CarProblemsDB

2006 BMW 750LI brakes problems

22 owners reported brakes problems — 10% of all 216 complaints about the 2006 BMW 750LI.

Brakes complaints by BMW 750LI year

20121
20086
20079
200622

What owners report

Aug 3, 2022service brakes, hydraulic, engine
The contact owns a 2006 BMW 750LI. The contact stated that while driving at an undisclosed speed, several unknown warning lights illuminated. Additionally, there was oil leaking onto the ground and also onto the engine. The vehicle was taken to an independent mechanic who diagnosed that the brake vacuum pump needed to be replaced. The vehicle was not repaired. The manufacturer… Read more

The contact owns a 2006 BMW 750LI. The contact stated that while driving at an undisclosed speed, several unknown warning lights illuminated. Additionally, there was oil leaking onto the ground and also onto the engine. The vehicle was taken to an independent mechanic who diagnosed that the brake vacuum pump needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA. The failure mileage was approximately 129,000.

NHTSA complaint #11477374
Jun 27, 2020power train, structure, latches/locks/linkages, electronic stability control (esc), service brakes

Car doors do not latch doors fly open , car has rolled out of park, brakes do not engage ruff stopping seat belt lights on all the time. Problems with electrical seats. *tr

NHTSA complaint #11331231
Jun 24, 2020service brakes, hydraulic
Tl* the contact owns a 2006 BMW 750LI. The contact stated that while driving, the brake pedal was depressed and was firm. The contact stated that extra effort was needed to stop the vehicle. The contact was informed by an unknown source that the brake booster and vacuum pump needed to be replaced. The vehicle was not diagnosed nor repaired. Neither the dealer nor the… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact stated that while driving, the brake pedal was depressed and was firm. The contact stated that extra effort was needed to stop the vehicle. The contact was informed by an unknown source that the brake booster and vacuum pump needed to be replaced. The vehicle was not diagnosed nor repaired. Neither the dealer nor the manufacturer were notified of the failure. The failure mileage was 154,000.

NHTSA complaint #11330592
Feb 21, 2020electronic stability control (esc), service brakesCrash

ABS is completely messed up car slides at every turn/move! If brakes are pressed a little to fast brakes block and doesn't stop the car! Which caused me to crash into another car!

NHTSA complaint #11310647
Jul 24, 2017latches/locks/linkages, service brakes
Tl* the contact owns a 2006 BMW 750LI. While driving at any speed, the brake pedal felt "soft" and did not fully stop the vehicle. There were no warning indicators illuminated. The vehicle was taken to an independent mechanic who diagnosed that the brake booster needed to be replaced. The dealer was not contacted. The manufacturer was made aware of the failure and stated that… Read more

Tl* the contact owns a 2006 BMW 750LI. While driving at any speed, the brake pedal felt "soft" and did not fully stop the vehicle. There were no warning indicators illuminated. The vehicle was taken to an independent mechanic who diagnosed that the brake booster needed to be replaced. The dealer was not contacted. The manufacturer was made aware of the failure and stated that there was no recall. The contact received notification of NHTSA campaign number: 17v328000 (latches/locks/linkages). The failure mileage was 123,000. VIN tool confirms parts not available.

NHTSA complaint #11010268
Mar 9, 2017service brakes
Tl* the contact owns a 2006 BMW 750LI. The contact stated that the vehicle was taken to a dealer for a manufacturer recall for the brake system. The dealer indicated that they provided the remedy, but the contact stated that the brake pedal was extremely difficult to depress. The contact had to place both feet on the brake pedal to ensure that the vehicle had come to a… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact stated that the vehicle was taken to a dealer for a manufacturer recall for the brake system. The dealer indicated that they provided the remedy, but the contact stated that the brake pedal was extremely difficult to depress. The contact had to place both feet on the brake pedal to ensure that the vehicle had come to a complete stop. There were no warning indicators each time the brake system failed. The vehicle was also taken to several independent mechanics for diagnostic testing. The recall repair remedy provided no solution. The manufacturer was notified. The recall information was not provided. The failure mileage was not available.

NHTSA complaint #10959761
Jan 9, 2017parking brake

Tl* the contact owns a 2006 BMW 750LI. The contact stated that the emergency brakes did not engage and, when parked on an incline, the vehicle rolled away. The vehicle was scheduled for a recall repair at the dealer. The manufacturer was notified of the failure. The vehicle was not repaired. The approximate failure mileage was 84,000.

