Oct 29, 2018service brakes
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the vehicle was put on a lift and it was discovered that the brake line was corroded, causing a leak. The vehicle was taken to an independent mechanic where it was diagnosed that the brake lines needed to be replaced. The contact called the ed bozarth Chevrolet dealer (877-721-4901, 3731 sw topeka… Read more
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the vehicle was put on a lift and it was discovered that the brake line was corroded, causing a leak. The vehicle was taken to an independent mechanic where it was diagnosed that the brake lines needed to be replaced. The contact called the ed bozarth Chevrolet dealer (877-721-4901, 3731 sw topeka blvd, topeka, ks 66609) and was told that there was no recall. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure mileage was 140,000. *tt consumer stated brake lines corroded and was leaking. Updated 12/18/18*jb
NHTSA complaint #11143762
Oct 1, 2018service brakes
I was slowing for a stop sign while leaving a parking lot when the steel rear brake line spontaneously split and dumped all line pressure. The brake pedal went straight to the floor, and I rolled right into traffic before I was able to pump the pedal enough times to stop the vehicle against a curb. Had I neared the stop sign 2 seconds earlier or later, I would have either been… Read more
I was slowing for a stop sign while leaving a parking lot when the steel rear brake line spontaneously split and dumped all line pressure. The brake pedal went straight to the floor, and I rolled right into traffic before I was able to pump the pedal enough times to stop the vehicle against a curb. Had I neared the stop sign 2 seconds earlier or later, I would have either been t-boned by a box truck, or t-boned a small sedan. I emphasize that the brake lines showed no warning signs beyond the typical surface rust that can be found on any vehicle that has been driven for more than a few winters in the "rust belt". However, those vehicles do not have brake lines spontaneously fail at the rate that these GM trucks do. This truck's primary purpose is towing a camping trailer for vacations with my young family, so this could have ended very differently. I urge you to take GM to task and force them to fix their mistake of cheaping out on brake line materials!
NHTSA complaint #11132674
Aug 23, 2018service brakes
I had a major brake failure the other day while driving. I had no brakes, but I was able to stop with the emergency brake. I had the truck towed to the mechanic and they reported that the brake failure was due to rusted brake lines.
NHTSA complaint #11121992
Jul 12, 2018service brakes
This issue occurred in july of 2016 while we were on vacation in florida. We began to lose braking ability until finally the vehicle became almost inoperable, only able to travel at about 20 MPH and still be able to stop without hitting anything. One of the steel brakes lines had blown a hole in it. We had a shop repair it and when they tested it, it blew another line. We… Read more
This issue occurred in july of 2016 while we were on vacation in florida. We began to lose braking ability until finally the vehicle became almost inoperable, only able to travel at about 20 MPH and still be able to stop without hitting anything. One of the steel brakes lines had blown a hole in it. We had a shop repair it and when they tested it, it blew another line. We ended up having all the lines replaced because of the level of corrosion.
NHTSA complaint #11110948
Aug 20, 2015service brakes
Complete break failure. Break pedal went to floor and almost killed my family. Noticed leaking break fluid coming out of rusted break line under vehicle.
