While parked the parking brake lever release button jammed and I could not release the parking brakes. There is abnormal noise heard in the rear breaking system when reversing. Abnormal premature wear to inside rear brake pads and rotor discs
2008 Chevrolet Cobalt SS brakes problems
77 owners reported brakes problems — 81% of all 95 complaints about the 2008 Chevrolet Cobalt SS.
Brakes complaints by Chevrolet Cobalt SS year
What owners report
Rear brakes wear the pads unevenly and scratch the rotors. Common problem that most 2008+ Cobalt SS owners experience. Due to the faulty brakes, the hand brake will often not work, which is a large inconvenience in a car that is only available with a manual transmission. This is most noticeable when trying to park on a hill.
Engine light came on.... Had it checked by firestone... They told me the 2nd cylinder was misfiring per the diagnostic code.. Should be 130 psi and only registering 90 psi....then while stopped longer than 30 seconds "service traction" light comes on.....asking $2300 to repair.... Why would one of the four cylinders go bad.....complained to GM and they told me I needed a… Read more
Engine light came on.... Had it checked by firestone... They told me the 2nd cylinder was misfiring per the diagnostic code.. Should be 130 psi and only registering 90 psi....then while stopped longer than 30 seconds "service traction" light comes on.....asking $2300 to repair.... Why would one of the four cylinders go bad.....complained to GM and they told me I needed a certified GM dealer to look at it so I took it to GM also for diagnostic and they are saying misfire in 2nd cylinder which is what the diagnostic code says- per the paperwork given me they are not sure what the repair is going to entail or how to fix the problem..... Per internet complaints this s a problem that has occurred many times in cobalts.... Is it because no one got hurt or died that they don't want to consider this a recall? The car is only 9 years old and has 68800 miles on it.....and believe it or not the warranty expired 1000 miles ago... Very frustrating and unbelievable! Please help me understand. *tr
After climbing a steep driveway, brakes went to the floor when pulling out onto main road. Brakes would stop but continued to go to floor if 1) brakes were put on part of the way; release and then put on to stop again or 2) foot stayed on brake pedal upon stopping. It was not a sudden drop but a continuous movement of the pedal to the floor. Took to southtowne Chevrolet in… Read more
After climbing a steep driveway, brakes went to the floor when pulling out onto main road. Brakes would stop but continued to go to floor if 1) brakes were put on part of the way; release and then put on to stop again or 2) foot stayed on brake pedal upon stopping. It was not a sudden drop but a continuous movement of the pedal to the floor. Took to southtowne Chevrolet in newnan, ga and after a couple of attempts to repair the brakes (replacing front brakes, etc) a forman rode with me and they ended up having to flush the hydraulic system to get the brakes to stop. Upon hearing of the recall on the malibus this morning, I felt like my cobalt might have also suffered a potential hazard in its hydraulic system. *tr
On 10/2013, I was driving on the 105 fwy going eastbound at approximately 60 miles per hour when all of a sudden the vehicle stalled and I no longer could accelerate. East bound traffic was heavy and chp officer had to park behind me with his lights to avoid me getting hit by other vehicles, since there was no safety lane to pull over for broken down cars. The vehicle was… Read more
On 10/2013, I was driving on the 105 fwy going eastbound at approximately 60 miles per hour when all of a sudden the vehicle stalled and I no longer could accelerate. East bound traffic was heavy and chp officer had to park behind me with his lights to avoid me getting hit by other vehicles, since there was no safety lane to pull over for broken down cars. The vehicle was towed to one other place before being towed to penske Chevrolet, 18605 s studebaker rd., cerritos, ca 90703 the following day. In short, I took my car back 3 different times from the first time it was towed there. They would fix one part and I would leave and shortly after the engine light would come back on and I would return. Then they stated it was something else and they would "fix it". The check engine light would come back on once again. The last and final time I took my car in they replaced yet another car part and in total I paid $500.00 dollars in fees, not to mention time loss at work and gas they use to do "long test drives". To this day the check engine light is still on from the day I left penske Chevrolet. The manager there "[xxx]" in short stated that the car is fixed and that I would just have to deal with the check engine light being on. He assured me the second to last visit that this would be fixed and it never was. The vehicle is still not working as it did prior 10/2013. It cuts and does not accelerates when you initially step on the gas. In addition, the door locks are elec
