May 16, 2024suspension, service brakes, visibility/wiper
My dad purchased my truck from the church secretary where he attended in march of 2015. At the time of purchase it only had 66,000 miles on it. The secretary’s father owned it and used it from new until 6 months before we purchased it and only used it to help feed his cows. 1. Window washer motor circuit 2. Seatbelt need’s stitched 3. The overload sticker is wrong came in… Read more
My dad purchased my truck from the church secretary where he attended in march of 2015. At the time of purchase it only had 66,000 miles on it. The secretary’s father owned it and used it from new until 6 months before we purchased it and only used it to help feed his cows. 1. Window washer motor circuit 2. Seatbelt need’s stitched 3. The overload sticker is wrong came in after we purchased the truck but my dad was sick and he passed away 3/8/2016 coated brake rotor & hub assembly (86757cr)x2 tie rod end (ncd 2693017)x2 ball joint front lower (ncd 2601130)x2 tie rod end control arm front left (ncd 2605330) tie rod end control arm and ball joint front right upper (ncp 2605329) tie rod adjusting sleeve front (ncd 2691109)x2 idler arm assembly (ncd 2683654) tie rod end outer (ncd 2683267)x2 steering center link (ncd 2721591) too much noise and when making a parking lot turn it felt and sounded like I was gonna lose my whole front end on the ground.
NHTSA complaint #11589037
Oct 29, 2019air bags, service brakesCrash1 injured
Tl* the contact owns a 2000 Chevrolet S10. While driving 26 MPH around an s curve, the brakes pedal was applied, but seized. The contact lost control of the vehicle and crashed into an embankment and creek. The air bags did not deploy. The driver was not wearing a seat belt and sustained neck, nose, and eye injuries that required medical attention. A police report was filed.… Read more
Tl* the contact owns a 2000 Chevrolet S10. While driving 26 MPH around an s curve, the brakes pedal was applied, but seized. The contact lost control of the vehicle and crashed into an embankment and creek. The air bags did not deploy. The driver was not wearing a seat belt and sustained neck, nose, and eye injuries that required medical attention. A police report was filed. The vehicle was towed to the contact's residence. The manufacturer and dealer were not contacted. The cause of the failures was not determined. The failure mileage was 230,000.
NHTSA complaint #11271790
Mar 10, 2017service brakes
Tl* the contact owns a 2000 Chevrolet S10. While driving various speeds, the brake warning indicator illuminated. Also, the vehicle failed to stop when the brake pedal was depressed to the floorboard. The failure recurred. The vehicle was taken to an independent mechanic where it was diagnosed that there was oil leaking between the brake hose and front passenger wheel. The… Read more
Tl* the contact owns a 2000 Chevrolet S10. While driving various speeds, the brake warning indicator illuminated. Also, the vehicle failed to stop when the brake pedal was depressed to the floorboard. The failure recurred. The vehicle was taken to an independent mechanic where it was diagnosed that there was oil leaking between the brake hose and front passenger wheel. The technician replaced the washer for the brake hose, but the failure recurred. The VIN was not included in NHTSA campaign number: 99v220000 (service brakes, hydraulic). The manufacturer was not made aware of the failure. The approximate failure mileage was 131,000.
NHTSA complaint #10960063
Feb 20, 2017service brakes
Parking brake mechanism failed under normal use, will no longer engage parking brake. Pedal can be pushed down but will spring back and not engage. Unknown cause.
NHTSA complaint #10955627
Feb 20, 2017service brakes
The brake lines burst while driving down the road under normal driving conditions and the brakes failed resulting in no braking power. Inspection by a mechanic determined that the brake lines had suddenly failed during braking and the fluid had drained out resulting in an immediate loss of braking power during my braking. Was driving at about 30 MPH on a city street when I… Read more
The brake lines burst while driving down the road under normal driving conditions and the brakes failed resulting in no braking power. Inspection by a mechanic determined that the brake lines had suddenly failed during braking and the fluid had drained out resulting in an immediate loss of braking power during my braking. Was driving at about 30 MPH on a city street when I started to brake and they failed, was able to stop without injury due to manual transmission engine braking and a very bad parking brake.