NHTSA complaint #10750100
Jan 28, 2015service brakesCrash
I pulled into a parking lot and proceeded to park my suburban. I hit the brake pedal and the brakes did not work. They pulsate and gave out completely. No service lights or warning light came on previous to the incident. When the brakes didn't work I tried to pump them to get them to work but nothing worked and my suburban smashed into a bush and over the curb. I just had my… Read more
I pulled into a parking lot and proceeded to park my suburban. I hit the brake pedal and the brakes did not work. They pulsate and gave out completely. No service lights or warning light came on previous to the incident. When the brakes didn't work I tried to pump them to get them to work but nothing worked and my suburban smashed into a bush and over the curb. I just had my brake lines replaces which was quoted $1700 at my local Chevrolet dealership. I am no looking into the issues with the ABS system. *tr
NHTSA complaint #10679609
Jan 6, 2015service brakes
Chevrolet has continued to ignore the ABS brake issue within the brake control module. This is separate from their wheel sensor issue.the brake control module.has a circuit board issue which deactivates the ABS system and shows a brake and ABS light on dash.in snow today my ABS failed and I slid through an intersection narrowly missing a school bus a f$%^ing school bus.there… Read more
Chevrolet has continued to ignore the ABS brake issue within the brake control module. This is separate from their wheel sensor issue.the brake control module.has a circuit board issue which deactivates the ABS system and shows a brake and ABS light on dash.in snow today my ABS failed and I slid through an intersection narrowly missing a school bus a f$%^ing school bus.there is so much info on this issue on the internet but Chevrolet seem to be ignoring it.the problem is centered around a circuit board in the brake control module.
NHTSA complaint #10670491
Dec 2, 2014power train, service brakes, fuel/propulsion system
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the vehicle was shifted into drive and the vehicle failed to move forward. The contact also stated that the brake warning light illuminated. On another occasion while driving at approximately 5 MPH, the engine stalled without warning. The failure recurred multiple times. The vehicle was taken to an… Read more
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the vehicle was shifted into drive and the vehicle failed to move forward. The contact also stated that the brake warning light illuminated. On another occasion while driving at approximately 5 MPH, the engine stalled without warning. The failure recurred multiple times. The vehicle was taken to an independent mechanic, who diagnosed that the fuel pump needed to be replaced. The mechanic also stated that the anti lock brake system failed and unknown parts needed to be replaced. The vehicle was repaired for the anti lock brake system failure but the fuel pump was not replaced. The manufacturer was notified of the failure and informed that the VIN was not included in NHTSA campaign numbers: 05v379000 (service brakes, hydraulic) and 05v155000 (fuel system, gasoline). The approximate failure mileage was 100,000.
NHTSA complaint #10661611
Nov 4, 2014service brakes
Brake lines severely corroded and blew out. Severe corrosion under truck too. *tr
NHTSA complaint #10652446
Sep 7, 2013service brakes
The brakes failed and the pedal last all pressure and went to the floor. Was successful in stopping the vehicle from 35 MPH without incident. Upon inspection, the rear driver's side brake line was severely corroded and failed. Further inspection showed that other brake line are in the similar condition. *ln
NHTSA complaint #10542391
Jun 17, 2013service brakes
Moving my boat in the driveway and when I went to stop my brake line from the master cylinder to the ABS controller failed causing no braking!!! Pumped them like crazy and it just pissed out all of the fluid. I had my children playing in the area and I was fortunate that they were not killed! Upon inspection the brake line rotted at the points where they are held onto… Read more
Moving my boat in the driveway and when I went to stop my brake line from the master cylinder to the ABS controller failed causing no braking!!! Pumped them like crazy and it just pissed out all of the fluid. I had my children playing in the area and I was fortunate that they were not killed! Upon inspection the brake line rotted at the points where they are held onto the frame by the hangers! This is incredibly dangerous and I believe that GM should have some liability in this matter. The vehicle is barely just over 10 years old and this is a major flaw in design. The scary part is the lines look great overall but where they are placed in all of the hangers they had rot spots in them that was only apparent after dis-assembly. A normal safety inspection would not pick up on the corrosion hidden within the hangers. *tr
