CarProblemsDB

2000 Chevrolet Corvette electrical system problems

24 owners reported electrical system problems — 9% of all 277 complaints about the 2000 Chevrolet Corvette.

Electrical system complaints by Chevrolet Corvette year

20251
20245
20237
20227
20214
20203
20192
20181
20174
20166
20155
20148
20134
20126
20113
20105
20098
200839
200735
200644
2005101
200411
200315
200217
200125
200024

What owners report

Feb 1, 2021steering, electrical system, service brakes
I experienced loss of control by skidding and almost leaving the road toward a dropoff while applying the brake since the ABS, active handling, traction control systems have been malfunctioning at 35mph on a mountain road applying the brake as I was going around a sharp curve I believe the cause of this malfunction of the ABS/ah system is a faulty ebcm which is known by… Read more

I experienced loss of control by skidding and almost leaving the road toward a dropoff while applying the brake since the ABS, active handling, traction control systems have been malfunctioning at 35mph on a mountain road applying the brake as I was going around a sharp curve I believe the cause of this malfunction of the ABS/ah system is a faulty ebcm which is known by countless members of the Corvette owners community as a safety issue that should have been recalled a long time ago. If I would have known about this issue without an active recall I would not have bought the car. Several times this has happened in varied situations and I cannot rely on these safety features to save my life if something occurs that would send me out of control into another vehicle or over a steep cliff like in the close call I mentioned earlier in this text. GM does not value my life as much as I do and this recall would have bankrupted them shortly after 2000. I'm sure there are hundreds of thousands of wrecked corvettes and loss of life due to this failure to recall them so they should be able to afford it 20 years later

NHTSA complaint #11390943
Oct 4, 2018steering, electrical system
Tl* the contact owns a 2000 Chevrolet Corvette. The contact stated that the vehicle was repaired per NHTSA campaign number: 04v060000 (steering); however, the oem replacement part failed. The vehicle was towed back to the dealer (rick hendrick city Chevrolet, 5101 e independence blvd, charlotte, nc 28212, (980) 242-5621) within months due to the ignition locking and the… Read more

Tl* the contact owns a 2000 Chevrolet Corvette. The contact stated that the vehicle was repaired per NHTSA campaign number: 04v060000 (steering); however, the oem replacement part failed. The vehicle was towed back to the dealer (rick hendrick city Chevrolet, 5101 e independence blvd, charlotte, nc 28212, (980) 242-5621) within months due to the ignition locking and the security alarm randomly activating, which caused the vehicle to completely shut down. The vehicle was towed to a second dealer (fred caldwell Chevrolet, 974 bethel st, clover, sc 29710, 1-888-692-6546 and 1-803-222-4581). The manufacturer was contacted several times over the years and was aware that various fifth edition vehicles were affected. The manufacturer had not developed a newly designed oem part and expected the contact to have the part replaced a third time. The vehicle was not repaired. The vehicle was not included in NHTSA action numbers: ea02031 (steering) and pe02054 (steering). The manufacturer was notified of the failures. The failure mileage was not available.

NHTSA complaint #11133301
Sep 29, 2014electrical system, exterior lighting, service brakes
The hazard switch is faulty. All of the wiring for the brake and turn signals goes through the hazard switch. Every Corvette forum details the faulty hazard switch. Because of the poor quality of the part, and the poor design of the electrical system, if the hazard switch malfunctions, there are no brake lights, and/or no turn signals or hazard lights. There is no… Read more

The hazard switch is faulty. All of the wiring for the brake and turn signals goes through the hazard switch. Every Corvette forum details the faulty hazard switch. Because of the poor quality of the part, and the poor design of the electrical system, if the hazard switch malfunctions, there are no brake lights, and/or no turn signals or hazard lights. There is no indication that the switch is malfunctioning until another motorist notifies you verbally or by crashing into you, or perhaps if law enforcement pulls you over for it. *tr

NHTSA complaint #10640041
Aug 5, 2014electrical system, service brakes, engine
Tl* the contact owns a 2000 Chevrolet Corvette. The contact stated that the ABS and traction control indicators illuminated on the instrument panel. The dealer stated that the bpmv needed to be replaced along with other unknown failures. The manufacturer stated that the part needed for the repair was discontinued. The vehicle was not repaired. The failure mileage was 25,000. … Read more

Tl* the contact owns a 2000 Chevrolet Corvette. The contact stated that the ABS and traction control indicators illuminated on the instrument panel. The dealer stated that the bpmv needed to be replaced along with other unknown failures. The manufacturer stated that the part needed for the repair was discontinued. The vehicle was not repaired. The failure mileage was 25,000. Updated 09/17/14*lj updated 02/3/2015 *js

NHTSA complaint #10618946
Mar 27, 2014electrical system
2000 Chevrolet Corvette. Consumer writes in regards to vehicle ignition problems. *smd the consumer stated after the vehicle was purchased new in 2000, he had numerous problems with the ignition switch, on a random basis, but were not constant. On occasion, it would not start when the key was turned, and he would have to keep trying, until it did start. Sometimes it would… Read more

