work done on my car and the mechanic brought it to my attention because the rust is so bad it will not pass the next state inspection. Photographs are included. I encourage the NHTSA to recall this part as a safety issue. The rust weakens the metal and if t
NHTSA complaint #11280345
Oct 7, 2019steering, structure
Tl* the contact owns a 2008 Dodge Caliber. While driving 20 MPH, the steering wheel became difficult to move and the contact heard an abnormal noise. The contact stated that the check engine warning indicator illuminated. The vehicle was taken to a muffler shop where it was diagnosed that the cross member bar needed to be replaced. The vehicle was not repaired. The… Read more
Tl* the contact owns a 2008 Dodge Caliber. While driving 20 MPH, the steering wheel became difficult to move and the contact heard an abnormal noise. The contact stated that the check engine warning indicator illuminated. The vehicle was taken to a muffler shop where it was diagnosed that the cross member bar needed to be replaced. The vehicle was not repaired. The manufacturer and dealer were not notified. The failure mileage was 56,500. *dt the consumer stated the vehicle was repaired the same day at the tune of $1,100 at owners expense for a recalled part. *tr *dt the consumer provided photos of the defect. *tr *tr
NHTSA complaint #11266869
Aug 14, 2019suspension, electrical system, structure
One headlight doesn't,work sub frame completely rusted, doors lock at different speeds shock and struts are horrible squeaks and makes really bad sounding noises at any speed even backing out
NHTSA complaint #11244034
Jul 19, 2019structure
Tl* the contact owns a 2008 Dodge Caliber. While driving 25 MPH, the contact heard an abnormal noise coming from the rear and front wheels. There were no warning indicators illuminated. The vehicle was taken to ridenour auto group (500 w broadway st, new lexington, oh 43764, (740) 342-5146) where it was diagnosed that the rear and front subframe was corroded and needed to be… Read more
Tl* the contact owns a 2008 Dodge Caliber. While driving 25 MPH, the contact heard an abnormal noise coming from the rear and front wheels. There were no warning indicators illuminated. The vehicle was taken to ridenour auto group (500 w broadway st, new lexington, oh 43764, (740) 342-5146) where it was diagnosed that the rear and front subframe was corroded and needed to be replaced. The oil was changed, but the subframe was not repaired. The failure recurred. The manufacturer was made aware of the failure and stated that the VIN was not included in a recall. The failure mileage was approximately 30,000.
NHTSA complaint #11233335
Jul 6, 2019steering, structure, wheels
I was driving down the road every time I shifted gears the front end would just go like wobble wobble so I slow down from 45 to about 10 miles an hour if that I made it home with zagg got underneath there and the sub frame is literally busted the way it sits it looks like it does not have a motor in it anymore if I want to know what to do I would've wrecked if I do not get an… Read more
I was driving down the road every time I shifted gears the front end would just go like wobble wobble so I slow down from 45 to about 10 miles an hour if that I made it home with zagg got underneath there and the sub frame is literally busted the way it sits it looks like it does not have a motor in it anymore if I want to know what to do I would've wrecked if I do not get an answer soon I am going to channel 13 news I have pictures of what it looks like and I'm going to the better business bureau it's a 2008 there is no way that frame should've busted like it did no way I was on city roads
NHTSA complaint #11229800
Jul 1, 2019suspension, structure
Tl* the contact owns a 2008 Dodge Caliber. While the vehicle was at an intersection, the vehicle shook violently when the accelerator pedal was depressed. There were no warning indicators illuminated. The contact managed to steer the vehicle home while it shook. The contact looked under the vehicle and noticed that the rear subframe was fractured. The dealer was not contacted.… Read more
Tl* the contact owns a 2008 Dodge Caliber. While the vehicle was at an intersection, the vehicle shook violently when the accelerator pedal was depressed. There were no warning indicators illuminated. The contact managed to steer the vehicle home while it shook. The contact looked under the vehicle and noticed that the rear subframe was fractured. The dealer was not contacted. The manufacturer was made aware of the failure and informed the contact to file a complaint with NHTSA. The vehicle was not repaired. The failure mileage was approximately 162,321. *bf consumer stated front subframe rusted and corrosion, VIN is xxxx. 'parts of this document have been redacted to protect personally identifiable information pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).'*jb
NHTSA complaint #11228796
Jun 28, 2019suspension, power train, structure, service brakes
Tl* the contact owns a 2008 Dodge Caliber. While driving, the contact heard a loud noise. The contact later discovered that the subframe was rusted through and caused the front driver's side axle to fracture. Also, the top of the driver's side wheel was tilted inward. The vehicle was towed to an independent mechanic and the axle, subframe, one of the brakes, and the… Read more
Tl* the contact owns a 2008 Dodge Caliber. While driving, the contact heard a loud noise. The contact later discovered that the subframe was rusted through and caused the front driver's side axle to fracture. Also, the top of the driver's side wheel was tilted inward. The vehicle was towed to an independent mechanic and the axle, subframe, one of the brakes, and the transmission fluid line were replaced. The dealer was not contacted. The contact called the manufacturer and was transferred to NHTSA. The failure mileage was 112,850.