NHTSA complaint #10520280
May 5, 2013service brakes
While making a sudden stop, a hydraulic line serving the front brakes ruptured causing complete loss of front brakes. This is the third hydraulic brake line failure on this vehicle. The first two lines to fail were on the rear axle. All of the remaining hydraulic brake lines are heavily rusted and pitted, they all are at risk of failure at any time. This problem is widespread… Read more
While making a sudden stop, a hydraulic line serving the front brakes ruptured causing complete loss of front brakes. This is the third hydraulic brake line failure on this vehicle. The first two lines to fail were on the rear axle. All of the remaining hydraulic brake lines are heavily rusted and pitted, they all are at risk of failure at any time. This problem is widespread on this year and model vehicle. It poses a serious risk to the drivers and to the persons and property of others. Every one of the owners should be notified that their vehicle may require replacement brake lines. Whose responsibility it shall be is up to NHTSA, but the need for information is great. This is a heavy weight vehicle for ordinary consumer use. Most such users are unprepared for a brake failure of this kind. Interestingly, GM does not offer replacement parts. Precision formed lines are available on the aftermarket. The local chevy dealer uses non-corroding copper-nickel replacement line, and fabricates the lines locally. The same brake line metallurgy was used in high end european cars (volvo and porsche) beginning in the 1980s. *tr
NHTSA complaint #10510662
Mar 31, 2013service brakes
While driving on the highway at 55mph I was near my exit and activated the brakes and the pedal went to the floor. I was fortunate to have the room to change lanes and pass my exit and downshifted to slow and eventually stop. I had tried to apply the parking brake and the cable snapped on the spot. After getting the car to a mechanic I was told that every brake line was… Read more
While driving on the highway at 55mph I was near my exit and activated the brakes and the pedal went to the floor. I was fortunate to have the room to change lanes and pass my exit and downshifted to slow and eventually stop. I had tried to apply the parking brake and the cable snapped on the spot. After getting the car to a mechanic I was told that every brake line was corroded and most were failing. The mechanic also said it isn't recommended to replace just the leaking lines because once the pressure is restored, the remaining lines would then likely fail. The vehicle is currently in the shop and I am waiting for what I am sure will be a sizable repair bill. *tr
NHTSA complaint #10505131
Sep 26, 2012service brakes
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that while performing routine maintenance on the vehicle, he attempted to engage the parking brake but the vehicle continued to move. The vehicle was taken to an authorized dealer where it was confirmed that the emergency brake failed. The vehicle was not repaired. The manufacturer was contacted. The… Read more
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that while performing routine maintenance on the vehicle, he attempted to engage the parking brake but the vehicle continued to move. The vehicle was taken to an authorized dealer where it was confirmed that the emergency brake failed. The vehicle was not repaired. The manufacturer was contacted. The failure mileage was 115,700 and the current mileage was 115,736.
NHTSA complaint #10477165
Mar 20, 2012service brakes, hydraulicCrash
Tl* the contact owns a 2001 Chevrolet Suburban 1500. While driving approximately 20 MPH, the brake pedal was engaged and the vehicle failed to reduce speed. The vehicle uncontrollably crashed into a building. There was no personal injury; however there were exterior damages to the building. The vehicle sustained minor damage. A police report was not filed of the incident. The… Read more
Tl* the contact owns a 2001 Chevrolet Suburban 1500. While driving approximately 20 MPH, the brake pedal was engaged and the vehicle failed to reduce speed. The vehicle uncontrollably crashed into a building. There was no personal injury; however there were exterior damages to the building. The vehicle sustained minor damage. A police report was not filed of the incident. The vehicle was towed to an independent mechanic where the four brake lines and gear shifter cable were replaced. Also, the ABS would need to be replaced. The vehicle was previously repaired under NHTSA campaign id number: 05v379000 (service brakes, hydraulic: antilock). The failure recurred after the repair. The ABS had been replaced a total of seven times. The manufacturer was notified of the problem. The approximate failure mileage was 97,000.