NHTSA complaint #10955617
Apr 23, 2015service brakes
Driving normally, pressed the brake pedal and it went to the floor; fortunately, I was close to home and no traffic that I managed to roll slowly home. Rusty brake lines causing brake fluid to leak by driver side door. Tried brakes again- totally not functional. Ironically read article about GM's problem with rusty break lines in their older model trucks. Making it a point to… Read more
Driving normally, pressed the brake pedal and it went to the floor; fortunately, I was close to home and no traffic that I managed to roll slowly home. Rusty brake lines causing brake fluid to leak by driver side door. Tried brakes again- totally not functional. Ironically read article about GM's problem with rusty break lines in their older model trucks. Making it a point to notify NHTSA that this problem affects s-10s as well as the bigger models. Conversations with friends indicate to me that this effects a lot of drivers. All GM truck owners should be alerted to problem. Under different conditions with higher speeds or traffic or pedestrians, this could have turned into a catastrophe. *tr
NHTSA complaint #10712464
Nov 25, 2014service brakes, hydraulic
2000 Chevrolet s-10 while driving the brakes just grabbed and stopped the vehicle while engine was running. *mw the consumer does not like ABS. The dealer stated it was a safety feature. *jb
NHTSA complaint #10653339
Oct 29, 2014service brakes
Applied brakes 200+ feet from stop sign. Road surface was bumpy. ABS malfunctioned and gave no braking. Stopped vehicle with hand brake with slight overshoot of stop line. Removed fuse from ABS unit and have driven since with manual braking ignoring dash warning lights indicating that ABS wasn't working. This was a problem noticed prior to this incident and occurred only when… Read more
Applied brakes 200+ feet from stop sign. Road surface was bumpy. ABS malfunctioned and gave no braking. Stopped vehicle with hand brake with slight overshoot of stop line. Removed fuse from ABS unit and have driven since with manual braking ignoring dash warning lights indicating that ABS wasn't working. This was a problem noticed prior to this incident and occurred only when brakes were applied on bumpy surfaces. *tr
NHTSA complaint #10651032
Aug 6, 2014structure, service brakes, engine
Engine failure - had to be rebuilt at app. 75000 miles - both sides of cab bottom rear rusted out - first time brake failure 2013 - put brake on to put the truck in drive no brakes front right - aug 2014 brake failure - put brake on to put in drive no brakes. *tr
NHTSA complaint #10619222
Jul 17, 2014service brakes, engine
My ABS and emergency brake lights have been on ever sense I have bought the truck (mid 2014) and I can't seem to figure out why. I have read several places that say that some of the solder points in the ABS module have probably cracked and need to be repaired if it throws a certain code (and mine does). Haven't had the time or money to fix the problem as my truck is my daily… Read more
My ABS and emergency brake lights have been on ever sense I have bought the truck (mid 2014) and I can't seem to figure out why. I have read several places that say that some of the solder points in the ABS module have probably cracked and need to be repaired if it throws a certain code (and mine does). Haven't had the time or money to fix the problem as my truck is my daily driver. Have noticed some slight pulsing in the brakes when stopping, but not enough to annoy you. The lights on the dash will annoy you though. I have also been chasing several vacuum leaks. One was by the brake master cylinder and another (from inside the cab) sounds like it's right above the transmission housing at the back of the engine (where you can't see). It's so bad that when I first start the engine and start to drive at 1/2 throttle, it has absolutely no power, but then picks back up again after about a 1/4 mile with no power. Because of the vacuum leak, I'm guessing, it sounds like I have a turbo on the truck from inside the cab. If you turn the radio off, you can definitely hear it. *tr
NHTSA complaint #10611156
May 1, 2014service brakes, hydraulic
2000 Chevrolet s-10. Consumer writes in regards to anti-lock brake system recall. *smd the consumer stated he experienced the exact failure, as described in the recall, he found. However, GM refused to honor the recall. *jb
NHTSA complaint #10584857
Nov 26, 2013service brakes
Went to slowdown to turn into a business and the brakes failed due to a center brake line blown that feeds the rear brakes. *tr
NHTSA complaint #10553833
Sep 3, 2013service brakes
Tl* the contact owns a 2000 Chevrolet S10. The contact stated that while driving 20 MPH, the brakes seized. In addition, the vehicle became resistant to acceleration attempts as the ABS warning light illuminated. The vehicle was not repaired and the manufacturer was notified. The approximate failure mileage was 70,000.
