Aug 14, 2023power train, electrical system, engine
Happened twice within a day. The main electric fan on the radiator stopped working and the car overheated. Once at idle, was able to shut the car off safely. The second time, there was traffic on the highway, and the fan stopped working and the car started to overheat. Had to shut the car off and wait for it to cool down on the side of the road. When I got the car home, I… Read more
Happened twice within a day. The main electric fan on the radiator stopped working and the car overheated. Once at idle, was able to shut the car off safely. The second time, there was traffic on the highway, and the fan stopped working and the car started to overheat. Had to shut the car off and wait for it to cool down on the side of the road. When I got the car home, I found the electrical connector of the fan to be melted and fused together. There was no indicator that the fan would stop running prior to the engine overheating.
NHTSA complaint #11538312
Sep 13, 2020power train
When I start my Corvette and attempt to shift my automatic transmission from park to drive, the shifter will not move out of the park position.
NHTSA complaint #11354801
Apr 30, 2020power train, engine
When driving the vehicle, I can hear, as it seems to me, excessive valve train noise.
NHTSA complaint #11322822
Apr 6, 2020power train, engine
I was driving in s 35 MPH zone and it changed to 45 MPH. I was in 2 or 3rd gear and has just started up a slight incline and I was increasing speed when the car made a sudden jerk and loud almost a bang. I depressed the clutch and it stayed on the floor. I though that the clutch had came apart and I pulled the pedal up to see what was going on. The engine at that point… Read more
I was driving in s 35 MPH zone and it changed to 45 MPH. I was in 2 or 3rd gear and has just started up a slight incline and I was increasing speed when the car made a sudden jerk and loud almost a bang. I depressed the clutch and it stayed on the floor. I though that the clutch had came apart and I pulled the pedal up to see what was going on. The engine at that point was running very rough and would not hold speed or accelerate. I pulled into a parking lot and got my wife to pick me up. I then got my pickup and trailer and took the car to classic Chevrolet. They found where the valve had dropped into the cylinder and caused damage to the piston and rod. I looked at the engine while tore down and noticed what appeared to me to be a crack in the cylinder wall and pointed it out, the forman said the had checked it and didn't feel that it was a crack. They advised me to get a new head and have the other head worked on as well as a piston, etc. I did that and had the car repaired. When the car jerked it also affected the pressure plate so I had that replaced. After I got the car back I noticed it was smoking white vapor whenever I started it. I took it back to the dealership and the tested it and sure enough it was a crack in the cylinder. I then had the motor replaced and the dealership was very fair and credited the earlier work against the motor. When the motor let loose, the car locked the back wheels and the car behind me had to make a rather quick stop and d
NHTSA complaint #11320338
Jul 24, 2019power train
The shifter is connected to the transmission with a 4 foot cable, this cable is housed in the drive shaft tunnel, the cable has a plastic bushing on both ends, the heat in the tunnel bakes the plastic bushing that connects the shifter to the transmission cable, my bushing broke into pieces and the car could not shift into or out of gear. Many corvettes in the c5,c6 & c7 modes… Read more
The shifter is connected to the transmission with a 4 foot cable, this cable is housed in the drive shaft tunnel, the cable has a plastic bushing on both ends, the heat in the tunnel bakes the plastic bushing that connects the shifter to the transmission cable, my bushing broke into pieces and the car could not shift into or out of gear. Many corvettes in the c5,c6 & c7 modes have this same issue and are failing everyday. My car was in the garage in park, I had driven it earlier in the day, I stared the car and the shifter would move, but the plastic bushing had broken into pieces due to the heat failure. I know of the happening to 4 other corvettes and the shop I took my car to was receiving other calls on the same issue.