NHTSA complaint #10452412
Oct 12, 2011service brakes, hydraulic, parking brake
I was driving my 2001 suburban and when I stepped on the brakes, the pedal went to the floor. No warning or brake light came on. I was able to limp the truck home and I saw the rear axle was wet with brakefluid. The left rear brake line had rotted and broke. The truck is very well kept up and I always pressure wash the undercarriage after the snow & winter. *kb
NHTSA complaint #10429959
Sep 18, 2011service brakes, hydraulic
After entering the parking lot of the local shopping center I applied the brake pedal to park in the marked space but the truck did not stop, the pedal travel all the way down but no breaking effect at all, fortunately that section of the lot was mostly empty and I let the truck roll to almost a stop, push the brake pedal again and did not stop so ended up using the parking… Read more
After entering the parking lot of the local shopping center I applied the brake pedal to park in the marked space but the truck did not stop, the pedal travel all the way down but no breaking effect at all, fortunately that section of the lot was mostly empty and I let the truck roll to almost a stop, push the brake pedal again and did not stop so ended up using the parking brake to stop the truck. No warning light ever came on so I went to check the rubber hoses and brake lines under the truck finding a brake fluid dripping from the area under the driver's seat, close to a big rubber " doughnut " ( chassis mount ). I pushed the brake pedal and fluid sprayed again from that area. There are several brake pipes running to and from a sensor or equalizing valve mounted on the chassis in that area. After towing the truck home I went under it and follow the tubing leaving from that area to the front and the rear of the truck, and it is all rusted with the exception of the flexible hoses going to the calipers. I own two other cars ( not chevy's) that are older and used under the same conditions as the suburban and the brake piping looks like new on those, so I'm inclined to think this condition is particular to suburbans or Chevrolet in general. Would this incident had not occurred in a parking lot it would have ended in an accident or a fatality. I'm calling the local chevy dealership monday to check for any outstanding recall for my truck but never received a recall notice. This
NHTSA complaint #10425959
Aug 10, 2011service brakes, hydraulicCrash
Tl* the contact owns a 2001 Chevrolet suburban. The contact stated that while attempting to park, the brakes were applied, but the pedal depressed to the floor. The vehicle continued to move forward until crashing into a median. As a result, the median moved and crashed into another vehicle head on. A police report was filed. An independent mechanic examined the vehicle and… Read more
Tl* the contact owns a 2001 Chevrolet suburban. The contact stated that while attempting to park, the brakes were applied, but the pedal depressed to the floor. The vehicle continued to move forward until crashing into a median. As a result, the median moved and crashed into another vehicle head on. A police report was filed. An independent mechanic examined the vehicle and stated that the brakes lines were completely rusted through. The manufacturer was notified and informed the contact that the vehicle was not included in the recall associated with NHTSA campaign id number 05v379000 (service brakes, hydraulic:antilock). The vehicle was in the process of being repaired. The dealer was made aware of the failure. The failure and current mileages were 110,000.
NHTSA complaint #10418336
Mar 21, 2011service brakes, hydraulic
Main brake line leak, located on top of chassis leading to rear brakes, leaked at clip point under passenger door where road salt residue can sit and corrode line. Line was also heavily rusted in other areas of line on top of chassis. Entire line needed to be replaced! *tr
NHTSA complaint #10392344
Feb 10, 2011service brakes, hydraulic
Tl*the contact owns a 2001 Chevrolet suburban k1500. The contact stated that the ABS braking system failed due to rust and a leak. While stopping at slow speeds, the brakes do not stop the vehicle and the pedal extended to the floorboard. The vehicle was taken to a local mechanic who replaced the ABS control module; reprogrammed the computer, the front hubs and the bearings on… Read more
Tl*the contact owns a 2001 Chevrolet suburban k1500. The contact stated that the ABS braking system failed due to rust and a leak. While stopping at slow speeds, the brakes do not stop the vehicle and the pedal extended to the floorboard. The vehicle was taken to a local mechanic who replaced the ABS control module; reprogrammed the computer, the front hubs and the bearings on both the right and left front wheels for $2,000. The vehicle was never taken to the dealer. The manufacturer was not contacted. The failure mileage was 78,000.