NHTSA complaint #11223181
Jun 23, 2019steering, structure, engine
I purchased this vehicle knowing of rust but when I climbed under it I seen the subframe is almost rusted all the way through this is a major issue I've heard of a few other Caliber owners who's whole drivetrain fell out of engine bay due to this, this could be a dangerous problem if someone is driving at highway speeds Dodge needs to take action and recall this part and put a… Read more
I purchased this vehicle knowing of rust but when I climbed under it I seen the subframe is almost rusted all the way through this is a major issue I've heard of a few other Caliber owners who's whole drivetrain fell out of engine bay due to this, this could be a dangerous problem if someone is driving at highway speeds Dodge needs to take action and recall this part and put a better component on the vehicles they produce
NHTSA complaint #11222009
Jun 8, 2019suspension, structure, unknown or other
Let me start by saying that I love driving my 2008 Dodge Caliber and wish that it was worth repairing all of the issues that I am researching are common problems among fellow owners of this year, make and model of vehicle. As a person who pays close attention to my vehicle, repair costs have been adding up over the past couple of years. Starting with a complete repair related… Read more
Let me start by saying that I love driving my 2008 Dodge Caliber and wish that it was worth repairing all of the issues that I am researching are common problems among fellow owners of this year, make and model of vehicle. As a person who pays close attention to my vehicle, repair costs have been adding up over the past couple of years. Starting with a complete repair related to the suspension including the control arms/ bushings, sway bar, ball joints, and tie rods, which has caused my 4 new tires to experience a shortened lifespan due to uneven wearing. Recently, I had my car in the shop to address a loud noise I was hearing while the vehicle was in motion. The mechanic diagnosed a long list of issues, including rusting/corrosion to the engine cradle and further problems with the suspension that in their professional opinion determined the vehicle unsafe to operate. At this point, the mechanic informed me that there had been recalls and an extended warranty implemented to address the rusting/corrosion of the sub frame, as I was unaware and did not receive any notices for any of the listed recalls. Today, I find myself researching the list of problems that the mechanic indicated with the suspension and rotting engine cradle and will unfortunately not be worth putting thousands of dollars into to make it safe, an issue that should be honoured by the manufacturer. I would like to take the proper steps to address this extreme safety concern that has been an obvious issue for ma
NHTSA complaint #11218619
Apr 26, 2019structure
I went to my local Dodge dealer for oil change and was informed that front sub frame is rotting out. Was told extended warranty that was good for 10 years expired 2-18. I have read online numerous Caliber owners with this problem, some so bad they can't be fixed. What good is an extended warranty that is only good for the first ten years and I bought this car in 2012 from a… Read more
I went to my local Dodge dealer for oil change and was informed that front sub frame is rotting out. Was told extended warranty that was good for 10 years expired 2-18. I have read online numerous Caliber owners with this problem, some so bad they can't be fixed. What good is an extended warranty that is only good for the first ten years and I bought this car in 2012 from a Dodge dealer and was never informed of extended warranty for this issue or that there was even an issue with this. This is a major safety concern as what chances would a person have of surviving at a speed of 70 MPH and the frame breaks? Or what innocent people could be killed because of it. With this many persons having this issue and such a serious safety problem there should be a recall. My car only has 126,500 miles on it. If Dodge does not want to do a recall then I feel they don't give a [xxx] about their customers and will not buy another Dodge or chrysler again. Please consider persuing a recall for this vehicle issue as it is serious!! Parts of this document have been redacted to protect personally identifiable information pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
NHTSA complaint #11203972
Mar 11, 2019structure
Tl* the contact owns a 2008 Dodge Caliber. The contact stated that the vehicle made unusual noises while driving at any speed. The contact noticed that the frame, including the engine cradle, was completely rusted. The dealer was not contacted. The manufacturer was made aware of the failure and referred the contact to NHTSA. The vehicle was not diagnosed or repaired. The failure mileage was approximately 151,000.