NHTSA complaint #10943854
Oct 25, 2016service brakesCrash
Brake vacuum pump booster has failed due to contamination even after brake booster supply line was replaced in december, 4, 2010. When vehicle is in motion, the car loses power to brakes, brake pedal feels hard and vehicle takes 20-30 ft longer to brake even if pushing down with maximum force. This caused vehicle to take an infinite amount of time to stop, which resulted in… Read more

Brake vacuum pump booster has failed due to contamination even after brake booster supply line was replaced in december, 4, 2010. When vehicle is in motion, the car loses power to brakes, brake pedal feels hard and vehicle takes 20-30 ft longer to brake even if pushing down with maximum force. This caused vehicle to take an infinite amount of time to stop, which resulted in car nearly running into another vehicle when issue occurred. Luckily I swerved off highway unto median. This issue can result in death or catastrophic accident as brake booster vacuum pump is affected in such a way that brake power is 50% less than normal, low to negligible brake power means car does not stop normally, it takes more time to stop, which can lead to death from rear end collisions, freak accidents and even running into persons or objects when parking.

NHTSA complaint #10918797
Apr 8, 2016service brakes
Tl* the contact owns a 2006 BMW 750LI. The contact was notified of NHTSA campaign number: 10v446000 (service brakes, hydraulics) by an independent technician due to a brake failure. The vehicle was taken to the dealer where it was confirmed that the vehicle was under the recall. The vehicle was taken to the dealer where the brake clamp and vacuum pipe were replaced. Although… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact was notified of NHTSA campaign number: 10v446000 (service brakes, hydraulics) by an independent technician due to a brake failure. The vehicle was taken to the dealer where it was confirmed that the vehicle was under the recall. The vehicle was taken to the dealer where the brake clamp and vacuum pipe were replaced. Although the vehicle was repaired, the brakes still failed. The vehicle was returned to the dealer where it was diagnosied that the vehicle's brake booster needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 81,000.

NHTSA complaint #10854285
Apr 8, 2014service brakes, hydraulic, engine and engine cooling
2006 BMW 750 li. Consumer writes in regards to vehicle oil leak and major mechanical problems. *smd the dealer agreed to fix the vehicle. However, when the consumer picked the vehicle up, the leak was still present. The consumer went to another dealer, where she was informed the vehicle had multiple leaks; the alternator mount bracket seal was leaking, as well as the valve… Read more

2006 BMW 750 li. Consumer writes in regards to vehicle oil leak and major mechanical problems. *smd the dealer agreed to fix the vehicle. However, when the consumer picked the vehicle up, the leak was still present. The consumer went to another dealer, where she was informed the vehicle had multiple leaks; the alternator mount bracket seal was leaking, as well as the valve guide seals, the upper timing case cover seals, the valley pan was leaking coolant and the vacuum pump was leaking. The mechanic stated even though the vehicle had a good appearance, he observed signs of wear on the engine parts and road grime and stains on other engine parts. *jb updated 04/16/14. *jb

NHTSA complaint #10577655
Feb 6, 2014service brakes
Tl* the contact owns a 2006 BMW 750LI. The contact stated while driving approximately 65 MPH there was a power assist braking performance failure and the brakes required full force in order to come to a complete stop. The contact experience an increased stopping distance. The vehicle was taken to a dealer where it was diagnosed that the brake booster needed to be replaced. The… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact stated while driving approximately 65 MPH there was a power assist braking performance failure and the brakes required full force in order to come to a complete stop. The contact experience an increased stopping distance. The vehicle was taken to a dealer where it was diagnosed that the brake booster needed to be replaced. The manufacturer was notified of the failure and stated that the vehicle was previously repaired under NHTSA campaign number: 10v446000 (service brakes hydraulic). The vehicle was not repaired. The approximate failure and current mileage was 72,000.