NHTSA complaint #10381400
Jan 3, 2011service brakes, hydraulic
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact was driving approximately 10 MPH when the ABS system activated independently. The contact stated that when the failure would occur, the vehicle would become increasingly difficult to stop. He called the manufacturer and was advised that his vehicle was not included in NHTSA campaign id number: 05v379000 (service… Read more
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact was driving approximately 10 MPH when the ABS system activated independently. The contact stated that when the failure would occur, the vehicle would become increasingly difficult to stop. He called the manufacturer and was advised that his vehicle was not included in NHTSA campaign id number: 05v379000 (service brakes, hydraulic:anti lock). The vehicle was not repaired and the failure became progressively worse. The failure mileage was 108,650 and the current mileage was 111,821.
NHTSA complaint #10373956
Dec 8, 2010service brakes, electric, equipment
Our 2001 Chevrolet suburban is experiencing brake problems which were supposed to be fixed during a 2005 recall of the vehicle. The car is experiencing a sudden activation of anti-lock brakes as described in recall # 05068. I have been told by GM to basically fix it out of my own pocket which I find hard to believe sine they have had recall issues with the same problem. *tr
NHTSA complaint #10369668
Sep 5, 2010service brakes, electric
I having a problem with my 2001 chevy Suburban 1500 regarding the ABS brake module control that failed, after resource its looks like many thousand of 2000-2002 have the same problem , I call GM and they saying their is no recall. If you check that issue would you think it should be a recall ? [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6). *tr
NHTSA complaint #10353948
Aug 17, 2010service brakes, hydraulic
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the anti-lock brake sensor would independently engage when driving at speeds of at least 10 MPH. When the ABS would activate it would cause an unusual increase in stopping distance. The contact previously received notification of NHTSA campaign id number: 05v379000 (service brakes, hydraulic:… Read more
Tl* the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the anti-lock brake sensor would independently engage when driving at speeds of at least 10 MPH. When the ABS would activate it would cause an unusual increase in stopping distance. The contact previously received notification of NHTSA campaign id number: 05v379000 (service brakes, hydraulic: anti-lock) but was advised by the dealer that because the vehicle was over 100,000 miles, they would not make repairs. The manufacturer was not contacted. The vehicle was not repaired. The failure mileage was 65,000 and the current mileage was 113,000.
NHTSA complaint #10349964
Aug 3, 2010service brakes, hydraulic
Huge safety issue !!!!!! 1. Vehicle maine state inspection 2. Two rear and side brake lines are severely rusted and will not pass state inspection 3. Must replace brake lines; side line replacement requires removal of 30 gallon gas tank! Have not yet repaired. *tr
NHTSA complaint #10346967
Jun 7, 2010service brakes, electric
Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6) the ABS computer on my 2001 Chevrolet suburban failed at just over 70,000 miles. I contacted chevy about this and was told it occurred often and that it wasn't covered.. I have searched the internet and have found numerous other complaints about this same issue and everyone thinks it… Read more
Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6) the ABS computer on my 2001 Chevrolet suburban failed at just over 70,000 miles. I contacted chevy about this and was told it occurred often and that it wasn't covered.. I have searched the internet and have found numerous other complaints about this same issue and everyone thinks it should be a safety recall issue. Can you please investigate this and get back in touch with me? [xxx] *tr
NHTSA complaint #10335066
Jun 5, 2010service brakes, hydraulic
2001 Chevrolet suburban brake failure due to corrosion on left rear brake line. I verified the corrosion by climbing under the truck to see what happened. This failure is not due to an accident with the truck nor has the brake line been crushed due to running over a large obstruction. The brake line is located above the vehicle frame rail. No accident occurred due to this… Read more
