My brakes do not always work; I often have to pump the brakes up just to be able to get them to apply. It is very scary. I can put my foot all the way to the floor, and the truck will barely slow down. I feel I will likely rear-end somebody or roll into a busy intersection because the brakes will not work.
2001 Chevrolet S10 brakes problems
66 owners reported brakes problems — 21% of all 309 complaints about the 2001 Chevrolet S10.
Brakes complaints by Chevrolet S10 year
What owners report
Tl* the contact owns a 2001 Chevrolet S10. While driving various speeds and depressing the brake pedal, the vehicle failed to stop and the brake line fractured. The failure recurred numerous times. The vehicle was taken to a dealer, but the cause of the failure could not be determined. The vehicle was not repaired. In addition, the vehicle was taken to an independent mechanic… Read more
Tl* the contact owns a 2001 Chevrolet S10. While driving various speeds and depressing the brake pedal, the vehicle failed to stop and the brake line fractured. The failure recurred numerous times. The vehicle was taken to a dealer, but the cause of the failure could not be determined. The vehicle was not repaired. In addition, the vehicle was taken to an independent mechanic and the brakes were replaced. The manufacturer was not made aware of the failure. The approximate failure mileage was 99,000. The VIN was not available.
The emergency brake is missing the teeth for holding the brake in place. Also the ABS light is always on and they say it is the master that needs replacement at over $1,200. This is only a danger if using the cursor control on wet pavement which I never use due to the ABS not working.
I was turning left and another car coming from the opposite direction made a right turn in front of me and I hit my brakes and tried to stop but my ABS did not kick in and I slid about thirty feet and hit there car. *tr
Our ABS light keeps coming on and when it does the ABS don't work. It comes on whenever it wants. It is the same issues as the 2000 are having and they have a recall. It recently caused the back wheel not to move at all. We were told the spring inside the module is going out. It also affects the air bag from going on. Also, the ignition won't work the truck won't start.… Read more
Our ABS light keeps coming on and when it does the ABS don't work. It comes on whenever it wants. It is the same issues as the 2000 are having and they have a recall. It recently caused the back wheel not to move at all. We were told the spring inside the module is going out. It also affects the air bag from going on. Also, the ignition won't work the truck won't start. It takes several tries to get it to start. We were just told that it's the starter. The seatbelt locks intermittently and won't let me move. *tr
The brake lines have rotted causing brake to travel to the floor and barely stop. This is the 2nd time my brake line has failed. *tr
My 2001 S10 Chevrolet pick up ABS light has been on for ever and the brake shops and the tire store mechanics tell me there are a lot of Chevrolet trucks with this problem. The repair estimates I have received range from $1000.00 to $1500.00. After internet research I have found this is a big problem and it has to do with two solder points in the ABS control circuit board at… Read more
My 2001 S10 Chevrolet pick up ABS light has been on for ever and the brake shops and the tire store mechanics tell me there are a lot of Chevrolet trucks with this problem. The repair estimates I have received range from $1000.00 to $1500.00. After internet research I have found this is a big problem and it has to do with two solder points in the ABS control circuit board at the ABS head. Some folks take this unit apart and solder these two points and they work/repaired the problem, sometimes not. .is general motors fixing these problems?? *tr
As I was driving I was approaching a four way stop and applied the brakes any the brake pedal went to the floor. The brakes worked fine for the stop before this one. I tried to pump the brakes and the pedal still went to the floor and the vehicle finally started to slow down, I had to down shift to stop in time. I was able to get the vehicle to a firestone service station… Read more