2000 Chevrolet Corvette. Consumer writes in regards to vehicle ignition problems. *smd the consumer stated after the vehicle was purchased new in 2000, he had numerous problems with the ignition switch, on a random basis, but were not constant. On occasion, it would not start when the key was turned, and he would have to keep trying, until it did start. Sometimes it would shut off on its own. The vehicle was taken to 3 different dealers, who said the could not help him unless the vehicle exhibited the problem, while in the shop. It wasn't until 3 years ago, when the ignition switch, became a regular problem, with starting and stopping and causing the steering wheel to lock up. There were times, when the engine would not shut off, after the key was removed. He disconnected the battery, hoping that resolve it, but it did not. There were times when the vehicle would shut off, while driving. *jb

NHTSA complaint #10574570
Mar 2, 2014electrical system
After the car was started and I began to drive ,it would shut off the motor and lock the steering wheel. All the lights would work fine,but the steering wheel locked until I came to a stop and would turn off the motor and restart the engine. It was very scary because I could not pull over to the side of the road and restart the motor. I would have to stop in the middle of the… Read more

After the car was started and I began to drive ,it would shut off the motor and lock the steering wheel. All the lights would work fine,but the steering wheel locked until I came to a stop and would turn off the motor and restart the engine. It was very scary because I could not pull over to the side of the road and restart the motor. I would have to stop in the middle of the road and start it. When I took the car into the dealer they said it was the key and key fob that was pulling the key out of the ignition and had to replace the entire key switch. This cost me $341.28 . I asked about any recalls or other people having the same problem and the reported to me that it is a common occurrence in the Corvette. Sounds like what was and is going on now and I think I should be paid back the money I spent by GM. *tr

NHTSA complaint #10566672
Sep 18, 2012steering, electrical system

Unable to unlock steering column after starting engine despite repeated attempts. Intermittently recurring problem. "service steering column lock" fault message appears in vehicle instrument panel display. *tr

NHTSA complaint #10475830
Apr 18, 2011electrical system, exterior lighting
Tl* the contact owns a 2000 Chevrolet Corvette. The contact stated unless the turn signals are being used, it is impossible for an operator to know when they are operable. The intermittent failure of the turn signals and hazards has been occurring for a few years. The frequency of the failures has increased and the failure duration has lengthened . Initially, the failure… Read more

Tl* the contact owns a 2000 Chevrolet Corvette. The contact stated unless the turn signals are being used, it is impossible for an operator to know when they are operable. The intermittent failure of the turn signals and hazards has been occurring for a few years. The frequency of the failures has increased and the failure duration has lengthened . Initially, the failure lasted for only a few seconds. The solution the contact discovered was to punch the hazard lights button a couple of times and this would somehow cause the turn signals to start operating. The problem was due to age and wear as well as bad parts. The headlights, window motors and driver's seat motor have all been replaced. The failure mileage was approximately 82,500. Updated 5/24/11 *cn updated 06/13/11

NHTSA complaint #10396692
Jun 13, 2009electrical system, latches/locks/linkages

Column lock on 200 Corvette failed, immobilizing vehicle. This device was subject to several prior recalls, but the replacement's design is still defective. Chevrolet dealer said that the recall has expired, so I had to pay for tow, parts/labor, and time off work. This amounts to nearly $1000. Since this is a safety-related design flaw, the recall should be reinstituted and I should be compensated. *tr

NHTSA complaint #10273707
Feb 19, 2008steering, latches/locks/linkages, electrical system
Tl*the contact owns a 2000 Chevrolet Corvette. The contact stated that the doors would not lock from the door panel, only from the key remote. Secondly, the ten second key delay began to activate and the horn blew out. While the mechanic was repairing the horn, the vehicle went into column lock. The repairs have been made, but the contact is concerned that the steering… Read more

Tl*the contact owns a 2000 Chevrolet Corvette. The contact stated that the doors would not lock from the door panel, only from the key remote. Secondly, the ten second key delay began to activate and the horn blew out. While the mechanic was repairing the horn, the vehicle went into column lock. The repairs have been made, but the contact is concerned that the steering column may lock while driving. A relay harness was removed from the vehicle and he does not believe it should have been removed. The purchase date was unknown. The current mileage was 54,410 and failure mileage was 54,011.

NHTSA complaint #10218558
Aug 31, 2007electrical system

In august 07 my 2000 Corvette coupe ebcm failed. The car has only 40,000 miles on it & is only driven on weekends. I am a mechanic by trade. I removed the module & had it rebuilt for $200 since GM quoted me $1300 for a new one. The repairs I made fixed the problem. *jb *updated 12/12/07 *bf the consumer stated the traction control, active handling and ABS light illuminated. Updated 12/12/07

NHTSA complaint #10201607
Aug 28, 2007electrical system
In early april I had a recall work completed on my 2000 Corvette done by buss cheverolet of shawano, a couple of months later the recall work failed, so parson's chevy of antigo, we redid the recall work. Now on 08-27-07 the recall work failed again! This will be the third time in less than 6 months I will have to have recall work done on my car for the column lock failure. … Read more