NHTSA complaint #11185885
Feb 15, 2019structure
Frame on vehicle is rusted through, other similiar vehicles were issued recalls and this car was not
NHTSA complaint #11180307
Jan 28, 2019structure
Tl* the contact owns a 2008 Dodge Caliber. While the contact's son was driving 30 MPH, the front driver's side wheel detached from the vehicle. The vehicle was taken to an independent mechanic who diagnosed that the subframe and the crossmember were rusted. The vehicle was not repaired. The manufacturer was notified of the failure. The dealer was not contacted. The failure mileage was approximately 113,000.
NHTSA complaint #11172647
Nov 26, 2018suspension, structure
I purchased the 2008 Dodge Caliber 2 weeks ago nov 15th 2008 and inspected before purchase. Drove car 1 week and crossmember support beam broke due to poor part from mopar, Dodge. They had a 120month unlimited warrenty on part, knowing it was a bad part. I have tried all areas of getting bad part replaced to no avail. They say warrenty "expired" on defective part installed on… Read more
I purchased the 2008 Dodge Caliber 2 weeks ago nov 15th 2008 and inspected before purchase. Drove car 1 week and crossmember support beam broke due to poor part from mopar, Dodge. They had a 120month unlimited warrenty on part, knowing it was a bad part. I have tried all areas of getting bad part replaced to no avail. They say warrenty "expired" on defective part installed on car. I need car repaired as it is a danger!! Any help is greatly appreciated! I was turning into my driveway at normal speeds when crossmember support beam broke at drivers wheel area.
NHTSA complaint #11154002
Oct 23, 2018suspension, structure
Tl* the contact owns a 2008 Dodge Caliber. While driving various speeds, a dragging noise was heard coming from under the front driver's side of the vehicle. The vehicle was taken to the local dealer (wilmington auto, 1780 rombach ave, wilmington, oh) where it was diagnosed that the front driver's side control arm was fractured due to severe rusting and corrosion of the… Read more
Tl* the contact owns a 2008 Dodge Caliber. While driving various speeds, a dragging noise was heard coming from under the front driver's side of the vehicle. The vehicle was taken to the local dealer (wilmington auto, 1780 rombach ave, wilmington, oh) where it was diagnosed that the front driver's side control arm was fractured due to severe rusting and corrosion of the subframe. The vehicle was repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 130,000.
NHTSA complaint #11142140
Oct 18, 2018structure
Tl* the contact owns a 2008 Dodge Caliber. While driving approximately 25 MPH, the steering wheel shook without warning. The contact stated that the failure started approximately six months ago and was becoming worse. The vehicle was taken to spitzer Dodge jeep ram (13001 brook park road, brook park, oh 44142) where it was diagnosed that the subframe was severely corroded and… Read more
Tl* the contact owns a 2008 Dodge Caliber. While driving approximately 25 MPH, the steering wheel shook without warning. The contact stated that the failure started approximately six months ago and was becoming worse. The vehicle was taken to spitzer Dodge jeep ram (13001 brook park road, brook park, oh 44142) where it was diagnosed that the subframe was severely corroded and needed replacement. The manufacturer was notified of the failure. The vehicle was not repaired. The approximate failure mileage was 115,860.