NHTSA complaint #10538597
Feb 9, 2012service brakes, hydraulic, exterior lighting, structure
I have problem with my (ABS) and my tailgate. *tr
NHTSA complaint #10447227
Mar 28, 2011service brakes, hydraulic
Tl* the contact owns a 2000 Chevrolet S10. The contact stated that while driving at 5 MPH and attempting a u-turn, the brakes began to loose pressure abnormally. In order to gain control of the vehicle, he continued to pump the brakes until they returned to normal operation. The manufacturer was contacted and they advised him that there were no current recalls on the… Read more
Tl* the contact owns a 2000 Chevrolet S10. The contact stated that while driving at 5 MPH and attempting a u-turn, the brakes began to loose pressure abnormally. In order to gain control of the vehicle, he continued to pump the brakes until they returned to normal operation. The manufacturer was contacted and they advised him that there were no current recalls on the particular component. The vehicle was inspected by a dealer and they advised him that the electronic ABS would need replacing to correct the failure. The vehicle was not repaired. The failure mileage was approximately 80,000.
NHTSA complaint #10393129
Apr 12, 2010service brakes, hydraulicCrash1 injured
Approaching an on-ramp, attempted to stop, loss of brake functionality. Resulted in a crash. One person was ambulanced to hospital. The mechanic later found that the brake line was ruptured. I received a ticket. I kept the brake line. *tr
NHTSA complaint #10325134
Oct 27, 2008service brakes, hydraulic
My 2000 Chevrolet started to activate the ABS when stopping, but only within the last 5 MPH before stopping, I did some research and found that this was a known issue and there is currently a tsb, 020525006, open for the issue. Is followed the tsb as I am mechanically inclined, test drove the truck and nearly ran into the wall on the back side of my garage. I pulled the… Read more
My 2000 Chevrolet started to activate the ABS when stopping, but only within the last 5 MPH before stopping, I did some research and found that this was a known issue and there is currently a tsb, 020525006, open for the issue. Is followed the tsb as I am mechanically inclined, test drove the truck and nearly ran into the wall on the back side of my garage. I pulled the fuse to the ABS module and the truck stops without any issue. I also found a recall for all of the Chevrolet full size trucks, model year 1999-2002. The description of the issue is the exact same as the issue I am dealing with. I also found out that the brake configuration is the same as the full size trucks. There are S10's with a different configuration, but mine is the same as the full size trucks. I am currently driving with the ABS disconnected. To get the vehicle inspected, I am going to put it back in so that I can get the truck inspected as I do not have the time to get it fixed. The fix for this I believe is to have the hub replaced as that is where the corrosion exists. *tr
NHTSA complaint #10246869
Jan 28, 2008parking brake
Parking brake no longer latches. *tr
NHTSA complaint #10216293
Oct 30, 2007service brakes, hydraulic
Tl*the contact owns a 2000 Chevrolet S10. The contact stated that both rear wheels on the four wheel ABS independently lock and stick. Speed was not a factor. The brake pedal extends to the floor when depressed and does not release. The vehicle was taken to the dealer for inspection, but they could not determine the cause of the failure. The dealer stated that the… Read more
Tl*the contact owns a 2000 Chevrolet S10. The contact stated that both rear wheels on the four wheel ABS independently lock and stick. Speed was not a factor. The brake pedal extends to the floor when depressed and does not release. The vehicle was taken to the dealer for inspection, but they could not determine the cause of the failure. The dealer stated that the calipers and brake fluid level were fine. The VIN was not included in NHTSA campaign id number 00v055000 (service brakes, hydraulic:antilock). The current mileage was 81,578 and failure mileage was 81,078.