The rear brake pads are worn severely unevenly. The inside pads are down to metal while the outside pads are still at least 50%. The rotors are deeply scored because of the wear. *tr
Excessive wear on rear brakes, causing untimely replacement. Rear brakes wear more quickly than fronts causing unsafe driving conditions. *tr
I have had to replace the rear brakes 4 times and still haven't replaced the front I get stock pads and rotors from chevy dealer! And within 500 miles the rotors are all scored up and look like they have 20k on them. I see this being a serious safety hazard for someone who does not realize it because they just replaced them! Fix this issue please! I noticed this for the 4th… Read more
I have had to replace the rear brakes 4 times and still haven't replaced the front I get stock pads and rotors from chevy dealer! And within 500 miles the rotors are all scored up and look like they have 20k on them. I see this being a serious safety hazard for someone who does not realize it because they just replaced them! Fix this issue please! I noticed this for the 4th time on december 1st. I was backing up and it made a horrible sound I got out to check and the rear pads are almost gone! I have put maybe 8k on them and the rotors look like a tiger attacked them, I don't believe I should have to pay for this again so soon! *tr
Rear brake rotors are irreparably scored and warped after 11,000 miles, preventing the rear brakes from working correctly and decreasing braking effectiveness. This is common on 2008 cobalt sses. *tr
Tl* the contact owns a 2008 Chevrolet Cobalt SS. The contact was driving 10 MPH when the vehicle failed to decrease in speed as the brakes were depressed. The vehicle was taken to a private mechanic. The manufacturer was not contacted. The vehicle was repaired. The VIN was unavailable. The failure mileage was 35,000 and the current mileage was 35,300.
Bought my Cobalt SS new from dealer, with less then 5,000 miles rear brakes were squealing and very obnoxious. Upon inspecting and bringing the car to the dealership was told that my brakes had gouges in them and needed to be refinished and cleaned as well as new pads installed. This was not covered under the warranty as they said it was wear and tear and the noise was normal. *tr
Rear brake rotors have massive gouges causing a grinding noise. *tr
1. Begin squeaking and e brake begins to no longer hold the car 2. Rear breaks pads wear out very quickly about every 10,000 to 15,000 miles 3. Put new pads on. *tr
At 8,000 miles the rear brake rotors were deeply groved. The front rotors looked fine, no groves. At 18,000 we had to swap out the pads as the friction surface was completely gone. We discussed the problem with the dealer on both occasions, but they said there was nothing they could do as there was no recall. I also tried to question if the problem was with the rotors or… Read more
At 8,000 miles the rear brake rotors were deeply groved. The front rotors looked fine, no groves. At 18,000 we had to swap out the pads as the friction surface was completely gone. We discussed the problem with the dealer on both occasions, but they said there was nothing they could do as there was no recall. I also tried to question if the problem was with the rotors or pads or calipers, but they said they could not answer these questions. I'm just looking for some answers and service support. *tr
The rear brakes on the 2008-2010 models of the Chevrolet Cobalt SS wear out immaturely causing pulsation, lack of braking poor, and costly fixes. *tr
I have noticed excessive wear on my rear brakes and groves forming on my rotors too. I have a 2008 chevy Cobalt SS turbo. The dealer is saying it is normal wear and tear but I believe it is something more than wear and tear. My complaints to the dealer has gone unheard and will not be addressed. *tr
My rear rotors have scarred so bad it is affecting braking, and they have already been replaced once. They are noisy, dangerous, and visually unpleasing. *tr
Rear brakes wearing out, parking brake does not hold, squeals when stopping. *tr
Rear brakes on 2008 Chevrolet Cobalt SS worn significantly. Parking brake has very little tension. Grinding noise also comes from rear brakes. *tr
Under normal daily driving conditions (majority is commuting), my rear rotors and brakr pads were replaced at 21,259km, quote from service order from my dealership, "rear brakes at squealers, confirmed squeal noise from rear. Found rear brake pads at squealers. Both rotors badlyscored. Machined rotors lr19.0mm and rr19.10mm replaced rear brake pads". Then at 42,465km… Read more