NHTSA complaint #11234630
Jun 27, 2019power train
Car will refuse to shift out of park during normal start. Car will refuse to shift out of park when in acc mode. Problem is non deterministic and may be related to voltages and/or resistances and/or faulty parts in system. Car is rendered non-operable and requires towing or repeated attempts to release gear train over a variable period of time. This seems to be a well known… Read more
Car will refuse to shift out of park during normal start. Car will refuse to shift out of park when in acc mode. Problem is non deterministic and may be related to voltages and/or resistances and/or faulty parts in system. Car is rendered non-operable and requires towing or repeated attempts to release gear train over a variable period of time. This seems to be a well known manufacturing defect not addressed by the manufacturer
NHTSA complaint #11223021
May 6, 2019power train
Automatic transmission shift lock solenoid fails, preventing trans. To lock into park and or can't place transmission in park. GM corrected this condition starting with VIN number 75405780, VIN numbers before that still continue to have this safety condition
NHTSA complaint #11205667
Apr 29, 2019power train
Shifter stiff and is very hard to shift into gear on automatic transmission
NHTSA complaint #11204560
May 2, 2018power train, electrical system, unknown or other
My automatic shifter jammed in the d location and would only go to neutral and would not go into reverse or park, and the doors would not open with the button, this shifter has jammed in park in the past. This car only has 26k miles on it. And is not driven in bad weather. Not a good feeling to be traped in your car.
NHTSA complaint #11091419
Jan 26, 2018power train
Vehicle would not shift in park or reverse and drive. Malfunction car was in traffic
NHTSA complaint #11065005
Aug 8, 2017power train
The shift level on my automatic transmission locks in nuetral. Been reading that this is a safety concern. It starts when the car is in park and then won't let the shifter move
NHTSA complaint #11013789
Jun 23, 2017power train
Tl* the contact owns a 2006 Chevrolet Corvette. While attempting to drive out of the driveway, the clutch pedal traveled to the floorboard. The vehicle was taken to williams Chevrolet (2 automotive blvd, elkton, md 21921) where it was diagnosed that the clutch plate, pressure plate, and slave cylinder failed and needed to be replaced. The vehicle was repaired. The manufacturer… Read more
Tl* the contact owns a 2006 Chevrolet Corvette. While attempting to drive out of the driveway, the clutch pedal traveled to the floorboard. The vehicle was taken to williams Chevrolet (2 automotive blvd, elkton, md 21921) where it was diagnosed that the clutch plate, pressure plate, and slave cylinder failed and needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure and stated that they would not assist. The failure recurred while driving 55 MPH. The vehicle was towed to a storage facility. The contact did not contact or take the vehicle to a dealer or mechanic. The manufacturer was made aware of the failure and stated that the contact should take the vehicle to a dealer and have it diagnosed. The vehicle was not repaired. The approximate failure mileage was 21,229 for the first failure and 24,000 for the second failure.
NHTSA complaint #11000865
Feb 11, 2017power train
Waiting in traffic due to accident ahead. Shift auto trans. Into park. The trans. Would not shift out of park to resume normal operation. Problem described in owner operations manual. Finally able to shift to drive. Now will not shift out of drive creating potential for car to roll without break applied. Research shows this is happening in years 2005 to 2016.
NHTSA complaint #10953979
Nov 8, 2016power train
Tl* the contact owns a 2006 Chevrolet Corvette. The contact stated that the vehicle failed to shift into the park or reverse position without warning. The vehicle was not diagnosed or repaired. The contact had to disconnect the battery in order to shut off the vehicle. The manufacturer was not made aware of the failure. The failure mileage was approximately 51,000.
NHTSA complaint #10925033
Oct 10, 2016power train
After initial start, and while holding brake pedal down, the automatic shift lever stays locked in "park," and cannot be shifted to other gears. The solenoid seems not to be engaging. This is an annoying occurrence, which happens too often. I can see safety issues arising from this problem. Problem began @ 2,500 miles. Vehicle now has only 3,100 miles, and still… Read more
After initial start, and while holding brake pedal down, the automatic shift lever stays locked in "park," and cannot be shifted to other gears. The solenoid seems not to be engaging. This is an annoying occurrence, which happens too often. I can see safety issues arising from this problem. Problem began @ 2,500 miles. Vehicle now has only 3,100 miles, and still occurring. Vehicle is always stationary, and mostly occurs during initial start, when operation of vehicle begins. Also occurs after a few hours of vehicle operation, when parked, ignition turned off, then restarted minutes or hours later. Vehicle is always garaged, and this problem is not weather related.