As I was driving I was approaching a four way stop and applied the brakes any the brake pedal went to the floor. The brakes worked fine for the stop before this one. I tried to pump the brakes and the pedal still went to the floor and the vehicle finally started to slow down, I had to down shift to stop in time. I was able to get the vehicle to a firestone service station down the street. They found one of the main brake line shad corrosion and had rusted through and the brake fluid leaked out as I applied the brakes. I was lucky. I had my 2 year old son in the car at the time. I think my years of driving experience allowed me to avoid a serious collision. There was no warning about the failure of the brake lines. Also the mechanic noticed serious rusting of the rear disc backing plates, these will also need replacing. So far the cost is about $500. For just the brake lines.the truck has under 60,000 miles. I hardly drive it. *tr
The parking brake is inoperable. The rachet mechanism does not work--I.e. Does not hold the brake in a set position. Worked the prior time set on a hill 5 months earlier. *tr
ABS brake system continuously becomes inoperable and the light comes on with the red brake light. The dealer says it trash in the system and doesn't think it needs to be replaced. Now the lights stay on all the time and inspection is due. Due to this manufacturer defect, the part cost $900.00 and then labor, job will be $1300.00. I have a 2000 ford windstar van with the same… Read more
ABS brake system continuously becomes inoperable and the light comes on with the red brake light. The dealer says it trash in the system and doesn't think it needs to be replaced. Now the lights stay on all the time and inspection is due. Due to this manufacturer defect, the part cost $900.00 and then labor, job will be $1300.00. I have a 2000 ford windstar van with the same problem. Is there something that can make the manufacturer pay for the repair? This is a closed system that has never been touched or serviced. *js
Parking brake wont stay engaged when pushing pedal to the floor. *tr
Tl*the contact owns a 2001 Chevrolet s-10 pickup. After taking the vehicle in for a state inspection they found that the front brake rotors rusted very badly and had fallen apart. The vehicle was taken to the dealer who replaced the rotors and brake pads at the contacts expense. The manufacturer was contacted and offered no assistance for the repairs. The VIN was unavailable. The failure mileage was 108,000.
At low speed and when going over bumps in road the ABS system engages making it hard to stop. This has been happening for the last 5 years that I have noticed and happens everytime this situation happens. *tr
2001 Chevrolet S10 pickup with manual transmission parking brake failure foot activated parking / emergency brake fails to stay engaged leading to dangerous condition and potential injury or death. Foot activated parking brake assembly is defective, needs replacement. *tr
Brake light and ABS light come on and stay on for a while and then go off. After braking and rolling over a small bump in road at stop sign pedal loses pressure and stopping becomes hard. I rolled past stop sign and was lightly struck on passenger side door. I have investigated this problem and I am not the only one to have experienced this problem. *tr
Tl*the contact owns a 2001 Chevrolet S10. While coming to a stop, the vehicle drove over a small bump in the road, and the brake pedal extended to the floor. The brakes had to be pumped in order to stop the vehicle. The failure occurred on four separate occasions. The engine and ABS lights illuminated intermittently on the instrument panel. The vehicle was taken to a… Read more
Tl*the contact owns a 2001 Chevrolet S10. While coming to a stop, the vehicle drove over a small bump in the road, and the brake pedal extended to the floor. The brakes had to be pumped in order to stop the vehicle. The failure occurred on four separate occasions. The engine and ABS lights illuminated intermittently on the instrument panel. The vehicle was taken to a mechanic and no failures were found. The VIN was unknown. The failure mileage was 50,000.
The fuel light and service engine light and ABS light comes on won't shut off on my 2001 chevy S10 crew cab.*cn
Tl*the contact owns a 2001 Chevrolet s-10. While driving 25 MPH, the brake pedal was depressed and the brakes made a screeching sound. There were no warning indicators or friction in the brake pedal. The vehicle failed to stop and rear ended another vehicle. The road conditions were wet. The front bumper was damaged and a police report was filed. The vehicle was driven… Read more
Tl*the contact owns a 2001 Chevrolet s-10. While driving 25 MPH, the brake pedal was depressed and the brakes made a screeching sound. There were no warning indicators or friction in the brake pedal. The vehicle failed to stop and rear ended another vehicle. The road conditions were wet. The front bumper was damaged and a police report was filed. The vehicle was driven to the repair shop. The current and failure mileages were 30,000.