NHTSA complaint #11141315
Oct 16, 2018suspension, structure
Tl* the contact owns a 2008 Dodge Caliber. While driving various speeds, a clunking noise was present coming from the rear of the vehicle. The vehicle was taken to the local independent mechanic who diagnosed that the rear cross member had separated due to severe rusting. The vehicle was not repaired. The manufacturer and local dealer (haley of farmville, 1906 s. Main st.,… Read more
Tl* the contact owns a 2008 Dodge Caliber. While driving various speeds, a clunking noise was present coming from the rear of the vehicle. The vehicle was taken to the local independent mechanic who diagnosed that the rear cross member had separated due to severe rusting. The vehicle was not repaired. The manufacturer and local dealer (haley of farmville, 1906 s. Main st., farmville, va) were notified of the failure, but no assistance was offered. The failure mileage was 60,000. *tt *jb
NHTSA complaint #11140652
Sep 25, 2018structure
My 2008 Dodge Caliber is rusting all over due to chrysler not prepping/coating the vehicle properly. So far I have had the crossmember that holds the engine on replaced due to rust, the oil pan and the power steering line rusted. I have rust all over the body of the vehicle from inside wheel well, bottom of doors, transmission pan, above the windshield, multiple places on the… Read more
My 2008 Dodge Caliber is rusting all over due to chrysler not prepping/coating the vehicle properly. So far I have had the crossmember that holds the engine on replaced due to rust, the oil pan and the power steering line rusted. I have rust all over the body of the vehicle from inside wheel well, bottom of doors, transmission pan, above the windshield, multiple places on the hood, bottom of the hatch, rocker panels, hinges etc.... Way too many places for a vehicle that age. I have seen other 2008's with no rust at all. I have multiple pictures but it will only allow 5.
NHTSA complaint #11131555
Sep 1, 2018suspension, structure
The problem deal with the front crossmember subframe. This part is total junk. It is completed rusted out. It was just a miracle it did not cause an accident prior to our finding it needed replaced. After checking online and finding the 2007 Caliber's were handled under a "recall" but nothing has been done on subsequent years. After just leaving home the right front wheel… Read more
The problem deal with the front crossmember subframe. This part is total junk. It is completed rusted out. It was just a miracle it did not cause an accident prior to our finding it needed replaced. After checking online and finding the 2007 Caliber's were handled under a "recall" but nothing has been done on subsequent years. After just leaving home the right front wheel pulled badly to the right, while making screaking noises. The car was limped back into the drive and the problem found. I believe this is a very poorly made part, probably with inferior steel. I have attached two (2) pictures of the old subframe. The car is registered to my daughter [xxx] , I am her father [xxx]. I contacted a local dealer and expressed my concerns and they informed me to contact Dodge/chrysler which I did. They informed there was no assistance for this issue. They did take my complaint. I believe this to be a serious safely issue with any vehicle that has this type of crossmember subframe. Please contact me if you need any other information. [xxx]or by cell phone [xxx]. I would appreciated any type of reply. Sincerely [xxx]. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr
NHTSA complaint #11123912
Aug 5, 2018suspension, structure
I took car in to have ball joints replacedplus the steering and struts looked at. Mechanic showed that the frame is totally rusted through. No other work can be done on the car with this huge issue.
NHTSA complaint #11115837
Jul 24, 2018suspension, structure
Vehicle arrived at our shop for a standard oil change and on inspection we discovered that the sub frame had rotted and the vehicle is unsafe to drive. We contacted the dealer for the customer and found that the extended warranty had expired. This is a road hazard and should have no expiration date. Photo is available if there is an investigation. *tr
NHTSA complaint #11113279
Jul 18, 2018structure
Air condenser drips outlet directly onto engine cradle which causes the cradle to rust know problem to fca and it should be known to NHTSA as separation of engine cradle causes an unsafe vehicle
NHTSA complaint #11112169
Jul 10, 2018electrical system, structure
Coming home from a trip and stopped to put gas in and it was night time and the dash lights would not come on. It happened 3 times now. I do not like driving home with a flashlight. Also the other problem we have is we had. Our oil changed and we're told that the front subframe is rusting out and the oil pan will need to be replaced soon
NHTSA complaint #11110581
Jul 2, 2018structure
Taking the car in for alignment, the tech notice the sub frame had a large hole from rust.. Taking the car to the Dodge dealer. The service manger stated they could not do anything, I was told "s*** out of luck". He said I was over the mileage, and past the ten years. The car was in for its life time powertrain inspection a month and a half before the ten years and replacing… Read more
Taking the car in for alignment, the tech notice the sub frame had a large hole from rust.. Taking the car to the Dodge dealer. The service manger stated they could not do anything, I was told "s*** out of luck". He said I was over the mileage, and past the ten years. The car was in for its life time powertrain inspection a month and a half before the ten years and replacing the alternator. They (Dodge replace my sons subframe with with 140,000 miles. Have the copy from the same dealer, a copy from a man in michagan whose frame broke get on I-90 and the towing service said they get one to two pickup per week on frames braking. Also I have not recvied any letter Dodge about the problem.