NHTSA complaint #10207392
Dec 6, 2006service brakes, hydraulic
Dt*: the contact stated while driving various speeds on wet roads with brake pressure applied, there was a longer braking distance. The dealer was contacted. Updated 2/12/2007 - the failure always occurred on snow covered roads. The consumer also indicated that the brake pedal vibrated and that there was a loud groaning noise. The vehicle was taken to the dealer but they… Read more
Dt*: the contact stated while driving various speeds on wet roads with brake pressure applied, there was a longer braking distance. The dealer was contacted. Updated 2/12/2007 - the failure always occurred on snow covered roads. The consumer also indicated that the brake pedal vibrated and that there was a loud groaning noise. The vehicle was taken to the dealer but they were unable to duplicate the problem. *nm
NHTSA complaint #10175314
Sep 25, 2006service brakes, hydraulicCrash
Dt*: the contact stated while driving 5 MPH and applying the brakes, the pedal became locked by the ABS system. This caused the pedal to pulsate as if it was sliding on ice, but the roads were dry. The defect also created an increased stopping distance. The vehicle ended up crashing into guardrails which caused damage to the front side of the truck. A police report was… Read more
Dt*: the contact stated while driving 5 MPH and applying the brakes, the pedal became locked by the ABS system. This caused the pedal to pulsate as if it was sliding on ice, but the roads were dry. The defect also created an increased stopping distance. The vehicle ended up crashing into guardrails which caused damage to the front side of the truck. A police report was taken. The vehicle was taken to the dealer who determined that there was a defect in the ABS system causing the pedal to lock. There was a recall #05v379000 regarding the service brakes:hydraulic:antilock, however the vehicle was not included in the recall due to the VIN.
NHTSA complaint #10169243
Jul 1, 2006service brakes, hydraulic
Within the last couple of weeks whenever I am coming to a stop at slow speeds, less than 10 MPH, my anti lock brakes do not allow the vehicle to stop. I have gone into a number of intersection and pass stop signs. This happens in reverse or drive. I have removed the ABS fuse and have not had any problems. Now my ABS light stays on but the vehicle stops. The dealer said… Read more
Within the last couple of weeks whenever I am coming to a stop at slow speeds, less than 10 MPH, my anti lock brakes do not allow the vehicle to stop. I have gone into a number of intersection and pass stop signs. This happens in reverse or drive. I have removed the ABS fuse and have not had any problems. Now my ABS light stays on but the vehicle stops. The dealer said that the front hub bearing assy's are loose but the longtime repair shop I always go to can find nothing wrong with the bearing assy's. I think there is rust and corrosion on the brake sensor mounting surface and have a copy of a tsb to give to my garage to hopefully try and correct this potentially dangerous problem. *nm
NHTSA complaint #10161183
May 18, 2006service brakes, hydraulic, structure
Dt*: the contact stated the ABS warning light illuminated and there was an increased stopping distance while applying brake pressure at various speeds. There is a NHTSA recall, # 00v055000, regarding the antilock brakes. The vehicle was not inspected by the dealer. The VIN was not included in the recall. Additionally, the tailgate support cables corroded and fractured… Read more
Dt*: the contact stated the ABS warning light illuminated and there was an increased stopping distance while applying brake pressure at various speeds. There is a NHTSA recall, # 00v055000, regarding the antilock brakes. The vehicle was not inspected by the dealer. The VIN was not included in the recall. Additionally, the tailgate support cables corroded and fractured without warning. The contact replaced the tailgate cables. There is NHTSA recall # 06v066000, regarding the tailgate hinge and attachments. The VIN was not included in the recall.
NHTSA complaint #10157780
Mar 22, 2006service brakes, hydraulicCrash1 injured
When brakes applied at low speed they did not work. The pedal went to the floor with no stopping . The system was inspected by medved Chevrolet and nothing was found wrong. This has happen once . The incident is very similar to the silverado recall 05v379000. I also own a silverado. *jb
NHTSA complaint #10153397
Feb 9, 2006service brakes, hydraulic
Dt*: the contact stated after purchasing a used vehicle that already had the ABS light illuminated, the ABS engaged at speeds of 10mph or less. The vehicle was inspected by the dealer. The entire ABS control module was replaced. Afterwards the problem continued, but no further repairs were made.