Under normal daily driving conditions (majority is commuting), my rear rotors and brakr pads were replaced at 21,259km, quote from service order from my dealership, "rear brakes at squealers, confirmed squeal noise from rear. Found rear brake pads at squealers. Both rotors badlyscored. Machined rotors lr19.0mm and rr19.10mm replaced rear brake pads". Then at 42,465km brought vehicle to dealership as I could smell burning brakes from the rear end after only 20 min of daily average driving . Following is a quote from my dealership work order, "cause: seized/binds/sticks. Found rear brakes @ 2mm remaining on rear inboard pad. Checked complete hydraulic sys. Checked for ABS codes. Checked for bulletins on rear brakes. Checked e brake no problems found. Removed rear calipers and found calipers sticky. Need to be replaced both rear calipers sticky. Need to replace both rear calipers, rotors and pads. Inner pads 2mm outboard 6mm and rotors undr min. Replaced both rear calipers, rotors and brake pads. Bled brake system". Then my dealership followed with "this will be the last time GM will replace rear brakes". As far as I am concerned if the rear brakes are inadequate fro the application and are being worn out and damaging brake parts every 20,000km or so then a recall needs to be done with replacements of an adequate breaking components. *tr
The rear brakes on the Chevrolet Cobalt SS are pure crap. They squeal pretty badly when you come to a stop, no matter if it's a fast stop or a slow stop. It gets even louder when they get hot. I've taken to my car to the dealer since my 08 cobalt is still under warranty and they've told me that high performance brakes are supposed to be loud...I'm sorry GM, but not this loud!… Read more
The rear brakes on the Chevrolet Cobalt SS are pure crap. They squeal pretty badly when you come to a stop, no matter if it's a fast stop or a slow stop. It gets even louder when they get hot. I've taken to my car to the dealer since my 08 cobalt is still under warranty and they've told me that high performance brakes are supposed to be loud...I'm sorry GM, but not this loud! So they rotated my rotors, and gave me new brakes about a month ago, and it's still as bad as when I got the car back in april of this year. *tr
1) I drove my car and used the brakes. 2) scored brakes, sounds like a 747 coming in for a landing every time I stop. 3) nothing yet, called the dealership today (05/24/10). *tr
Rear brake rotors and discs wear out far too quickly in average day to day use. *tr
The rear brake calipers fail to release properly, causing the inside brake pad to wear more than twice as fast as the outside pad. Therefore forcing the rear pads to be replaced twice as often as the front brake pads. *tr
My 2008 Chevrolet Cobalt SS rear brakes had to be changed before the front brakes (40000km). The rotors were heavily scored to a point where they could not be resurfaced. The pads were worn out unevenly and had a different levels of wear. The front brakes at 60000 still have lots of brake pad left. I replaced the brakes myself and did not keep the old parts. *tr
Rear brake pads worn out after 20k mile and rotor are groved and you can hear the brake pads rubbing metal on metal. Also the rear calipers aren't releasing the rear rotors correctly due to caliper slide pins not being lubricated from the factory. Front brake pads and rotor are wearing normally. I dropped my car off at my local Chevrolet dealership for the brakes to be fixed… Read more
Rear brake pads worn out after 20k mile and rotor are groved and you can hear the brake pads rubbing metal on metal. Also the rear calipers aren't releasing the rear rotors correctly due to caliper slide pins not being lubricated from the factory. Front brake pads and rotor are wearing normally. I dropped my car off at my local Chevrolet dealership for the brakes to be fixed under warranty. I was told if it was a caliper issue then it would be covered underwarranty. *tr
The rear brakes on my 2008 Cobalt SS/tc were completely shot at around 14000 miles. The gouges in the rotors were too deep to get turned and I had to do a full brake job on the rear brakes because GM said that they only cover the brakes until 12,000 miles. The new brakes still make strange noises and when the car is in reverse sometimes a very loud screech comes from them. *tr
The problem I am experiencing with my 2008 Chevrolet Cobalt SS is the rear brake pads wearing out quickly under normal driving conditions. Because the brake bias is set to the front brakes, they should wear out long before the rear brakes. I believe the problem lies in the hardware of the braking package. Either the caliper is causing the pad to constantly rub the rotor or… Read more