During rountine operation, after applying the brakes. The emer and ABS warning lights illuminated indicating a failure of the ABS brake system. After checking with my local dealership, I eas informed this is a common failure of the ABS control module and to repair the system it would cost appx 1,200.00. The very next day the lights went off and remained off for several weeks.… Read more
During rountine operation, after applying the brakes. The emer and ABS warning lights illuminated indicating a failure of the ABS brake system. After checking with my local dealership, I eas informed this is a common failure of the ABS control module and to repair the system it would cost appx 1,200.00. The very next day the lights went off and remained off for several weeks. Brakes operate normal, its impossible for the consumer to determine the exact extent of the failure and to what system. Also consider this to be a systemic problem with GM s series vehicles according to the local GM dealership. *tr
On july 22, 2005, I paid the dealer $615.74 to replace a shorted air pump. I brought it in since the light gauges were turning on. The "check engine" lighted on and off. One week later, the A/C stopped working. The dealer charged me $105.19 for the diagnosis. On aug. 10, I paid another shop $852.08 to replace the A/C compressor. On aug. 30, my s-10 stalled and hasn't… Read more
On july 22, 2005, I paid the dealer $615.74 to replace a shorted air pump. I brought it in since the light gauges were turning on. The "check engine" lighted on and off. One week later, the A/C stopped working. The dealer charged me $105.19 for the diagnosis. On aug. 10, I paid another shop $852.08 to replace the A/C compressor. On aug. 30, my s-10 stalled and hasn't worked since then. A mechanic said the engine has to be replaced (another $3000 +) due to overheating of the radiator. There was no prior indication that the radiator was leaking or heating except when the light gauges were turning on in july. I bought this truck brand new in 2000 and have spent over $7000 in repairs and regular maintenance since then. The battery acid has leaked. Brake pads keep wearing out. Several air injection malfunctions and pumps have been replaced. I've purchased at least 2 sets of tires. It has less than 72,000 miles. *jb
Dt: the contact stated when the brakes were applied the vehicle jerked. When it was explained to the dealer what the vehicle was doing they stated the rotors were warped. A diagnostic test has not been performed to specifically determine the cause of the problem. *ak updated 11/16/2005 - *nm
As our son was driving our 2001 s-10 ext cab pickup home, he came into a curve and the truck had no braking power. He said he heard a grinding noise in the vehicle and had no brakes. He went off the curve and hit a tree. The truck was totaled. My son as well as his two friends were taken to area hospitals luckily, no one was seriously injured as they had their seat belts… Read more
As our son was driving our 2001 s-10 ext cab pickup home, he came into a curve and the truck had no braking power. He said he heard a grinding noise in the vehicle and had no brakes. He went off the curve and hit a tree. The truck was totaled. My son as well as his two friends were taken to area hospitals luckily, no one was seriously injured as they had their seat belts on and were going the speed limit. I would hate to say what would have happened if they would have been traveling at a faster rate of speed. After seeing similar complaints filed by other 2001 s-10 owners, I'm wondering if someone will have to be killed before they rectify this brake problem. *jb
Contact states: last month husband couldn't go any faster then 35 MPH in a 55 MPH zone . It was like something was stopping the wheel back from moving, and it started smoking from the wheel. Took vehicle to auto zone, and they said the brake was pressing up against the wheel. They had the brake pads and calipers changed. But that did not fix the problem. They took the car… Read more
Contact states: last month husband couldn't go any faster then 35 MPH in a 55 MPH zone . It was like something was stopping the wheel back from moving, and it started smoking from the wheel. Took vehicle to auto zone, and they said the brake was pressing up against the wheel. They had the brake pads and calipers changed. But that did not fix the problem. They took the car to the dealer. They put on loaded brake pads, and redid the hoses and the calipers . However, the problem was not solved, and they claimed that contaminated brake fluid was in the hoses. There was no contaminated fluid put in the car. Insurance adjusters stated they did not see any signs of contaminated brake fluid and that it was something mechanical.*ak
Front brake rotors get hot spots and wear out pads. I have had this truck three years and have had to have the front brakes done seven times due to these hot spots. I have taken it to three dealers here in town and they say "there is nothing wrong, but we can do your front brakes for $300", I have done this three times. With in a couple months it's back to the same way it was,… Read more
Front brake rotors get hot spots and wear out pads. I have had this truck three years and have had to have the front brakes done seven times due to these hot spots. I have taken it to three dealers here in town and they say "there is nothing wrong, but we can do your front brakes for $300", I have done this three times. With in a couple months it's back to the same way it was, now if I have the brakes done again, I need to replace the rotor because they have been turned so many times.