NHTSA complaint #10149851
Sep 29, 2005service brakes, hydraulic
Dt: contact stated the brakes on vehicle were defective. The rear caliper seal was ripped by rust, and the front brake pads were frozen in the caliper. The fluid ran out of the back brakes. The contact first noticed this in the spring, and he had to put on new brake pads. The contact wanted to report this because he did not want anyone to get hurt. *ak *nm
NHTSA complaint #10135095
Sep 29, 2005service brakes, hydraulic
Dt: while driving at a low speed, about 5 MPH, owner went to a fast food line and pushed the brakes and the pedal was stiff. There was a pulsation in the brakes, and extended stopping was required. Owner had to pull out of line to keep vehicle from hitting the car in front. The owner then pushed the brakes, and they worked just fine. The problem only occurred when the owner … Read more
Dt: while driving at a low speed, about 5 MPH, owner went to a fast food line and pushed the brakes and the pedal was stiff. There was a pulsation in the brakes, and extended stopping was required. Owner had to pull out of line to keep vehicle from hitting the car in front. The owner then pushed the brakes, and they worked just fine. The problem only occurred when the owner was going at slow speeds. The problem happened in all weather and road conditions. The owner was aware that there was a known problem with the ABS sensor, and was wondering when the recall will take place. *ak *nm
NHTSA complaint #10133031
Aug 31, 2005service brakes, hydraulic
(1) driving on a dry, sunny, summer day. I was braking for a stop sign. (2) ABS kicked in unexpectedly when vehicle slowed to somewhere below 10 MPH. This had happened before, but this time it nearly prevented the vehicle from coming to a stop. Almost caused me to enter a busy intersection with cross traffic approaching. (3) ABS was disabled by removing the appropriate… Read more
(1) driving on a dry, sunny, summer day. I was braking for a stop sign. (2) ABS kicked in unexpectedly when vehicle slowed to somewhere below 10 MPH. This had happened before, but this time it nearly prevented the vehicle from coming to a stop. Almost caused me to enter a busy intersection with cross traffic approaching. (3) ABS was disabled by removing the appropriate fuse. No further action taken. However I recently noticed the similarity between this incident and the symptoms described in NHTSA campaign id number : 05v379000 for full-size chevy trucks. *nm
NHTSA complaint #10134985
Jun 2, 2005service brakes, hydraulic
I am having the same problems with my antilock brakes as other GM trucks are having with the exception that I have an s-10 instead of a fullsize truck as mentioned in the newspaper article from may 27 in the detroit news. I would like to know if there is going to be anyone looking into the s-10 of having the same problem. I have had three near misses of an accident at slow… Read more
I am having the same problems with my antilock brakes as other GM trucks are having with the exception that I have an s-10 instead of a fullsize truck as mentioned in the newspaper article from may 27 in the detroit news. I would like to know if there is going to be anyone looking into the s-10 of having the same problem. I have had three near misses of an accident at slow speeds and every time its the same problem. I really think GM needs to address this problem before somebody gets seriously hurt. Thank you in advance for your help.
NHTSA complaint #10123942
May 21, 2005service brakes, hydraulic
Chevy s-10 p/u 2000. Brakes chatter and fail. It has been present since buying vehicle.
NHTSA complaint #10121788
May 20, 2005service brakes, hydraulicCrash2 injured
Driving 45 MPH, car suddenly stopped in front of my daughter (driver), applied brake which went to the floor and did not stop vehicle resulting in collision with vehicle and extensive damage to our S10 front; air bags did not deploy.
NHTSA complaint #10121732
May 4, 2005service brakes, hydraulic
My 2000 s-10 pickup anti-lock brakes have ben actuating at low sppeds since I purchased the truck new. Whne slowing to a stop, the system pulses the pedal if I hit a bump. The brakes also pulse when turing sharply into a parking space. Braking disatance is always extended when this happens. I have had several close calls. The dealer said that was the way it was supposed to operate.