In early april I had a recall work completed on my 2000 Corvette done by buss cheverolet of shawano, a couple of months later the recall work failed, so parson's chevy of antigo, we redid the recall work. Now on 08-27-07 the recall work failed again! This will be the third time in less than 6 months I will have to have recall work done on my car for the column lock failure. This problem is well known to owners of c5 body style corvettes and most of these owners go and purchase their own bypass so it gets fixed correctly. Everyone I have spoken to indicates that when the dealership completes the work according to general motors direction the recall work always fail! When will general motors get it right? I shouldn't have to take my car into the dealership 3 times to have recall work done, especially when its a NHTSA ordered recall! *tr

NHTSA complaint #10200958
Jul 4, 2006electrical system, exterior lighting

Turn signals and hazard lights do not work all the time. When hot they do not work at all. *nm

NHTSA complaint #10161406
Nov 2, 2005steering, electrical system
Dt: the contact owns a 2000 Chevrolet Corvette. He stated that he parked, went into the grocery store, and when he came back out turned the vehicle on and the steering column would not unlock. He was told that there was recall 04v060000 on this type of vehicle. But the recall did not include his vehicle. The dealership told him that after doing the diagnostic test it was… Read more

Dt: the contact owns a 2000 Chevrolet Corvette. He stated that he parked, went into the grocery store, and when he came back out turned the vehicle on and the steering column would not unlock. He was told that there was recall 04v060000 on this type of vehicle. But the recall did not include his vehicle. The dealership told him that after doing the diagnostic test it was evident that it had nothing to do with driver's error. It may have been an electrical failure. The recall stated that it could lock up while driving. The dealership told him now that this vehicle was no longer under warranty. The contact will have to pay for the repairs to be done.*ak

NHTSA complaint #10141567
Jan 20, 2005electrical system
1. Fuel gauge drops to empty when I have around 1/2 a tank, low fuel light comes on. Have to put gas in to make light go out. I have to use odometer to keep track of how fuel I have used and how far can I go, because this will happen at any time. This happens all the time, every time. 2. Turn signals quit working at any time they please. I have to put the 4-ways on for… Read more

1. Fuel gauge drops to empty when I have around 1/2 a tank, low fuel light comes on. Have to put gas in to make light go out. I have to use odometer to keep track of how fuel I have used and how far can I go, because this will happen at any time. This happens all the time, every time. 2. Turn signals quit working at any time they please. I have to put the 4-ways on for about 5 seconds and then off to make the signals work again. *jb

NHTSA complaint #10107611
Jan 10, 2005electrical system
Eratic fuel readings, right rear tire sensor keeps going out this was replaced once already. Engine has knocking noise injectors were cleaned did not help. Wind noise from left window. Front right headlamp motor stopped working had to replace. Hud goes out on hot days. Car has on 2 occassions has stopped accelerating car has to be cut off and restarted to solve problem. This… Read more

Eratic fuel readings, right rear tire sensor keeps going out this was replaced once already. Engine has knocking noise injectors were cleaned did not help. Wind noise from left window. Front right headlamp motor stopped working had to replace. Hud goes out on hot days. Car has on 2 occassions has stopped accelerating car has to be cut off and restarted to solve problem. This vehicle has had many problems mainly electrical. *ak

NHTSA complaint #10106038
Aug 31, 2004electrical system

Electronic module for the automatic door locks failed. Consumer was concerned that he or other occupants would be trapped if doors failed again. *ak the vehicle's battery failed. When the battery was recharged it caused the power locks on the on the left side of the vehicle to fail. *nm

NHTSA complaint #10084019
Jun 4, 2004electrical system

While backing out steering locked. Vehicle screen indicator read pull key and wait ten seconds. Dealer stated electrical switch needed to be replaced. *ak

NHTSA complaint #10075726
Aug 15, 2003steering, electrical system

While driving 5 MPH the steering wheel without any warning locked up. Dealer notified. *ak the radio quit, directional switch, power doors/switch, and the door unlatched while the vehicle was in motion and while parked. *scc *jb

NHTSA complaint #10029762
Mar 31, 2003steering, engine and engine cooling, electrical system, exterior lighting, structure1 injured
The convertible top squealed,the driver side door exterior door handle had come loose, the right front turn signal had gone out, the vehicle excessively used oil, the vehicle had a recall on the steering ignition lock, ultimately the steering locked and the engine shut down while being backed out of the driveway, the gas guage malfunctioned, the traction control light had… Read more

The convertible top squealed,the driver side door exterior door handle had come loose, the right front turn signal had gone out, the vehicle excessively used oil, the vehicle had a recall on the steering ignition lock, ultimately the steering locked and the engine shut down while being backed out of the driveway, the gas guage malfunctioned, the traction control light had come on, the vehicle stalled, and the battery leaked acid. The consumer requested to be compensated for the inconvenience. Scc ref. In ea02-031 *cjs

NHTSA complaint #10011597
← All 2000 Chevrolet Corvette problems & recalls