NHTSA complaint #10915128
Jun 27, 2016power trainCrash
1st the plastic bushing that holds the shift cable to the transmission shift linkage broke and left the car inoperable ( unable to shift ) parked in my carport about 4 moths ago , 2nd the plastic bushing that holds the shift cable to the center console shifter broke and left my car in reverse and took off and rolled back into carport with both doors open , needless to say… Read more
1st the plastic bushing that holds the shift cable to the transmission shift linkage broke and left the car inoperable ( unable to shift ) parked in my carport about 4 moths ago , 2nd the plastic bushing that holds the shift cable to the center console shifter broke and left my car in reverse and took off and rolled back into carport with both doors open , needless to say what happened I've only seen in the movies until now , both doors are totaled , and Chevrolet knows this to be a problem but does not fix cheap plastic bushings , only offers whole cable with same cheap plastic bushings ...
NHTSA complaint #10877026
Apr 7, 2016power train
Tl* the contact owns a 2006 Chevrolet Corvette. After the vehicle was started, it failed to shift from the park position without warning. The shifter cable was replaced, but the failure recurred. The manufacturer was made aware of the failure. The failure mileage was 74,000.
NHTSA complaint #10854115
Mar 14, 2016power train
Automatic transmission shifter stuck in park. In the 2006 model both of these issues will eventually lead to being "stuck in park" and you cannot control when or where. It is a known issue with GM and they have failed to issue a recall because of the cars age. It is starting to effect newer models and likely the same or similar part. The safety locking solenoid goes bad, and… Read more
Automatic transmission shifter stuck in park. In the 2006 model both of these issues will eventually lead to being "stuck in park" and you cannot control when or where. It is a known issue with GM and they have failed to issue a recall because of the cars age. It is starting to effect newer models and likely the same or similar part. The safety locking solenoid goes bad, and the part is not replaceable on its own. You have to buy an entire shifter assembly. It will cost upwards of 700.00 or more. If you force it into gear you can also break the shifter cable at a higher cost.
NHTSA complaint #10849563
Mar 13, 2016power train
Automatic shifter will not return to park or reverse position from neutral. Essentially vehicle is stuck in neutral. The failure is in the shifter mechanism and not the linkage or transmission. There is no way to safely park the vehicle in this condition or restart the car once it has been turned off. Once in this bad state, the vehicle remains in accessory mode therefore killing the battery.
NHTSA complaint #10846300
Feb 5, 2016power train, fuel/propulsion system
Has crack on top of fuel pump spraying gas , smells in cab
NHTSA complaint #10824581
Nov 5, 2015power train
Tl* the contact owns a 2006 Chevrolet Corvette. While approaching a stop, the gear shifter was not able to shift out of the drive position. The contact mentioned that the brakes were applied to stop the vehicle's movement before attempting to shift the gear shifter. The contact mentioned that the gear shifter became loose after changing position to park. The vehicle was towed… Read more
Tl* the contact owns a 2006 Chevrolet Corvette. While approaching a stop, the gear shifter was not able to shift out of the drive position. The contact mentioned that the brakes were applied to stop the vehicle's movement before attempting to shift the gear shifter. The contact mentioned that the gear shifter became loose after changing position to park. The vehicle was towed to the dealer for diagnostic testing where it was confirmed that the gear shift cable was fractured and needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure. The failure mileage was 12,211.