NHTSA complaint #10563266
Dec 6, 2013electrical system, service brakes
Brake peddle appear to resist depression, and braking becomes difficult or impossible. The resistance feels like a control system resisting, and preventing the peddle from being depressed. But it could possibly be a failure of power assist, but it feels like a hard, but slightly spongy resistance, like a hydraulic system closed a valve down stream of the brakes. The issue… Read more

Brake peddle appear to resist depression, and braking becomes difficult or impossible. The resistance feels like a control system resisting, and preventing the peddle from being depressed. But it could possibly be a failure of power assist, but it feels like a hard, but slightly spongy resistance, like a hydraulic system closed a valve down stream of the brakes. The issue began abruptly 5 days ago, from no indication at all of an issue, to an abrupt issue in full effect. Now it is consistant, and very repeatable. When braking to a stop from over 20 MPH, the brakes work normally down to ~10mph. Then between 10 and 7 MPH, the brakes feel like they are pushing back, if not strongly resisting depression. Braking is difficult and dangerous. Take caution. *tr

NHTSA complaint #10555137
Feb 19, 2013service brakes, hydraulic, power train, engine
2 separate issues 1st, the vehicle when in park cannot switch to drive or reverse, it will only switch to neutral. Happen on countless occasions. Brought the vehicle to russell BMW who told me I have to pay to replace the transmission. Recall 93562 is now posted on BMW website detailing the same issue. Spoke to a rep who dismissed my vehicle complaint because the VIN # does… Read more

2 separate issues 1st, the vehicle when in park cannot switch to drive or reverse, it will only switch to neutral. Happen on countless occasions. Brought the vehicle to russell BMW who told me I have to pay to replace the transmission. Recall 93562 is now posted on BMW website detailing the same issue. Spoke to a rep who dismissed my vehicle complaint because the VIN # does not fall under the luxury package therefore not included in the recall. 2nd issue..the vehicle brakes when applied does not stop. Twice it's happen when I tried to slow or stop resulting in scaring me half to death and near accidents. I also address the recall 87903 with the rep who once again told me the VIN is not covered in the recall even though the year and model is included as part of the recall the question I pose is why is the VIN determining the qualification of the need to have BMW responsibly fix the 1st year model of their trial and error vehicles. I paid way too much to be told that because I did not have the comfort package my vehicle is not included in their recall? Is it going to take an accident for BMW to be fix the necessary problems? *tr

NHTSA complaint #10499252
Dec 6, 2012service brakes, hydraulic, engine

Took my car in to be serviced and was informed of this leak in the vacuum pump and steering switch. Consequently, I seen there was a recall for 2006 bmws with a NHTSA campaign id number of 10v446000 with a recall date of 2012-10-01 for the vacuum pump. I called the dealership and they told me my car wasn't included.....but I believe it should be. *tr

NHTSA complaint #10487518
Oct 9, 2012service brakes, hydraulic
Tl* the contact owns a 2006 BMW 750LI. The contact stated that while driving 40 MPH, the contact depressed the brake pedal but the brake booster did not activate. The vehicle was taken to the dealer for inspection and they stated that the vacuum pump and the brake booster failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified who… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact stated that while driving 40 MPH, the contact depressed the brake pedal but the brake booster did not activate. The vehicle was taken to the dealer for inspection and they stated that the vacuum pump and the brake booster failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified who confirmed that the vehicle was not included in recall NHTSA campaign id number: 10v446000 (service brakes, hydraulic: power assist: vacuum). The failure mileage was 100,000. ..updated 11/26/12 *bf the consumer stated vacuum pump leaked oil into the vacuum booster pipe that connected to the brake booster. Oil deteriorated the booster, which resulted in power brake failure. Updated 11/28/12

NHTSA complaint #10479336
Jun 27, 2012engine and engine cooling, service brakes
. While driving I came to a intersection I depressed the brake pedal but the brakes did not respond. I continually applied pressure to the brake pedal until the brakes responded. The vehicle was taken to an independent mechanic for diagnostic testing where the mechanic replaced the front brakes and rotors. The mechanic found contamination in the brake booster and … Read more

. While driving I came to a intersection I depressed the brake pedal but the brakes did not respond. I continually applied pressure to the brake pedal until the brakes responded. The vehicle was taken to an independent mechanic for diagnostic testing where the mechanic replaced the front brakes and rotors. The mechanic found contamination in the brake booster and notification of NHTSA campaign id number: 10v446000 (service brakes, hydraulic:power assist:vacuum) the vehicle was towed to the dealer. The dealer changed the valves & then told me I had to pay for diagnostic cause the breaks weren't working which I did paid $149 plus tax. After the diagnostic the technician stated that the brake booster would have to be replaced. Per the recall, the brake booster could become contaminated over time due to the recalled failure. The manufacture advised me that the repairs would not be covered. *tr