2001 Chevrolet suburban brake failure due to corrosion on left rear brake line. I verified the corrosion by climbing under the truck to see what happened. This failure is not due to an accident with the truck nor has the brake line been crushed due to running over a large obstruction. The brake line is located above the vehicle frame rail. No accident occurred due to this failure as it happened while exiting my driveway. I managed to stop the truck using my emergency brake. I understand there is a current investigation concerning this problem on chevy and GM trucks and suvs. I went to my local Chevrolet dealers service department but was informed that as there is no recall the expense would not be covered by GM. *tr
NHTSA complaint #10334714
May 8, 2010service brakes, hydraulic
The ABS system activated for no apparent reason, this is the first time it happened with just the pedal application, on dry pavement under 20 MPH. Activated and increased stopping distance, while keeping pedal pressure on. Luckily I try not to follow cars closely. Have had similar problems when hitting a bump, which can activate ABS system due to loss of wheel traction. It… Read more
The ABS system activated for no apparent reason, this is the first time it happened with just the pedal application, on dry pavement under 20 MPH. Activated and increased stopping distance, while keeping pedal pressure on. Luckily I try not to follow cars closely. Have had similar problems when hitting a bump, which can activate ABS system due to loss of wheel traction. It should not happen on dry pavement, and can cause an accident. GM should address this problem, I did the previous recall but I still had the problem. *tr
NHTSA complaint #10329428
Feb 21, 2010service brakes, hydraulic
Service brakes,hydraulic,antilock. *tr
NHTSA complaint #10312551
Jan 5, 2010service brakes, hydraulic
2001 chevy Suburban 1500 lt, ABS problem. Recurrence of failure of ABS pump to deactivate. Pump runs continuously until it burns up. Replaced previously (not under warranty). Over $1000. At this time the ABS fuse is pulled so pump won't burn up again, but I have no antilock brakes. Apparently a sensor or something is failing and causing an expensive repair. *tr
NHTSA complaint #10298264
Dec 28, 2009service brakes, hydraulic
The NHTSA campaign id #l 05v379000 on my 2001 Chevrolet suburban was performed in 2005 at the valenti auto mall in mystic, ct. The intent was to treat a GM recall no. 05068 to fix ABS front hub sensors that would corrode. Supposedly they did this at 85,000 miles in 2005. In 2009, I have been having recurring ABS issues and they replaced the inaccurate sensor signal at $675.… Read more
The NHTSA campaign id #l 05v379000 on my 2001 Chevrolet suburban was performed in 2005 at the valenti auto mall in mystic, ct. The intent was to treat a GM recall no. 05068 to fix ABS front hub sensors that would corrode. Supposedly they did this at 85,000 miles in 2005. In 2009, I have been having recurring ABS issues and they replaced the inaccurate sensor signal at $675. Recurring issues they now need to replace the passenger side sensor at $675. The issue is that the sensor recall did not solve the problem, GM has stated the customer must pay for the very issue the recall called out, which was corroded senor hub assemblies and the customer must pay. This has been a very dangerous condition that GM/Chevrolet knew of and did not fix in an appropriate manner. The suburban barely does not stop well at all and is very dangerous. *tr
NHTSA complaint #10297137
Aug 12, 2009service brakes, hydraulic
I own a 2001 chevy suburban. Yesterday, for the 2nd time since I have owned the vehicle the ABS light came on and stayed on. When I got home and turned off the ignition, a noise that sounded like a generator was running under the truck. We disconnected the ABS fuses both inside the truck and the engine to make the noise stop. Called chevy dealer and was informed that a… Read more
I own a 2001 chevy suburban. Yesterday, for the 2nd time since I have owned the vehicle the ABS light came on and stayed on. When I got home and turned off the ignition, a noise that sounded like a generator was running under the truck. We disconnected the ABS fuses both inside the truck and the engine to make the noise stop. Called chevy dealer and was informed that a bulletin has been issued about the ABS system, but no recalls. Was also informed it would be $1500 to fix. I had it replaced the first time in 2005. A mechanic has told us that the ABS pumps should never go bad. *tr
NHTSA complaint #10280268
Mar 6, 2009service brakes, hydraulic