NHTSA complaint #10119719
Feb 23, 2005service brakes, hydraulic, engine and engine cooling
Brake line failed at an intersection, total loss of brake pressure. Chevrolet notified, dealer could not find problem, part took a week to arrive, and we just fixed it at home out of exaspiration for the dealer, chevy was great though, line found worn right through. Many failures with this vehicle. Went through 3 batteries and 2 alternators. Upper ball joint failed on the… Read more
Brake line failed at an intersection, total loss of brake pressure. Chevrolet notified, dealer could not find problem, part took a week to arrive, and we just fixed it at home out of exaspiration for the dealer, chevy was great though, line found worn right through. Many failures with this vehicle. Went through 3 batteries and 2 alternators. Upper ball joint failed on the highway, parts department tried to say because it wasnt greased, but I keep it greased, the ball broke right out the side, all ball joints replaced. Idler arm found broken when vehicle taken for re-alignment before that. Various electrical failures (suspected short somewhere as battery sparks when reconnected). Fuel pump failure at 65,000 miles, preceeding fuel guage malfunction about 6 mo's before, replaced fuel pump. Heating failure suspected due to dex-cool coolant (coolant solidifies and jams heater core, ect...), vehicle reverse flushed, and new thermostat installed, not much improvement, blows harder but still cold. Transmission slips on occasion. Currently leaks steering fluid, this has not been corrected as I bought a new truck, and have not had time to fix the S10. Water coming in from somewhere, carpet consistently soaked. Very unhappy with vehicle with so many repairs, truck only has 70,000 miles, components failed far before their time, more minor things wrong but repaired. We are lucky to have a garage and a whole lot of tools for this vehicle. *ak
NHTSA complaint #10112075
Oct 25, 2004service brakes, hydraulic
While appying brakes at 40 MPH brake pedal went to the floor, and the vehicle continued to move, resulting in extended stopping distance. Dealer was not notified. *ak
NHTSA complaint #10097584
Sep 14, 2004service brakes, hydraulic, power train
While driving at any speed and when the brakes were depressed there was extended stopping distance. A certified mechanic found that the brakes were wearing out too frequently for this type of vehicle. *ak the consumer stated that the brakes are to weak to stop the large vehicle. At 61,000 miles the consumer drove the vehicle 2wd when the 4wd activation failed causing 900.00 in damage. *tc
NHTSA complaint #10083667
Aug 29, 2002service brakes, hydraulic, vehicle speed controlCrash1 injured
I was parking my truck in my apt parking structure after work on 9/14/02, upon finding a parking space I made a 3 point turn to get into the parking space. I reversed then stopped and placed the truck in drive as I was about to pull forward into the parking space. At that point I barely touch the gas expecting to coast into the space and then suddely the motor just started… Read more
I was parking my truck in my apt parking structure after work on 9/14/02, upon finding a parking space I made a 3 point turn to get into the parking space. I reversed then stopped and placed the truck in drive as I was about to pull forward into the parking space. At that point I barely touch the gas expecting to coast into the space and then suddely the motor just started revving up. I didn't think twice and just jumped on the brake with both feet but the truck wouldn't stop. We ended up jumping the cement parking stopper on the ground, which lifted the front end into the air about 2-3 feet, and sent us smashing into the block wall directly infront of us. I now have $2,200 worth of front end damage, and am really worried about driving that truck again.*ak
NHTSA complaint #766427
Feb 15, 2002service brakes, hydraulic, air bagsCrash
My son went over a bridge and the brakes made a loud noise, engaged and caused him to fishtail and run his front end into the bridge. He had a witness behind him that saw the whole thing and said it was very scary and a good thing there was no oncoming traffic. It did $2300 worth of damage and his airbags did not employ. *ak
NHTSA complaint #758282
Jan 2, 2002service brakes, hydraulic, air bagsCrash
While driving 40- 60mph applied brakes and vehicle did not slow down, causing a collision. Air bags did not deploy.*ak
NHTSA complaint #8001341
Jan 2, 2002service brakes, hydraulicCrash
While driving 40- 60 MPH and applying brakes, brake pedal was pushing foot up and did not slow vehicle down, causing consumer to have a collision.*ak
NHTSA complaint #8001340
Nov 1, 2001service brakes, hydraulicCrash
Brakes at any given moment will fail to engage and then the brake will go to the floor and anti-lock will come on. Vehicle will not stop in time.*ak
NHTSA complaint #753982