NHTSA complaint #10463342
Jun 6, 2012service brakes
Tl* the contact owns a 2006 BMW 750LI. The contact received notification of NHTSA campaign id number: 10v446000 (service brakes, hydraulic:power assist:vacuum) and was taken to the dealer for repairs. The contact stated that the brake warning light illuminated after the repairs while driving approximately 25 MPH. The contact depressed the brake pedal but the brakes did not… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact received notification of NHTSA campaign id number: 10v446000 (service brakes, hydraulic:power assist:vacuum) and was taken to the dealer for repairs. The contact stated that the brake warning light illuminated after the repairs while driving approximately 25 MPH. The contact depressed the brake pedal but the brakes did not respond. The contact continually applied pressure to the brake pedal until the brakes responded. The vehicle was taken to an independent mechanic for diagnostic testing where the mechanic replaced the rear brakes and rotors. The mechanic found contamination in the brake booster and the vehicle was towed to the dealer. The technician stated that the brake booster would have to be replaced. The contact stated that per the recall, the brake booster could become contaminated over time due to the recalled failure. The manufacturer advised the contact that the repairs would not be covered. The vehicle was not further repaired. The approximate failure mileage was 92,000.

NHTSA complaint #10460827
Oct 19, 2011parking brake, latches/locks/linkages
Tl* the contact owns a 2006 BMW 750LI. The contact stated that the parking brake would not latch, causing the vehicle to roll away when parked and shut off. In addition, the automatic door latch was inoperable and while driving 30 MPH, he had to hold the driver side door to keep it from opening. The vehicle was taken to the dealer who advised that there were no recalls for… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact stated that the parking brake would not latch, causing the vehicle to roll away when parked and shut off. In addition, the automatic door latch was inoperable and while driving 30 MPH, he had to hold the driver side door to keep it from opening. The vehicle was taken to the dealer who advised that there were no recalls for the vehicle and offered no assistance. The manufacturer was not notified of the failures. The failure mileage was 67,000.

NHTSA complaint #10430830
Sep 30, 2011service brakes, hydraulic
After receiving a recall letter from BMW for the brake vacuum pump (recall campaign no. 10v-446), I took the car to crevier BMW but was told they didn't have the part. Never heard back from crevier BMW, forgot about it until the brakes completely failed without warning. Had the car towed to the nearest dealer in irvine. They replaced the vacuum supply line but not the vacuum… Read more

After receiving a recall letter from BMW for the brake vacuum pump (recall campaign no. 10v-446), I took the car to crevier BMW but was told they didn't have the part. Never heard back from crevier BMW, forgot about it until the brakes completely failed without warning. Had the car towed to the nearest dealer in irvine. They replaced the vacuum supply line but not the vacuum pump. They recommended I replace the leaking vacuum pump at my cost of over $900.the description of the problem included in the recall letter from BMW specifically indicates that the leak from the vacuum pump into the vacuum hose, is the root of the problem. I spoke to j, mcclain at BMW and she said that the recall is a federal mandate and this mandate only requires them to replace the line not the pump. *tr

NHTSA complaint #10428080
Sep 29, 2011service brakes, hydraulic
Tl* the contact owns a 2006 BMW 750LI. The contact stated that while driving approximately 15 MPH, she applied the brakes, but the brakes did not respond. The contact was able to stop the vehicle and had it towed to the dealer. The technician stated that the master cylinder, vacuum supply line, and brake booster would have to be replaced under the recall associated with NHTSA… Read more

Tl* the contact owns a 2006 BMW 750LI. The contact stated that while driving approximately 15 MPH, she applied the brakes, but the brakes did not respond. The contact was able to stop the vehicle and had it towed to the dealer. The technician stated that the master cylinder, vacuum supply line, and brake booster would have to be replaced under the recall associated with NHTSA campaign id number 10v446000 (service brakes, hydraulic:power assist:vacuum). The technician also stated that the vacuum pump would have to be replaced, but it was not covered under the recall. The contact stated that the recall indicated that the vacuum pump was the source of the failure and it should have been replaced. The vehicle was not repaired. The approximate failure mileage was 119,000.

NHTSA complaint #10427954
← All 2006 BMW 750LI problems & recalls