I have a 2001 Chevrolet Suburban 1500. I had rear brakes and rotors replaced at 87813 miles in 02/08. At approximately 78713 miles the front brake pads were replaced. The vehicle now has approximately 104783 miles on it and the rear pads are gone and the rear rotors are warped. The front pads curiously still have 2/3 of the pad left. When going online I found a recall… Read more
I have a 2001 Chevrolet Suburban 1500. I had rear brakes and rotors replaced at 87813 miles in 02/08. At approximately 78713 miles the front brake pads were replaced. The vehicle now has approximately 104783 miles on it and the rear pads are gone and the rear rotors are warped. The front pads curiously still have 2/3 of the pad left. When going online I found a recall effecting the brake system of the vehicle NHTSA # 05v379000. Doing my due diligence I called GM customer service about the problem and they stated that this particular recall is not open for the VIN # of my vehicle. After reading the actual recall on your website it would appear my vehicle which is in fact registered in the state of ohio a "salt-belt" state which was one of the primary considerations for the recall. I am curious as to why the recall would not be in effect on my vehicle. Does my vehicle first have to be involved in an accident causing injuries because of a brake failure before this will be addressed? No common car owner would suspect that after 15k miles rear brakes would need to be replaced and would more than likely continue driving the vehicle until there was a catastrophic brake failure that could lead to serious injury. I would like someone to get an explanation from general motors as to why this is not being addressed in these vehicles not supposedly affected by this recall. *tr
NHTSA complaint #10260900
Jan 9, 2009service brakes, hydraulic
Initially purchased suburban with 61,000 mi. Had no problems with anything. I received a notice from GM for a recall on 2001's for activation of ABS braking system at slow speeds. Having no problems with it at the time I waited a few weeks before going to bergstrom chevy in neenah wi. I let them take the vehicle in the garage to do the recall work. 2 and a half hours later… Read more
Initially purchased suburban with 61,000 mi. Had no problems with anything. I received a notice from GM for a recall on 2001's for activation of ABS braking system at slow speeds. Having no problems with it at the time I waited a few weeks before going to bergstrom chevy in neenah wi. I let them take the vehicle in the garage to do the recall work. 2 and a half hours later they called me from the waiting area and said it was ready. I drove away and continued to have no problems until approx. 14 months later when the ABS started to activate at every stop at around 5mph. It continues to do this now and has since the summer of 2008. I contacted bergstrom and GM about the problem and they say they no longer do this recall work without charge. I looked at the bolt heads on the front brake calipers to see if they were marred by removal and there is no evidence that these bolts were ever removed for servicing the sensors. The facing of the bolts is still intact with no marking of any kind on these bolts so I am certain bergstrom never removed the calipers to clean the sensors. I am furious with GM and their products - I have always been a GM customer since beginning to drive in 1976 but with the products they've been producing in the last 10-15 years I will never buy another late model GM product.( I am also having issues with the intake manifold on my 1998 buick park ave - another inferior GM product) it's no wonder the company is having financial difficulty with all the comp
NHTSA complaint #10254420
Jul 18, 2008service brakes, hydraulic, electronic stability control (esc)
ABS recall 05068, clean & inspect wheel sensors, 18 nov 2005. ABS & traction control warning lights on,16 jun 2006 (55977 miles). Dealer diagnostic code c0265, ecbm ($925.59 part) and also bpmv ($761.14 part) plus approx 2hrs labor. I asked if it would be safe to disconnect the pump from the ABS system until I could see if the recall would cover this cost, it hasn't happened… Read more
ABS recall 05068, clean & inspect wheel sensors, 18 nov 2005. ABS & traction control warning lights on,16 jun 2006 (55977 miles). Dealer diagnostic code c0265, ecbm ($925.59 part) and also bpmv ($761.14 part) plus approx 2hrs labor. I asked if it would be safe to disconnect the pump from the ABS system until I could see if the recall would cover this cost, it hasn't happened as of this date. The vehicle has been in operation since this system failure. I now have learned that the relay on the ebcm that controls the power has contacts that weld closed which causes the pump to run continuously. I asked if I could have the old part when I get it fixed and was told no because it must be returned. I also feel that when I was told it may also need the bpmv that the check valve holding the pump pressure could be the true cause of system failure. I feel that people that buy this safety feature should have it work for the life of the vehicle. I also know that the repair costs have since gone up. *tr