NHTSA complaint #11105061
Jun 12, 2018structure
Tl* the contact owns a 2008 Dodge Caliber. While inspecting underneath the vehicle, the contact noticed that the cross member was rusted and contained holes. There were no warning indicators illuminated. The vehicle was not taken to a dealer or independent mechanic for diagnostic testing or repair. The manufacturer was not aware of the failure. The failure mileage was 107,000.
NHTSA complaint #11101426
Apr 25, 2018suspension, structure
Rusted sub-frame & oil pan
NHTSA complaint #11090104
Mar 28, 2018structure
Took my car in for an alignment and was notified about my k frame rotting. The mechanic told me he worked on a jeep compass with same problems and chrysler had a extended warranty covering it. Called Dodge they told me to bring it into a dealership so they can verify and when they did verify it they told chrysler about the issue. Chrysler called and told me they will not fix… Read more
Took my car in for an alignment and was notified about my k frame rotting. The mechanic told me he worked on a jeep compass with same problems and chrysler had a extended warranty covering it. Called Dodge they told me to bring it into a dealership so they can verify and when they did verify it they told chrysler about the issue. Chrysler called and told me they will not fix my front k frame because I had recently put in after market parts in the rear of my car which caused my front k frame to rust and I've only had those parts installed a week before taking it to Dodge. So I told the customer service rep. There's no need to make excuses or lies if they don't want to fix and that I've talked to my main mechanic, the alignment mechanic, and the Dodge service rep., all 3 said it needs to be replace and is dangerous to continue driving as the front k frame holds mostly everything under the hood. Sad as it is chrysler gave no care.
NHTSA complaint #11081873
Feb 21, 2018structure
Tl* the contact owns a 2008 Dodge Caliber. The contact stated that the frame of the vehicle was rusted out. The vehicle was taken to an independent mechanic where it was diagnosed that the vehicle was not repairable. A local dealer was not contacted. The manufacturer was made aware of the failure and advised the contact that the failure was due to normal wear and tear. The failure mileage and VIN were unknown.
NHTSA complaint #11074028
Jan 9, 2018structure
Door hinge issue. Initially the door seemed just stuck difficult to close sprayed wd-40 when needed. The other day the entire door shifted and would not close properly. The spring and hinge dislocated shifting door where it catches bends the front fender. When looking online I see that this is common
NHTSA complaint #11061353
Oct 17, 2017suspension, structure, unknown or other
A frame rusted out and everything else under the car has no rust and now it's a saggy issue
NHTSA complaint #11034030
Feb 8, 2017structure
Engine cradle is rotted clear out an actually broke! This is very unsafe.im sure the back end is the same way! Dodge will not pay to have it fixed.they have an extended warranty on the 2007 calibers.mine was made in feb. Of 2008, it has the exact same parts!! Been trying to get Dodge to own up an fix this problem.needless to say I won't ever buy another Dodge product.also I… Read more
Engine cradle is rotted clear out an actually broke! This is very unsafe.im sure the back end is the same way! Dodge will not pay to have it fixed.they have an extended warranty on the 2007 calibers.mine was made in feb. Of 2008, it has the exact same parts!! Been trying to get Dodge to own up an fix this problem.needless to say I won't ever buy another Dodge product.also I was driving on the highway when the frame broke.
NHTSA complaint #10950394
Feb 7, 2017structure
Tl* the contact owns a 2008 Dodge Caliber. While driving various speeds, the vehicle shook violently without warning. The vehicle was taken to the dealer where it was diagnosed that the undercarriage was rusted. The vehicle was unable to be driven. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 97,000.
NHTSA complaint #10950098
Feb 1, 2017structure
Tl* the contact owns a 2008 Dodge Caliber. The contact stated that the sub frame was completely corroded and rusted. The vehicle was not taken to the dealer. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was 70, 000.
NHTSA complaint #10948799
Jan 23, 2017suspension, engine and engine cooling, structure
Engine cradle mounting and front suspension plates have failed or broken twice on this car online complaints seem very similar dealer seems to ignore this problem but will fix it for 2000.00 car pulls or veers unexpectedly while moving I cannot I feel safely drive anymore. *tr
NHTSA complaint #10947216