Horrible problem with the shifting of transmission. Transmission was rebuilt 6 months ago due to the burn out of the 2nd and 3rd gear. Shifting has not changed since the rebuild. Vehicle easily slips out of gear and increasingly loses speed...no matter if the gas pedal is to the floor or not. Truck will go 65 MPH in 2nd gear with pedal to the floor and lose speed rapidly… Read more
Horrible problem with the shifting of transmission. Transmission was rebuilt 6 months ago due to the burn out of the 2nd and 3rd gear. Shifting has not changed since the rebuild. Vehicle easily slips out of gear and increasingly loses speed...no matter if the gas pedal is to the floor or not. Truck will go 65 MPH in 2nd gear with pedal to the floor and lose speed rapidly still. Second, brakes lock up going over small bumps, and then seem to not want to work properly on occasion. Lastly, tailgate cables have snapped after I sat on the tailgate (I'm 5'0" and 100lbs!!). *ak
2004 tail gate ass failed replaced after market parts 2004 back up lights in/op;004 interrior light will not turn off/ over ride botton used to save battery2005 left front hub ass replaced. 004 right front hub ass replaced;005 front end replaced/pittman/tie rods;2004 oil filter leak / tightened 2004 rear emergency brakes in/op 5 left emergency brake drum… Read more
2004 tail gate ass failed replaced after market parts 2004 back up lights in/op;004 interrior light will not turn off/ over ride botton used to save battery2005 left front hub ass replaced. 004 right front hub ass replaced;005 front end replaced/pittman/tie rods;2004 oil filter leak / tightened 2004 rear emergency brakes in/op 5 left emergency brake drum replaced;005 right emergency brake drum replaced 2005 gas sending unit replaced eradic behavior 2004 left brake shoe replaced ;004 right brake shoe replaced;005 left brake shoe replaced front;005 right brake shoe replaced front 2005 left brake shoe replaced rear;005 right brake shoe replaced rear;005 u joints replaced;04 battery replaced 2005 transmission showing signs of wear;005 rear end {3.42} locker clangs between 1st and revved. 004 4 tires 005 4 tires 2004 door hinges freeze up lube;005 tail gate hinges show wear 2005 parts 4 ea tie rods/o/ring type brake shoesand drums/u joints. I have for inspection.*ak
Brake pedal goes to the floor 60% of driving. I have had my pickup in two different Chevrolet dealership garages numerous times, but my brakes still go to the floor! *ak
With a hard application of brakes, especially over any rough surface, it appears that the antilock/skid feature fails and all braking ceases. *ak
While making a left turn, the brake hose pinched between the wheels and the frame of the vehicle. As a result brake fluid began to leak and the brakes failed. The vehicle collided head on into a parked vehicle. Please provide additional information. *jb
While driving 70 MPH consumer applied the brakes and pedal went to the floor. Consumer was able to maintain control of the vehicle and drove it home. Consumer contacted the dealer, and service manager told consumer to bring vehicle in for inspection in two business days. *ak
While braking vehicle vibrated. Dealership mechanic determined that the problem pertained to front rotors that wore out prematurely. Dealership repaired the problem before, but the problem recurred. *ak
When the vehicle was turned off, the brake vacuum leaked causing brake failure when starting the vehicle. The mechanic replaced the check valve but the problem still exists. *ak the engine died while driving,thee was not enough vacuum on the brake system to stop the vehicle. GM stated that they had a lot of problems with the check valve and booster. *sc *jb
Anti-lock brakes work sporadically, one side will lock and pull the car to that side, sometimes I press on the brake and the truck keeps going and then stops slowly, has caused me to almost get into crashes many times. *la
I owna 2001 chevy s-10 and have always noticed that the brakes, when applied going over a small bump or dip, will make a grinding noise and not engage at all. They will engage after a few seconds of applied pressure but by then I am already through the intersection and have nearly been hit/have hit another car due to this. Also, I was involved in an auto accident where I had… Read more
I owna 2001 chevy s-10 and have always noticed that the brakes, when applied going over a small bump or dip, will make a grinding noise and not engage at all. They will engage after a few seconds of applied pressure but by then I am already through the intersection and have nearly been hit/have hit another car due to this. Also, I was involved in an auto accident where I had to brake hard, but when I did the truck pulled left and rear-ended the vehicle in front of me. At the time I didn't question the brakes but now I have had constant noises and clicks from the front brakes and can push the pedal to the floor, and when I do there is a loud click. I have read 11 similar complaints and wonder if there is a major problem the public should know about. If the brakes were a cause of my accident I would like to know.
Second incident: 10/18/2000 going 15 MPH with mileage of 986.