The problem I am experiencing with my 2008 Chevrolet Cobalt SS is the rear brake pads wearing out quickly under normal driving conditions. Because the brake bias is set to the front brakes, they should wear out long before the rear brakes. I believe the problem lies in the hardware of the braking package. Either the caliper is causing the pad to constantly rub the rotor or some other issue is present. I first noticed that the rotors were scored at about 3,000 miles, was told it was normal. At 20,000 miles the rear pads were down to the metal on the inside pad. Also, its not just a problem with the rear pads, every rotor on the car is scored beyond normal wear. This is a known problem with a lot of the 2008+ ss cobalts, not with the way they are being driven. General motors is aware of the problem, as many people have complained. When I took my car to the dealer, they too said that it was uneven wear that should not have happened. But, instead of looking into the cause of the problem, they simply replaced the rear pads. This was a temporary "patch" not a fix. In 5,000 miles, they'll start to wear again unevenly. I think general motors needs to evaluate the rotors and pads on these cars. Under no circumstances, is there an excuse for the brakes and rotors to be worn out on these cars at 20,000 miles under daily driving conditions. If the problem only effected a couple of cars, it could be blamed on the driving patterns of the operator. However, this is a common problem for all
Rear brake calipers not applying even force on both inner and outer pads, causing premature wear and tear on the pads and rotors, and additional stress on the braking system. *tr
Everything was fine until about 6000 miles when I noticed slight brake noise coming from the rear brakes. I didnt notice the groves in the rotors until after I got stuck on interstate 465 in the snow because the back brakes were dragging. I know the back brakes were dragging because I had to put my car into first gear and push my own car with the door open. I know bad idea. I… Read more
Everything was fine until about 6000 miles when I noticed slight brake noise coming from the rear brakes. I didnt notice the groves in the rotors until after I got stuck on interstate 465 in the snow because the back brakes were dragging. I know the back brakes were dragging because I had to put my car into first gear and push my own car with the door open. I know bad idea. I noticed that the rear tires didn't start rolling until they got to clean pavement. There was less than one inch of snow on the roads. It took me two hours to get home from work which is a fifteen minute drive normally. I had to wait a week for the snow to melt so I could drive my car to the dealership and they gave me a loner vehicle which I drove for over three weeks waiting for them to fix my car. They couldn't tell me what was wrong but they did replace the pads and rotors. This occured at roughly 10,000 miles. And 10,000 miles later the rotors were grooved again. So I went back to the dealership again this time they didn't want to fix the brakes but my uncle knows the owner of the dealership and he got them to fix it. I drove a loner again for a few weeks. And finally I took my car back to the dealership last week with 32,895 miles on it with the exact same problem. This time they said g.m. Won't cover the repair under warranty. They said the brakes failed due to being dirty. Lol ! I wash my car every week. I still have the defective parts on my car that I drive everyday. The brake noise is slowly ge
1. Normal driving conditions since purchase of vehicle in july 2008. 2. Failure includes extreme premature wear and scoring on rear rotors and uneven wear on rear brake pads. 3. Original dealership turned and milled rear rotors at 7800 miles. Vehicle is now back at same dealer at 16000 miles for same issue.
Rear brakes wearing way too early. *tr
Brakes wore out prematurely and grind. *tr
Rear breaks grinding and worn out after 15k miles. *cn
Back brakes on my Cobalt SS are shot and the rotors and scorched and worn out. *tr
I own a 2008 chevy Cobalt SS. The rear brake pads were wearing out very quickly and damaging the rotors. First noticed a grinding noise on the rear brakes at 950 miles and now at 16,500 miles, I am sitting at the dealer service dept. Being told that my pads and rotors need to be replaced. The previous dealer ignored my requests to have this corrected before it got this bad.… Read more
I own a 2008 chevy Cobalt SS. The rear brake pads were wearing out very quickly and damaging the rotors. First noticed a grinding noise on the rear brakes at 950 miles and now at 16,500 miles, I am sitting at the dealer service dept. Being told that my pads and rotors need to be replaced. The previous dealer ignored my requests to have this corrected before it got this bad. This dealer looked at it and they said that the car is not safe to drive until the brakes are replaced. So I am waiting to see if they will repair it or give me a loaner until it can be repaired. *tr updated 02/02/10 *bf updated 02/05/10*jb
The rear rotors are grooved because of the faulty design and the pads are scoring the rotors. *tr
The rear brakes on my 2008 chevy Cobalt SS turbocharged make excessive noise in reverse, this problem is common from what I understand, and is no fault of the owner. *tr
Just bought car used with 26k miles and rear brakes are metal to metal. So far dealer cant find parts in there system for my car. *tr
Normal driving has caused my rear brakes to be totally shot at 15000 miles. Have not tried to warranty the item yet, but I have heard they will not replace the item. *tr