NHTSA complaint #10788629
Aug 15, 2015power train, fuel/propulsion system
On august 13, 2015, my 2006 Corvette would not shift out of reverse. The car was stuck in that reverse gear and the shift lever was not enabling the selection of another gear. The shifter mechanism on this automatic equipped vehicle was operational, but the linkage to the transmission was no longer engaged. The car was being pulled into the garage when this happened, so… Read more
On august 13, 2015, my 2006 Corvette would not shift out of reverse. The car was stuck in that reverse gear and the shift lever was not enabling the selection of another gear. The shifter mechanism on this automatic equipped vehicle was operational, but the linkage to the transmission was no longer engaged. The car was being pulled into the garage when this happened, so fortunately I was not in a busy intersection, in a parking lot, or in some other location where I, or someone else, might have been in harm's way due to a vehicle that I could no longer control. Since the car could not be put in neutral or park, I had to turn off the vehicle with it in reverse and use the parking brake to keep the car from moving. Since the shifter mechanism could still move, the switch activating the "ok to start" would have allowed the car to start when put in the park or neutral positions - while the transmission was still stuck in reverse; a real safety issue. The cause of the problem was a 50 cent bushing that attaches to the shift lever. This bushing allows the ball end connector of the shifter to engage a shifter cable that actuates the linkage to the transmission. So when that bushing breaks, you can no longer shift the car. This has happened to many, many people owning the generations of c5 (1997-2004) and c6 (2005-2013) corvettes. You can read a sample thread with pictures here: http://www.corvetteforum.com/forums/c6-Corvette-general-discussion/3482107-c6-automatic-shifter-broken-
NHTSA complaint #10748917
Aug 8, 2015power train
Have excessive noise coming from valve train.called Chevrolet customer service to inquire about cause and information about repair.was told no known problems and vehicle was no longer under warrantyi took car to katech in michigan to have the motor checked and repaired if needed.the clearance on the valve guides were way beyond GM spec and had deformed my valves weakening… Read more
Have excessive noise coming from valve train.called Chevrolet customer service to inquire about cause and information about repair.was told no known problems and vehicle was no longer under warrantyi took car to katech in michigan to have the motor checked and repaired if needed.the clearance on the valve guides were way beyond GM spec and had deformed my valves weakening them to the point of certain failure.I payed thousands of dollars to repair.I do not feel that a car with so liitle miles should need such an expensive repair.Chevrolet has refused to acknowledge this problem that if left unchecked would lead to engine failure resulting in an unsafe condition for driver passenger and other motorists. .
NHTSA complaint #10747174
Jun 29, 2015power train
Vehicle will not shift to park after starting engine and engaging the brake. Tried restarting and shifting the car into reverse several times and it finally went into reverse after approximately 10 minutes of trying. The vehicle was on a flat surface. After reading news and forum articles, this seems to be a commonly known problem, with the only fix being to replace the… Read more
Vehicle will not shift to park after starting engine and engaging the brake. Tried restarting and shifting the car into reverse several times and it finally went into reverse after approximately 10 minutes of trying. The vehicle was on a flat surface. After reading news and forum articles, this seems to be a commonly known problem, with the only fix being to replace the shifter assembly. GM does not however want to address this. This should be a recall item.
NHTSA complaint #10731029
Apr 23, 2015power train, electrical system
Car would not shift out of park. *tr
NHTSA complaint #10712501
Jul 21, 2014power train
First incident 15000 miles, second incident 38000 miles. Automatic transmission does not go into park. Locked in neutral or drive only. Transmission cable or reverse lock out solenoid goes bad. Will not start in neutral. Car cannot be placed into park and must be left in a neutral mode until car is transported to service center for repairs. *tr
NHTSA complaint #10614895
Jun 12, 2014power train
After starting car, it had trouble shifting in gear. After pulling on gear selector, it went in drive, but wouldn't go in reverse or park. The car wouldn't come out of accessory power mode, and I wasn't able to park the car on a hill as it had to stay in neutral or drive. There is no way to secure the car when this happens. The repair shop tells me this is a common issue on these cars. *tr
NHTSA complaint #10597983
May 20, 2014power train
I noticed that there's a recall on a number of GM cars due to a shift cable problem. I've known a number of fellow Corvette owners, with the year model 2005 thru 2009, that have had the cable break. I just wanted to make the NHTSA aware of the problem in case you've seen more complaints regarding it and a recall might be warranted. *tr
NHTSA complaint #10592854
Apr 18, 2014power train, electrical system
Car sticks in park. Will not go in gear. *tr
NHTSA complaint #10583464