NHTSA complaint #10234870
May 22, 2008service brakes, hydraulicCrash
Tl*the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the ABS was engaging prematurely. While attempting to park the vehicle at 5 MPH, the contact attempted to depress the brake pedal, but the vehicle did not stop. The vehicle crashed into the wall of his garage. The dealer repaired the front hubs and ABS sensors for free and the contact was… Read more
Tl*the contact owns a 2001 Chevrolet Suburban 1500. The contact stated that the ABS was engaging prematurely. While attempting to park the vehicle at 5 MPH, the contact attempted to depress the brake pedal, but the vehicle did not stop. The vehicle crashed into the wall of his garage. The dealer repaired the front hubs and ABS sensors for free and the contact was reimbursed for the damages made to his garage doors. Shortly after the repairs were made, the manufacturer issued a recall on the same defect he experienced. The contact stated that the failure recurred at 87,000 miles. The ABS light illuminated and the vehicle failed to come to a complete stop until a few seconds after the brake pedal was depressed. He called the manufacturer to notify them of the failure, but they were not willing to authorize the repair of the ABS for free. The VIN and recall number were unknown. The failure mileage was 30,000 and current mileage was 87,000.
NHTSA complaint #10228666
May 2, 2008parking brake
Tl*the contact owns a 2001 Chevrolet Suburban 1500. Upon inspection of the vehicle, the emergency brake did not function and the vehicle failed inspection. There is an open and closed investigation regarding this failure. The VIN and investigation number were unknown. The failure mileage was 68,000.
NHTSA complaint #10226506
Mar 4, 2008parking brake
I own a 2001 Chevrolet Suburban 1500 2wd 5.3l v8 with automatic transmission. This vehicle was bought new and from day one, the emergency brake has been completely ineffective in holding the vehicle when applied. A cursory check on the internet reveals that this is a widespread and very well-known problem for owners of similar GM vehicles. Visits to two separate GM… Read more
I own a 2001 Chevrolet Suburban 1500 2wd 5.3l v8 with automatic transmission. This vehicle was bought new and from day one, the emergency brake has been completely ineffective in holding the vehicle when applied. A cursory check on the internet reveals that this is a widespread and very well-known problem for owners of similar GM vehicles. Visits to two separate GM dealerships in dallas confirm that the dealers know of this as a widespread and well-known problem as well. Oddly, the NHTSA had a chance to review this vehicle safety defect at the request of the north carolina consumer council back in 2005, yet the NHTSA decided at the time that this defect did not warrant a safety recall. The summary concludes that for auto-transmission-equipped vehicles, the presence of a "park pawl" serves as sufficient holding power for these vehicles and therefore the appeal for a safety recall was denied. There is at least one major problem with this conclusion -- no state is going to allow a vehicle without a working parking brake to pass a state safety inspection. I know this first hand, at least in texas I do. It of course makes no sense for the NHTSA to have a different standard of vehicle safety than the constituent states do. Either this is an issue worthy of a national safety recall, or the lack of a working parking brake should not serve as a vehicle for failure of a state safety inspection. *tr
NHTSA complaint #10220024
Dec 17, 2007service brakes, hydraulic
The ABS electronic module failed again today. This will be my second module. The first module failed in 2004 and was replaced. The cost of replacing these has risen to over $1200.00 a pop. Why doesn't NHTSA investigate these failures? This module failure results in no ABS when you need it in a crisis situation. *tr
NHTSA complaint #10212143
Nov 7, 2007service brakes, hydraulic
ABS kicks in at speeds under 10 MPH even after recall fix in oct 2005 dealer kindly did a goodwill repair at minimal cost to me on 11/7/2007 I just want people to know this problem is recurring. *tr
NHTSA complaint #10208188